README 217 KB
Newer Older
wdenk's avatar
wdenk committed
1
#
2
# (C) Copyright 2000 - 2013
wdenk's avatar
wdenk committed
3 4
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
5
# SPDX-License-Identifier:	GPL-2.0+
wdenk's avatar
wdenk committed
6 7 8 9 10
#

Summary:
========

11
This directory contains the source code for U-Boot, a boot loader for
12 13 14 15
Embedded boards based on PowerPC, ARM, MIPS and several other
processors, which can be installed in a boot ROM and used to
initialize and test the hardware or to download and run application
code.
wdenk's avatar
wdenk committed
16 17

The development of U-Boot is closely related to Linux: some parts of
18 19
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
wdenk's avatar
wdenk committed
20 21 22 23 24 25 26 27 28 29 30 31 32 33
support booting of Linux images.

Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.


Status:
=======

In general, all boards for which a configuration option exists in the
34
Makefile have been tested to some extent and can be considered
wdenk's avatar
wdenk committed
35 36
"working". In fact, many of them are used in production systems.

37 38 39 40
In case of problems see the CHANGELOG file to find out who contributed
the specific port. In addition, there are various MAINTAINERS files
scattered throughout the U-Boot source identifying the people or
companies responsible for various boards and subsystems.
wdenk's avatar
wdenk committed
41

42 43 44
Note: As of August, 2010, there is no longer a CHANGELOG file in the
actual U-Boot source tree; however, it can be created dynamically
from the Git log using:
45 46 47

	make CHANGELOG

wdenk's avatar
wdenk committed
48 49 50 51

Where to get help:
==================

52
In case you have questions about, problems with or contributions for
53
U-Boot, you should send a message to the U-Boot mailing list at
54 55 56 57
<u-boot@lists.denx.de>. There is also an archive of previous traffic
on the mailing list - please search the archive before asking FAQ's.
Please see http://lists.denx.de/pipermail/u-boot and
http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
wdenk's avatar
wdenk committed
58 59


60 61 62
Where to get source code:
=========================

63
The U-Boot source code is maintained in the Git repository at
64 65 66 67
git://www.denx.de/git/u-boot.git ; you can browse it online at
http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary

The "snapshot" links on this page allow you to download tarballs of
68
any version you might be interested in. Official releases are also
69 70 71
available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
directory.

72
Pre-built (and tested) images are available from
73 74 75
ftp://ftp.denx.de/pub/u-boot/images/


wdenk's avatar
wdenk committed
76 77 78 79
Where we come from:
===================

- start from 8xxrom sources
80
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenk's avatar
wdenk committed
81 82 83 84 85 86 87
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
  * Provide extended interface to Linux boot loader
  * S-Record download
  * network boot
88
  * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
89
- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenk's avatar
wdenk committed
90
- add other CPU families (starting with ARM)
91
- create U-Boot project (http://sourceforge.net/projects/u-boot)
92
- current project page: see http://www.denx.de/wiki/U-Boot
93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114


Names and Spelling:
===================

The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:

	This is the README file for the U-Boot project.

File names etc. shall be based on the string "u-boot". Examples:

	include/asm-ppc/u-boot.h

	#include <asm/u-boot.h>

Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:

	U_BOOT_VERSION		u_boot_logo
	IH_OS_U_BOOT		u_boot_hush_start
wdenk's avatar
wdenk committed
115 116


117 118 119
Versioning:
===========

120 121 122 123 124 125 126 127
Starting with the release in October 2008, the names of the releases
were changed from numerical release numbers without deeper meaning
into a time stamp based numbering. Regular releases are identified by
names consisting of the calendar year and month of the release date.
Additional fields (if present) indicate release candidates or bug fix
releases in "stable" maintenance trees.

Examples:
128
	U-Boot v2009.11	    - Release November 2009
129
	U-Boot v2009.11.1   - Release 1 in version November 2009 stable tree
130
	U-Boot v2010.09-rc1 - Release candidate 1 for September 2010 release
131 132


wdenk's avatar
wdenk committed
133 134 135
Directory Hierarchy:
====================

136
/arch			Architecture specific files
137
  /arc			Files generic to ARC architecture
138 139 140 141 142 143
  /arm			Files generic to ARM architecture
  /avr32		Files generic to AVR32 architecture
  /blackfin		Files generic to Analog Devices Blackfin architecture
  /m68k			Files generic to m68k architecture
  /microblaze		Files generic to microblaze architecture
  /mips			Files generic to MIPS architecture
144
  /nds32		Files generic to NDS32 architecture
145
  /nios2		Files generic to Altera NIOS2 architecture
146
  /openrisc		Files generic to OpenRISC architecture
147
  /powerpc		Files generic to PowerPC architecture
148
  /sandbox		Files generic to HW-independent "sandbox"
149 150
  /sh			Files generic to SH architecture
  /sparc		Files generic to SPARC architecture
151
  /x86			Files generic to x86 architecture
152 153
/api			Machine/arch independent API for external apps
/board			Board dependent files
154
/cmd			U-Boot commands functions
155
/common			Misc architecture independent functions
156
/configs		Board default configuration files
157 158 159
/disk			Code for disk drive partition handling
/doc			Documentation (don't expect too much)
/drivers		Commonly used device drivers
160
/dts			Contains Makefile for building internal U-Boot fdt.
161 162 163
/examples		Example code for standalone applications, etc.
/fs			Filesystem code (cramfs, ext2, jffs2, etc.)
/include		Header Files
164 165
/lib			Library routines generic to all architectures
/Licenses		Various license files
166 167
/net			Networking code
/post			Power On Self Test
168 169
/scripts		Various build scripts and Makefiles
/test			Various unit test files
170
/tools			Tools to build S-Record or U-Boot images, etc.
wdenk's avatar
wdenk committed
171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186

Software Configuration:
=======================

Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.

There are two classes of configuration variables:

* Configuration _OPTIONS_:
  These are selectable by the user and have names beginning with
  "CONFIG_".

* Configuration _SETTINGS_:
  These depend on the hardware etc. and should not be meddled with if
  you don't know what you're doing; they have names beginning with
187
  "CONFIG_SYS_".
wdenk's avatar
wdenk committed
188

189 190 191 192 193
Previously, all configuration was done by hand, which involved creating
symbolic links and editing configuration files manually. More recently,
U-Boot has added the Kbuild infrastructure used by the Linux kernel,
allowing you to use the "make menuconfig" command to configure your
build.
wdenk's avatar
wdenk committed
194 195 196 197 198 199


Selection of Processor Architecture and Board Type:
---------------------------------------------------

For all supported boards there are ready-to-use default
200
configurations available; just type "make <board_name>_defconfig".
wdenk's avatar
wdenk committed
201 202 203 204

Example: For a TQM823L module type:

	cd u-boot
205
	make TQM823L_defconfig
wdenk's avatar
wdenk committed
206

207 208 209
Note: If you're looking for the default configuration file for a board
you're sure used to be there but is now missing, check the file
doc/README.scrapyard for a list of no longer supported boards.
wdenk's avatar
wdenk committed
210

211 212 213 214 215 216 217 218
Sandbox Environment:
--------------------

U-Boot can be built natively to run on a Linux host using the 'sandbox'
board. This allows feature development which is not board- or architecture-
specific to be undertaken on a native platform. The sandbox is also used to
run some of U-Boot's tests.

219
See board/sandbox/README.sandbox for more details.
220 221


222 223 224 225
Board Initialisation Flow:
--------------------------

This is the intended start-up flow for boards. This should apply for both
226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241
SPL and U-Boot proper (i.e. they both follow the same rules).

Note: "SPL" stands for "Secondary Program Loader," which is explained in
more detail later in this file.

At present, SPL mostly uses a separate code path, but the function names
and roles of each function are the same. Some boards or architectures
may not conform to this.  At least most ARM boards which use
CONFIG_SPL_FRAMEWORK conform to this.

Execution typically starts with an architecture-specific (and possibly
CPU-specific) start.S file, such as:

	- arch/arm/cpu/armv7/start.S
	- arch/powerpc/cpu/mpc83xx/start.S
	- arch/mips/cpu/start.S
242

243 244
and so on. From there, three functions are called; the purpose and
limitations of each of these functions are described below.
245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302

lowlevel_init():
	- purpose: essential init to permit execution to reach board_init_f()
	- no global_data or BSS
	- there is no stack (ARMv7 may have one but it will soon be removed)
	- must not set up SDRAM or use console
	- must only do the bare minimum to allow execution to continue to
		board_init_f()
	- this is almost never needed
	- return normally from this function

board_init_f():
	- purpose: set up the machine ready for running board_init_r():
		i.e. SDRAM and serial UART
	- global_data is available
	- stack is in SRAM
	- BSS is not available, so you cannot use global/static variables,
		only stack variables and global_data

	Non-SPL-specific notes:
	- dram_init() is called to set up DRAM. If already done in SPL this
		can do nothing

	SPL-specific notes:
	- you can override the entire board_init_f() function with your own
		version as needed.
	- preloader_console_init() can be called here in extremis
	- should set up SDRAM, and anything needed to make the UART work
	- these is no need to clear BSS, it will be done by crt0.S
	- must return normally from this function (don't call board_init_r()
		directly)

Here the BSS is cleared. For SPL, if CONFIG_SPL_STACK_R is defined, then at
this point the stack and global_data are relocated to below
CONFIG_SPL_STACK_R_ADDR. For non-SPL, U-Boot is relocated to run at the top of
memory.

board_init_r():
	- purpose: main execution, common code
	- global_data is available
	- SDRAM is available
	- BSS is available, all static/global variables can be used
	- execution eventually continues to main_loop()

	Non-SPL-specific notes:
	- U-Boot is relocated to the top of memory and is now running from
		there.

	SPL-specific notes:
	- stack is optionally in SDRAM, if CONFIG_SPL_STACK_R is defined and
		CONFIG_SPL_STACK_R_ADDR points into SDRAM
	- preloader_console_init() can be called here - typically this is
		done by defining CONFIG_SPL_BOARD_INIT and then supplying a
		spl_board_init() function containing this call
	- loads U-Boot or (in falcon mode) Linux



wdenk's avatar
wdenk committed
303 304 305 306 307 308 309 310 311 312 313
Configuration Options:
----------------------

Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".

Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".


wdenk's avatar
wdenk committed
314 315 316 317 318
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.


wdenk's avatar
wdenk committed
319 320
The following options need to be configured:

321 322 323
- CPU Type:	Define exactly one, e.g. CONFIG_MPC85XX.

- Board Type:	Define exactly one, e.g. CONFIG_MPC8540ADS.
324 325

- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
326
		Define exactly one, e.g. CONFIG_ATSTK1002
wdenk's avatar
wdenk committed
327

328 329 330 331 332
- Marvell Family Member
		CONFIG_SYS_MVFS		- define it if you want to enable
					  multiple fs option at one time
					  for marvell soc family

333
- 8xx CPU Options: (if using an MPC8xx CPU)
334 335
		CONFIG_8xx_GCLK_FREQ	- deprecated: CPU clock if
					  get_gclk_freq() cannot work
336 337
					  e.g. if there is no 32KHz
					  reference PIT/RTC clock
338 339
		CONFIG_8xx_OSCLK	- PLL input clock (either EXTCLK
					  or XTAL/EXTAL)
wdenk's avatar
wdenk committed
340

341
- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
342 343
		CONFIG_SYS_8xx_CPUCLK_MIN
		CONFIG_SYS_8xx_CPUCLK_MAX
344
		CONFIG_8xx_CPUCLK_DEFAULT
345 346
			See doc/README.MPC866

347
		CONFIG_SYS_MEASURE_CPUCLK
348

349 350 351 352 353
		Define this to measure the actual CPU clock instead
		of relying on the correctness of the configured
		values. Mostly useful for board bringup to make sure
		the PLL is locked at the intended frequency. Note
		that this requires a (stable) reference clock (32 kHz
354
		RTC clock or CONFIG_SYS_8XX_XIN)
355

356 357 358 359 360
		CONFIG_SYS_DELAYED_ICACHE

		Define this option if you want to enable the
		ICache only when Code runs from RAM.

361
- 85xx CPU Options:
362 363 364 365 366 367
		CONFIG_SYS_PPC64

		Specifies that the core is a 64-bit PowerPC implementation (implements
		the "64" category of the Power ISA). This is necessary for ePAPR
		compliance, among other possible reasons.

368 369 370 371 372 373
		CONFIG_SYS_FSL_TBCLK_DIV

		Defines the core time base clock divider ratio compared to the
		system clock.  On most PQ3 devices this is 8, on newer QorIQ
		devices it can be 16 or 32.  The ratio varies from SoC to Soc.

374 375 376 377 378
		CONFIG_SYS_FSL_PCIE_COMPAT

		Defines the string to utilize when trying to match PCIe device
		tree nodes for the given platform.

379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398
		CONFIG_SYS_FSL_ERRATUM_A004510

		Enables a workaround for erratum A004510.  If set,
		then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.

		CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
		CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)

		Defines one or two SoC revisions (low 8 bits of SVR)
		for which the A004510 workaround should be applied.

		The rest of SVR is either not relevant to the decision
		of whether the erratum is present (e.g. p2040 versus
		p2041) or is implied by the build target, which controls
		whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.

		See Freescale App Note 4493 for more information about
		this erratum.

399 400
		CONFIG_A003399_NOR_WORKAROUND
		Enables a workaround for IFC erratum A003399. It is only
401
		required during NOR boot.
402

403 404
		CONFIG_A008044_WORKAROUND
		Enables a workaround for T1040/T1042 erratum A008044. It is only
405
		required during NAND boot and valid for Rev 1.0 SoC revision
406

407 408 409 410 411
		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY

		This is the value to write into CCSR offset 0x18600
		according to the A004510 workaround.

412 413 414 415
		CONFIG_SYS_FSL_DSP_DDR_ADDR
		This value denotes start offset of DDR memory which is
		connected exclusively to the DSP cores.

416 417 418 419
		CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
		This value denotes start offset of M2 memory
		which is directly connected to the DSP core.

420 421 422 423
		CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
		This value denotes start offset of M3 memory which is directly
		connected to the DSP core.

424 425 426
		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
		This value denotes start offset of DSP CCSR space.

427 428 429 430 431
		CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
		Single Source Clock is clocking mode present in some of FSL SoC's.
		In this mode, a single differential clock is used to supply
		clocks to the sysclock, ddrclock and usbclock.

432 433
		CONFIG_SYS_CPC_REINIT_F
		This CONFIG is defined when the CPC is configured as SRAM at the
434
		time of U-Boot entry and is required to be re-initialized.
435

436
		CONFIG_DEEP_SLEEP
437
		Indicates this SoC supports deep sleep feature. If deep sleep is
438 439
		supported, core will start to execute uboot when wakes up.

440
- Generic CPU options:
441 442 443 444 445 446
		CONFIG_SYS_GENERIC_GLOBAL_DATA
		Defines global data is initialized in generic board board_init_f().
		If this macro is defined, global data is created and cleared in
		generic board board_init_f(). Without this macro, architecture/board
		should initialize global data before calling board_init_f().

447 448 449 450 451
		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN

		Defines the endianess of the CPU. Implementation of those
		values is arch specific.

452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472
		CONFIG_SYS_FSL_DDR
		Freescale DDR driver in use. This type of DDR controller is
		found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
		SoCs.

		CONFIG_SYS_FSL_DDR_ADDR
		Freescale DDR memory-mapped register base.

		CONFIG_SYS_FSL_DDR_EMU
		Specify emulator support for DDR. Some DDR features such as
		deskew training are not available.

		CONFIG_SYS_FSL_DDRC_GEN1
		Freescale DDR1 controller.

		CONFIG_SYS_FSL_DDRC_GEN2
		Freescale DDR2 controller.

		CONFIG_SYS_FSL_DDRC_GEN3
		Freescale DDR3 controller.

473 474 475
		CONFIG_SYS_FSL_DDRC_GEN4
		Freescale DDR4 controller.

476 477 478
		CONFIG_SYS_FSL_DDRC_ARM_GEN3
		Freescale DDR3 controller for ARM-based SoCs.

479 480 481 482 483 484
		CONFIG_SYS_FSL_DDR1
		Board config to use DDR1. It can be enabled for SoCs with
		Freescale DDR1 or DDR2 controllers, depending on the board
		implemetation.

		CONFIG_SYS_FSL_DDR2
485
		Board config to use DDR2. It can be enabled for SoCs with
486 487 488 489 490
		Freescale DDR2 or DDR3 controllers, depending on the board
		implementation.

		CONFIG_SYS_FSL_DDR3
		Board config to use DDR3. It can be enabled for SoCs with
491 492 493 494 495 496 497 498 499
		Freescale DDR3 or DDR3L controllers.

		CONFIG_SYS_FSL_DDR3L
		Board config to use DDR3L. It can be enabled for SoCs with
		DDR3L controllers.

		CONFIG_SYS_FSL_DDR4
		Board config to use DDR4. It can be enabled for SoCs with
		DDR4 controllers.
500

501 502 503 504 505 506
		CONFIG_SYS_FSL_IFC_BE
		Defines the IFC controller register space as Big Endian

		CONFIG_SYS_FSL_IFC_LE
		Defines the IFC controller register space as Little Endian

507 508 509
		CONFIG_SYS_FSL_IFC_CLK_DIV
		Defines divider of platform clock(clock input to IFC controller).

510 511 512
		CONFIG_SYS_FSL_LBC_CLK_DIV
		Defines divider of platform clock(clock input to eLBC controller).

513 514 515 516 517 518 519 520 521
		CONFIG_SYS_FSL_PBL_PBI
		It enables addition of RCW (Power on reset configuration) in built image.
		Please refer doc/README.pblimage for more details

		CONFIG_SYS_FSL_PBL_RCW
		It adds PBI(pre-boot instructions) commands in u-boot build image.
		PBI commands can be used to configure SoC before it starts the execution.
		Please refer doc/README.pblimage for more details

522 523 524 525
		CONFIG_SPL_FSL_PBL
		It adds a target to create boot binary having SPL binary in PBI format
		concatenated with u-boot binary.

526 527 528 529 530 531
		CONFIG_SYS_FSL_DDR_BE
		Defines the DDR controller register space as Big Endian

		CONFIG_SYS_FSL_DDR_LE
		Defines the DDR controller register space as Little Endian

532 533 534 535 536
		CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
		Physical address from the view of DDR controllers. It is the
		same as CONFIG_SYS_DDR_SDRAM_BASE for  all Power SoCs. But
		it could be different for ARM SoCs.

537 538 539 540 541
		CONFIG_SYS_FSL_DDR_INTLV_256B
		DDR controller interleaving on 256-byte. This is a special
		interleaving mode, handled by Dickens for Freescale layerscape
		SoCs with ARM core.

542 543 544 545 546 547
		CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
		Number of controllers used as main memory.

		CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
		Number of controllers used for other than main memory.

548 549 550
		CONFIG_SYS_FSL_HAS_DP_DDR
		Defines the SoC has DP-DDR used for DPAA.

551 552 553 554 555 556
		CONFIG_SYS_FSL_SEC_BE
		Defines the SEC controller register space as Big Endian

		CONFIG_SYS_FSL_SEC_LE
		Defines the SEC controller register space as Little Endian

557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588
- MIPS CPU options:
		CONFIG_SYS_INIT_SP_OFFSET

		Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
		pointer. This is needed for the temporary stack before
		relocation.

		CONFIG_SYS_MIPS_CACHE_MODE

		Cache operation mode for the MIPS CPU.
		See also arch/mips/include/asm/mipsregs.h.
		Possible values are:
			CONF_CM_CACHABLE_NO_WA
			CONF_CM_CACHABLE_WA
			CONF_CM_UNCACHED
			CONF_CM_CACHABLE_NONCOHERENT
			CONF_CM_CACHABLE_CE
			CONF_CM_CACHABLE_COW
			CONF_CM_CACHABLE_CUW
			CONF_CM_CACHABLE_ACCELERATED

		CONFIG_SYS_XWAY_EBU_BOOTCFG

		Special option for Lantiq XWAY SoCs for booting from NOR flash.
		See also arch/mips/cpu/mips32/start.S.

		CONFIG_XWAY_SWAP_BYTES

		Enable compilation of tools/xway-swap-bytes needed for Lantiq
		XWAY SoCs for booting from NOR flash. The U-Boot image needs to
		be swapped if a flash programmer is used.

589 590 591 592 593 594
- ARM options:
		CONFIG_SYS_EXCEPTION_VECTORS_HIGH

		Select high exception vectors of the ARM core, e.g., do not
		clear the V bit of the c1 register of CP15.

Aneesh V's avatar
Aneesh V committed
595 596 597 598 599 600 601 602
		CONFIG_SYS_THUMB_BUILD

		Use this flag to build U-Boot using the Thumb instruction
		set for ARM architectures. Thumb instruction set provides
		better code density. For ARM architectures that support
		Thumb2 this flag will result in Thumb2 code generated by
		GCC.

603 604 605 606 607 608 609 610
		COUNTER_FREQUENCY
		Generic timer clock source frequency.

		COUNTER_FREQUENCY_REAL
		Generic timer clock source frequency if the real clock is
		different from COUNTER_FREQUENCY, and can only be determined
		at run time.

611 612 613 614 615 616 617
- Tegra SoC options:
		CONFIG_TEGRA_SUPPORT_NON_SECURE

		Support executing U-Boot in non-secure (NS) mode. Certain
		impossible actions will be skipped if the CPU is in NS mode,
		such as ARM architectural timer initialization.

618
- Linux Kernel Interface:
wdenk's avatar
wdenk committed
619 620 621 622 623 624 625 626 627 628
		CONFIG_CLOCKS_IN_MHZ

		U-Boot stores all clock information in Hz
		internally. For binary compatibility with older Linux
		kernels (which expect the clocks passed in the
		bd_info data to be in MHz) the environment variable
		"clocks_in_mhz" can be defined so that U-Boot
		converts clock data to MHZ before passing it to the
		Linux kernel.
		When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
629
		"clocks_in_mhz=1" is automatically included in the
wdenk's avatar
wdenk committed
630 631
		default environment.

632 633
		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]

634
		When transferring memsize parameter to Linux, some versions
635 636 637
		expect it to be in bytes, others in MB.
		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.

638
		CONFIG_OF_LIBFDT
639 640

		New kernel versions are expecting firmware settings to be
641 642 643 644 645 646
		passed using flattened device trees (based on open firmware
		concepts).

		CONFIG_OF_LIBFDT
		 * New libfdt-based support
		 * Adds the "fdt" command
647
		 * The bootm command automatically updates the fdt
648

649 650 651 652
		OF_CPU - The proper name of the cpus node (only required for
			MPC512X and MPC5xxx based boards).
		OF_SOC - The proper name of the soc node (only required for
			MPC512X and MPC5xxx based boards).
653
		OF_TBCLK - The timebase frequency.
654
		OF_STDOUT_PATH - The path to the console device
655

656 657
		boards with QUICC Engines require OF_QE to set UCC MAC
		addresses
658

659 660 661 662
		CONFIG_OF_BOARD_SETUP

		Board code has addition modification that it wants to make
		to the flat device tree before handing it off to the kernel
663

664 665 666 667 668 669 670
		CONFIG_OF_SYSTEM_SETUP

		Other code has addition modification that it wants to make
		to the flat device tree before handing it off to the kernel.
		This causes ft_system_setup() to be called before booting
		the kernel.

671 672 673 674 675 676 677 678 679
		CONFIG_OF_IDE_FIXUP

		U-Boot can detect if an IDE device is present or not.
		If not, and this new config option is activated, U-Boot
		removes the ATA node from the DTS before booting Linux,
		so the Linux IDE driver does not probe the device and
		crash. This is needed for buggy hardware (uc101) where
		no pull down resistor is connected to the signal IDE5V_DD7.

680 681 682 683 684 685 686 687 688 689
		CONFIG_MACH_TYPE	[relevant for ARM only][mandatory]

		This setting is mandatory for all boards that have only one
		machine type and must be used to specify the machine type
		number as it appears in the ARM machine registry
		(see http://www.arm.linux.org.uk/developer/machines/).
		Only boards that have multiple machine types supported
		in a single configuration file and the machine type is
		runtime discoverable, do not have to use this setting.

690 691 692
- vxWorks boot parameters:

		bootvx constructs a valid bootline using the following
693 694
		environments variables: bootdev, bootfile, ipaddr, netmask,
		serverip, gatewayip, hostname, othbootargs.
695 696 697 698 699
		It loads the vxWorks image pointed bootfile.

		Note: If a "bootargs" environment is defined, it will overwride
		the defaults discussed just above.

700 701 702 703 704
- Cache Configuration:
		CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
		CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
		CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot

705 706 707 708 709 710
- Cache Configuration for ARM:
		CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
				      controller
		CONFIG_SYS_PL310_BASE - Physical base address of PL310
					controller register space

711
- Serial Ports:
712
		CONFIG_PL010_SERIAL
713 714 715

		Define this if you want support for Amba PrimeCell PL010 UARTs.

716
		CONFIG_PL011_SERIAL
717 718 719 720 721 722 723 724 725 726 727 728 729 730

		Define this if you want support for Amba PrimeCell PL011 UARTs.

		CONFIG_PL011_CLOCK

		If you have Amba PrimeCell PL011 UARTs, set this variable to
		the clock speed of the UARTs.

		CONFIG_PL01x_PORTS

		If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
		define this to a list of base addresses for each (supported)
		port. See e.g. include/configs/versatile.h

731 732 733 734
		CONFIG_SERIAL_HW_FLOW_CONTROL

		Define this variable to enable hw flow control in serial driver.
		Current user of this option is drivers/serial/nsl16550.c driver
735

wdenk's avatar
wdenk committed
736
- Console Interface:
737 738 739 740
		Depending on board, define exactly one serial port
		(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
		CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
		console by defining CONFIG_8xx_CONS_NONE
wdenk's avatar
wdenk committed
741 742 743 744 745 746 747 748

		Note: if CONFIG_8xx_CONS_NONE is defined, the serial
		port routines must be defined elsewhere
		(i.e. serial_init(), serial_getc(), ...)

- Console Baudrate:
		CONFIG_BAUDRATE - in bps
		Select one of the baudrates listed in
749 750
		CONFIG_SYS_BAUDRATE_TABLE, see below.
		CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
wdenk's avatar
wdenk committed
751

752 753 754
- Console Rx buffer length
		With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
		the maximum receive buffer length for the SMC.
755
		This option is actual only for 82xx and 8xx possible.
756 757 758 759
		If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
		must be defined, to setup the maximum idle timeout for
		the SMC.

wdenk's avatar
wdenk committed
760 761 762 763 764 765 766 767
- Autoboot Command:
		CONFIG_BOOTCOMMAND
		Only needed when CONFIG_BOOTDELAY is enabled;
		define a command string that is automatically executed
		when no character is read on the console interface
		within "Boot Delay" after reset.

		CONFIG_BOOTARGS
768 769 770
		This can be used to pass arguments to the bootm
		command. The value of CONFIG_BOOTARGS goes into the
		environment value "bootargs".
wdenk's avatar
wdenk committed
771 772

		CONFIG_RAMBOOT and CONFIG_NFSBOOT
773 774 775
		The value of these goes into the environment as
		"ramboot" and "nfsboot" respectively, and can be used
		as a convenience, when switching between booting from
776
		RAM and NFS.
wdenk's avatar
wdenk committed
777

778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793
- Bootcount:
		CONFIG_BOOTCOUNT_LIMIT
		Implements a mechanism for detecting a repeating reboot
		cycle, see:
		http://www.denx.de/wiki/view/DULG/UBootBootCountLimit

		CONFIG_BOOTCOUNT_ENV
		If no softreset save registers are found on the hardware
		"bootcount" is stored in the environment. To prevent a
		saveenv on all reboots, the environment variable
		"upgrade_available" is used. If "upgrade_available" is
		0, "bootcount" is always 0, if "upgrade_available" is
		1 "bootcount" is incremented in the environment.
		So the Userspace Applikation must set the "upgrade_available"
		and "bootcount" variable to 0, if a boot was successfully.

wdenk's avatar
wdenk committed
794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818
- Pre-Boot Commands:
		CONFIG_PREBOOT

		When this option is #defined, the existence of the
		environment variable "preboot" will be checked
		immediately before starting the CONFIG_BOOTDELAY
		countdown and/or running the auto-boot command resp.
		entering interactive mode.

		This feature is especially useful when "preboot" is
		automatically generated or modified. For an example
		see the LWMON board specific code: here "preboot" is
		modified when the user holds down a certain
		combination of keys on the (special) keyboard when
		booting the systems

- Serial Download Echo Mode:
		CONFIG_LOADS_ECHO
		If defined to 1, all characters received during a
		serial download (using the "loads" command) are
		echoed back. This might be needed by some terminal
		emulations (like "cu"), but may as well just take
		time on others. This setting #define's the initial
		value of the "loads_echo" environment variable.

819
- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
wdenk's avatar
wdenk committed
820 821
		CONFIG_KGDB_BAUDRATE
		Select one of the baudrates listed in
822
		CONFIG_SYS_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
823 824

- Monitor Functions:
825 826
		Monitor commands can be included or excluded
		from the build by using the #include files
827
		<config_cmd_all.h> and #undef'ing unwanted
828
		commands, or adding #define's for wanted commands.
829 830 831 832

		The default command configuration includes all commands
		except those marked below with a "*".

833
		CONFIG_CMD_AES		  AES 128 CBC encrypt/decrypt
834 835 836 837 838 839
		CONFIG_CMD_ASKENV	* ask for env variable
		CONFIG_CMD_BDI		  bdinfo
		CONFIG_CMD_BEDBUG	* Include BedBug Debugger
		CONFIG_CMD_BMP		* BMP support
		CONFIG_CMD_BSP		* Board specific commands
		CONFIG_CMD_BOOTD	  bootd
840
		CONFIG_CMD_BOOTI	* ARM64 Linux kernel Image support
841
		CONFIG_CMD_CACHE	* icache, dcache
842
		CONFIG_CMD_CLK   	* clock command support
843
		CONFIG_CMD_CONSOLE	  coninfo
844
		CONFIG_CMD_CRC32	* crc32
845 846 847
		CONFIG_CMD_DATE		* support for RTC, date/time...
		CONFIG_CMD_DHCP		* DHCP support
		CONFIG_CMD_DIAG		* Diagnostics
848 849 850 851
		CONFIG_CMD_DS4510	* ds4510 I2C gpio commands
		CONFIG_CMD_DS4510_INFO	* ds4510 I2C info command
		CONFIG_CMD_DS4510_MEM	* ds4510 I2C eeprom/sram commansd
		CONFIG_CMD_DS4510_RST	* ds4510 I2C rst command
852 853
		CONFIG_CMD_DTT		* Digital Therm and Thermostat
		CONFIG_CMD_ECHO		  echo arguments
Peter Tyser's avatar
Peter Tyser committed
854
		CONFIG_CMD_EDITENV	  edit env variable
855
		CONFIG_CMD_EEPROM	* EEPROM read/write support
856
		CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
857
		CONFIG_CMD_ELF		* bootelf, bootvx
858
		CONFIG_CMD_ENV_CALLBACK	* display details about env callbacks
859
		CONFIG_CMD_ENV_FLAGS	* display details about env flags
860
		CONFIG_CMD_ENV_EXISTS	* check existence of env variable
861
		CONFIG_CMD_EXPORTENV	* export the environment
862 863
		CONFIG_CMD_EXT2		* ext2 command support
		CONFIG_CMD_EXT4		* ext4 command support
864 865
		CONFIG_CMD_FS_GENERIC	* filesystem commands (e.g. load, ls)
					  that work for multiple fs types
866
		CONFIG_CMD_FS_UUID	* Look up a filesystem UUID
867
		CONFIG_CMD_SAVEENV	  saveenv
868
		CONFIG_CMD_FDC		* Floppy Disk Support
869
		CONFIG_CMD_FAT		* FAT command support
870 871
		CONFIG_CMD_FLASH	  flinfo, erase, protect
		CONFIG_CMD_FPGA		  FPGA device initialization support
872
		CONFIG_CMD_FUSE		* Device fuse support
Anton Staaf's avatar
Anton Staaf committed
873
		CONFIG_CMD_GETTIME	* Get time since boot
Mike Frysinger's avatar
Mike Frysinger committed
874
		CONFIG_CMD_GO		* the 'go' command (exec code)
875
		CONFIG_CMD_GREPENV	* search environment
876
		CONFIG_CMD_HASH		* calculate hash / digest
877 878 879
		CONFIG_CMD_I2C		* I2C serial bus support
		CONFIG_CMD_IDE		* IDE harddisk support
		CONFIG_CMD_IMI		  iminfo
880
		CONFIG_CMD_IMLS		  List all images found in NOR flash
881
		CONFIG_CMD_IMLS_NAND	* List all images found in NAND flash
882
		CONFIG_CMD_IMMAP	* IMMR dump support
Simon Glass's avatar
Simon Glass committed
883
		CONFIG_CMD_IOTRACE	* I/O tracing for debugging
884
		CONFIG_CMD_IMPORTENV	* import an environment
885
		CONFIG_CMD_INI		* import data from an ini file into the env
886 887 888 889
		CONFIG_CMD_IRQ		* irqinfo
		CONFIG_CMD_ITEST	  Integer/string test of 2 values
		CONFIG_CMD_JFFS2	* JFFS2 Support
		CONFIG_CMD_KGDB		* kgdb
890
		CONFIG_CMD_LDRINFO	* ldrinfo (display Blackfin loader)
891 892
		CONFIG_CMD_LINK_LOCAL	* link-local IP address auto-configuration
					  (169.254.*.*)
893 894
		CONFIG_CMD_LOADB	  loadb
		CONFIG_CMD_LOADS	  loads
895
		CONFIG_CMD_MD5SUM	* print md5 message digest
896
					  (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
897
		CONFIG_CMD_MEMINFO	* Display detailed memory information
898
		CONFIG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
899
					  loop, loopw
900
		CONFIG_CMD_MEMTEST	* mtest
901 902 903
		CONFIG_CMD_MISC		  Misc functions like sleep etc
		CONFIG_CMD_MMC		* MMC memory mapped support
		CONFIG_CMD_MII		* MII utility commands
904
		CONFIG_CMD_MTDPARTS	* MTD partition support
905 906
		CONFIG_CMD_NAND		* NAND support
		CONFIG_CMD_NET		  bootp, tftpboot, rarpboot
907
		CONFIG_CMD_NFS		  NFS support
908
		CONFIG_CMD_PCA953X	* PCA953x I2C gpio commands
909
		CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
910 911 912 913 914
		CONFIG_CMD_PCI		* pciinfo
		CONFIG_CMD_PCMCIA		* PCMCIA support
		CONFIG_CMD_PING		* send ICMP ECHO_REQUEST to network
					  host
		CONFIG_CMD_PORTIO	* Port I/O
915
		CONFIG_CMD_READ		* Read raw data from partition
916 917
		CONFIG_CMD_REGINFO	* Register dump
		CONFIG_CMD_RUN		  run command in env variable
918
		CONFIG_CMD_SANDBOX	* sb command to access sandbox features
919
		CONFIG_CMD_SAVES	* save S record dump
920
		CONFIG_SCSI		* SCSI Support
921 922 923 924
		CONFIG_CMD_SDRAM	* print SDRAM configuration information
					  (requires CONFIG_CMD_I2C)
		CONFIG_CMD_SETGETDCR	  Support for DCR Register access
					  (4xx only)
925
		CONFIG_CMD_SF		* Read/write/erase SPI NOR flash
926
		CONFIG_CMD_SHA1SUM	* print sha1 memory digest
927
					  (requires CONFIG_CMD_MEMORY)
928
		CONFIG_CMD_SOFTSWITCH	* Soft switch setting command for BF60x
929
		CONFIG_CMD_SOURCE	  "source" command Support
930
		CONFIG_CMD_SPI		* SPI serial bus support
931
		CONFIG_CMD_TFTPSRV	* TFTP transfer in server mode
932
		CONFIG_CMD_TFTPPUT	* TFTP put command (upload)
933 934
		CONFIG_CMD_TIME		* run command and report execution time (ARM specific)
		CONFIG_CMD_TIMER	* access to the system tick timer
935 936
		CONFIG_CMD_USB		* USB support
		CONFIG_CMD_CDP		* Cisco Discover Protocol support
937
		CONFIG_CMD_MFSL		* Microblaze FSL support
938
		CONFIG_CMD_XIMG		  Load part of Multi Image
939
		CONFIG_CMD_UUID		* Generate random UUID or GUID string
wdenk's avatar
wdenk committed
940 941 942 943

		EXAMPLE: If you want all functions except of network
		support you can write:

944 945
		#include "config_cmd_all.h"
		#undef CONFIG_CMD_NET
wdenk's avatar
wdenk committed
946

947 948
	Other Commands:
		fdt (flattened device tree) command: CONFIG_OF_LIBFDT
wdenk's avatar
wdenk committed
949 950

	Note:	Don't enable the "icache" and "dcache" commands
951
		(configuration option CONFIG_CMD_CACHE) unless you know
952 953 954 955 956 957
		what you (and your U-Boot users) are doing. Data
		cache cannot be enabled on systems like the 8xx or
		8260 (where accesses to the IMMR region must be
		uncached), and it cannot be disabled on all other
		systems where we (mis-) use the data cache to hold an
		initial stack and some data.
wdenk's avatar
wdenk committed
958 959 960 961


		XXX - this list needs to get updated!

962 963 964 965 966 967 968 969
- Removal of commands
		If no commands are needed to boot, you can disable
		CONFIG_CMDLINE to remove them. In this case, the command line
		will not be available, and when U-Boot wants to execute the
		boot command (on start-up) it will call board_run_command()
		instead. This can reduce image size significantly for very
		simple boot procedures.

970 971
- Regular expression support:
		CONFIG_REGEX
972 973 974 975
		If this variable is defined, U-Boot is linked against
		the SLRE (Super Light Regular Expression) library,
		which adds regex support to some commands, as for
		example "env grep" and "setexpr".
976

977 978 979 980 981 982 983 984
- Device tree:
		CONFIG_OF_CONTROL
		If this variable is defined, U-Boot will use a device tree
		to configure its devices, instead of relying on statically
		compiled #defines in the board file. This option is
		experimental and only available on a few boards. The device
		tree is available in the global data as gd->fdt_blob.

985 986
		U-Boot needs to get its device tree from somewhere. This can
		be done using one of the two options below:
987 988 989 990 991 992 993

		CONFIG_OF_EMBED
		If this variable is defined, U-Boot will embed a device tree
		binary in its image. This device tree file should be in the
		board directory and called <soc>-<board>.dts. The binary file
		is then picked up in board_init_f() and made available through
		the global data structure as gd->blob.
994

995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006
		CONFIG_OF_SEPARATE
		If this variable is defined, U-Boot will build a device tree
		binary. It will be called u-boot.dtb. Architecture-specific
		code will locate it at run-time. Generally this works by:

			cat u-boot.bin u-boot.dtb >image.bin

		and in fact, U-Boot does this for you, creating a file called
		u-boot-dtb.bin which is useful in the common case. You can
		still use the individual files if you need something more
		exotic.

wdenk's avatar
wdenk committed
1007 1008 1009
- Watchdog:
		CONFIG_WATCHDOG
		If this variable is defined, it enables watchdog
1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020
		support for the SoC. There must be support in the SoC
		specific code for a watchdog. For the 8xx and 8260
		CPUs, the SIU Watchdog feature is enabled in the SYPCR
		register.  When supported for a specific SoC is
		available, then no further board specific code should
		be needed to use it.

		CONFIG_HW_WATCHDOG
		When using a watchdog circuitry external to the used
		SoC, then define this variable and provide board
		specific code for the "hw_watchdog_reset" function.
wdenk's avatar
wdenk committed
1021

1022 1023 1024
		CONFIG_AT91_HW_WDT_TIMEOUT
		specify the timeout in seconds. default 2 seconds.

1025 1026 1027 1028 1029
- U-Boot Version:
		CONFIG_VERSION_VARIABLE
		If this variable is defined, an environment variable
		named "ver" is created by U-Boot showing the U-Boot
		version as printed by the "version" command.
1030 1031
		Any change to this variable will be reverted at the
		next reset.
1032

wdenk's avatar
wdenk committed
1033 1034
- Real-Time Clock:

1035
		When CONFIG_CMD_DATE is selected, the type of the RTC
wdenk's avatar
wdenk committed
1036 1037 1038 1039 1040
		has to be selected, too. Define exactly one of the
		following options:

		CONFIG_RTC_MPC8xx	- use internal RTC of MPC8xx
		CONFIG_RTC_PCF8563	- use Philips PCF8563 RTC
1041
		CONFIG_RTC_MC13XXX	- use MC13783 or MC13892 RTC
wdenk's avatar
wdenk committed
1042
		CONFIG_RTC_MC146818	- use MC146818 RTC
1043
		CONFIG_RTC_DS1307	- use Maxim, Inc. DS1307 RTC
wdenk's avatar
wdenk committed
1044
		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
1045
		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
1046
		CONFIG_RTC_DS1339	- use Maxim, Inc. DS1339 RTC
1047
		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
1048
		CONFIG_RTC_ISL1208	- use Intersil ISL1208 RTC
1049
		CONFIG_RTC_MAX6900	- use Maxim, Inc. MAX6900 RTC
1050
		CONFIG_SYS_RTC_DS1337_NOOSC	- Turn off the OSC output for DS1337
1051 1052
		CONFIG_SYS_RV3029_TCR	- enable trickle charger on
					  RV3029 RTC.
wdenk's avatar
wdenk committed
1053

1054 1055 1056
		Note that if the RTC uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

1057 1058 1059
- GPIO Support:
		CONFIG_PCA953X		- use NXP's PCA953X series I2C GPIO

1060 1061 1062 1063
		The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
		chip-ngpio pairs that tell the PCA953X driver the number of
		pins supported by a particular chip.

1064 1065 1066
		Note that if the GPIO device uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

Simon Glass's avatar
Simon Glass committed
1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088
- I/O tracing:
		When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
		accesses and can checksum them or write a list of them out
		to memory. See the 'iotrace' command for details. This is
		useful for testing device drivers since it can confirm that
		the driver behaves the same way before and after a code
		change. Currently this is supported on sandbox and arm. To
		add support for your architecture, add '#include <iotrace.h>'
		to the bottom of arch/<arch>/include/asm/io.h and test.

		Example output from the 'iotrace stats' command is below.
		Note that if the trace buffer is exhausted, the checksum will
		still continue to operate.

			iotrace is enabled
			Start:  10000000	(buffer start address)
			Size:   00010000	(buffer size)
			Offset: 00000120	(current buffer offset)
			Output: 10000120	(start + offset)
			Count:  00000018	(number of trace records)
			CRC32:  9526fb66	(CRC32 of all trace records)

wdenk's avatar
wdenk committed
1089 1090
- Timestamp Support:

1091 1092 1093
		When CONFIG_TIMESTAMP is selected, the timestamp
		(date and time) of an image is printed by image
		commands like bootm or iminfo. This option is
1094
		automatically enabled when you select CONFIG_CMD_DATE .
wdenk's avatar
wdenk committed
1095

1096 1097 1098 1099 1100 1101 1102 1103 1104 1105
- Partition Labels (disklabels) Supported:
		Zero or more of the following:
		CONFIG_MAC_PARTITION   Apple's MacOS partition table.
		CONFIG_DOS_PARTITION   MS Dos partition table, traditional on the
				       Intel architecture, USB sticks, etc.
		CONFIG_ISO_PARTITION   ISO partition table, used on CDROM etc.
		CONFIG_EFI_PARTITION   GPT partition table, common when EFI is the
				       bootloader.  Note 2TB partition limit; see
				       disk/part_efi.c
		CONFIG_MTD_PARTITIONS  Memory Technology Device partition table.
wdenk's avatar
wdenk committed
1106

1107
		If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1108
		CONFIG_SCSI) you must configure support for at
1109
		least one non-MTD partition type as well.
wdenk's avatar
wdenk committed
1110 1111

- IDE Reset method:
1112 1113
		CONFIG_IDE_RESET_ROUTINE - this is defined in several
		board configurations files but used nowhere!
wdenk's avatar
wdenk committed
1114

1115 1116 1117 1118
		CONFIG_IDE_RESET - is this is defined, IDE Reset will
		be performed by calling the function
			ide_set_reset(int reset)
		which has to be defined in a board specific file
wdenk's avatar
wdenk committed
1119 1120 1121 1122 1123 1124

- ATAPI Support:
		CONFIG_ATAPI

		Set this to enable ATAPI support.

1125 1126 1127 1128
- LBA48 Support
		CONFIG_LBA48

		Set this to enable support for disks larger than 137GB
1129
		Also look at CONFIG_SYS_64BIT_LBA.
1130 1131 1132
		Whithout these , LBA48 support uses 32bit variables and will 'only'
		support disks up to 2.1TB.

1133
		CONFIG_SYS_64BIT_LBA:
1134 1135 1136
			When enabled, makes the IDE subsystem use 64bit sector addresses.
			Default is 32bit.

wdenk's avatar
wdenk committed
1137 1138 1139 1140 1141
- SCSI Support:
		At the moment only there is only support for the
		SYM53C8XX SCSI controller; define
		CONFIG_SCSI_SYM53C8XX to enable it.

1142 1143 1144
		CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
		CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
		CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
wdenk's avatar
wdenk committed
1145 1146
		maximum numbers of LUNs, SCSI ID's and target
		devices.
1147
		CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
wdenk's avatar
wdenk committed
1148

1149 1150
		The environment variable 'scsidevs' is set to the number of
		SCSI devices found during the last scan.
1151

wdenk's avatar
wdenk committed
1152
- NETWORK Support (PCI):
1153
		CONFIG_E1000
1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167
		Support for Intel 8254x/8257x gigabit chips.

		CONFIG_E1000_SPI
		Utility code for direct access to the SPI bus on Intel 8257x.
		This does not do anything useful unless you set at least one
		of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.

		CONFIG_E1000_SPI_GENERIC
		Allow generic access to the SPI bus on the Intel 8257x, for
		example with the "sspi" command.

		CONFIG_CMD_E1000
		Management command for E1000 devices.  When used on devices
		with SPI support you can reprogram the EEPROM from U-Boot.
stroese's avatar
stroese committed
1168

wdenk's avatar
wdenk committed
1169 1170
		CONFIG_EEPRO100
		Support for Intel 82557/82559/82559ER chips.
1171
		Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
wdenk's avatar
wdenk committed
1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184
		write routine for first time initialisation.

		CONFIG_TULIP
		Support for Digital 2114x chips.
		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
		modem chip initialisation (KS8761/QS6611).

		CONFIG_NATSEMI
		Support for National dp83815 chips.

		CONFIG_NS8382X
		Support for National dp8382[01] gigabit chips.

1185 1186
- NETWORK Support (other):

1187 1188 1189 1190 1191 1192 1193 1194 1195 1196
		CONFIG_DRIVER_AT91EMAC
		Support for AT91RM9200 EMAC.

			CONFIG_RMII
			Define this to use reduced MII inteface

			CONFIG_DRIVER_AT91EMAC_QUIET
			If this defined, the driver is quiet.
			The driver doen't show link status messages.

1197 1198 1199
		CONFIG_CALXEDA_XGMAC
		Support for the Calxeda XGMAC device

1200
		CONFIG_LAN91C96
1201 1202 1203 1204 1205
		Support for SMSC's LAN91C96 chips.

			CONFIG_LAN91C96_USE_32_BIT
			Define this to enable 32 bit addressing

1206
		CONFIG_SMC91111
1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219
		Support for SMSC's LAN91C111 chip

			CONFIG_SMC91111_BASE
			Define this to hold the physical address
			of the device (I/O space)

			CONFIG_SMC_USE_32_BIT
			Define this if data bus is 32 bits

			CONFIG_SMC_USE_IOFUNCS
			Define this to use i/o functions instead of macros
			(some hardware wont work with macros)

1220 1221 1222 1223 1224 1225
		CONFIG_DRIVER_TI_EMAC
		Support for davinci emac

			CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
			Define this if you have more then 3 PHYs.

1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237
		CONFIG_FTGMAC100
		Support for Faraday's FTGMAC100 Gigabit SoC Ethernet

			CONFIG_FTGMAC100_EGIGA
			Define this to use GE link update with gigabit PHY.
			Define this if FTGMAC100 is connected to gigabit PHY.
			If your system has 10/100 PHY only, it might not occur
			wrong behavior. Because PHY usually return timeout or
			useless data when polling gigabit status and gigabit
			control registers. This behavior won't affect the
			correctnessof 10/100 link speed update.

1238
		CONFIG_SMC911X
1239 1240
		Support for SMSC's LAN911x and LAN921x chips

1241
			CONFIG_SMC911X_BASE
1242 1243 1244
			Define this to hold the physical address
			of the device (I/O space)

1245
			CONFIG_SMC911X_32_BIT
1246 1247
			Define this if data bus is 32 bits

1248
			CONFIG_SMC911X_16_BIT
1249 1250
			Define this if data bus is 16 bits. If your processor
			automatically converts one 32 bit word to two 16 bit
1251
			words you may also try CONFIG_SMC911X_32_BIT.
1252

1253 1254 1255 1256 1257 1258 1259 1260 1261
		CONFIG_SH_ETHER
		Support for Renesas on-chip Ethernet controller

			CONFIG_SH_ETHER_USE_PORT
			Define the number of ports to be used

			CONFIG_SH_ETHER_PHY_ADDR
			Define the ETH PHY's address

1262 1263 1264
			CONFIG_SH_ETHER_CACHE_WRITEBACK
			If this option is set, the driver enables cache flush.

1265 1266
- PWM Support:
		CONFIG_PWM_IMX
1267
		Support for PWM module on the imx6.
1268

1269
- TPM Support:
1270 1271 1272
		CONFIG_TPM
		Support TPM devices.

1273 1274
		CONFIG_TPM_TIS_INFINEON
		Support for Infineon i2c bus TPM devices. Only one device
1275 1276 1277 1278 1279
		per system is supported at this time.

			CONFIG_TPM_TIS_I2C_BURST_LIMITATION
			Define the burst count bytes upper limit

1280 1281 1282 1283 1284 1285 1286
		CONFIG_TPM_ST33ZP24
		Support for STMicroelectronics TPM devices. Requires DM_TPM support.

			CONFIG_TPM_ST33ZP24_I2C
			Support for STMicroelectronics ST33ZP24 I2C devices.
			Requires TPM_ST33ZP24 and I2C.

1287 1288 1289 1290
			CONFIG_TPM_ST33ZP24_SPI
			Support for STMicroelectronics ST33ZP24 SPI devices.
			Requires TPM_ST33ZP24 and SPI.

Dirk Eibach's avatar
Dirk Eibach committed
1291 1292 1293
		CONFIG_TPM_ATMEL_TWI
		Support for Atmel TWI TPM device. Requires I2C support.

1294
		CONFIG_TPM_TIS_LPC
1295 1296 1297 1298 1299 1300 1301 1302
		Support for generic parallel port TPM devices. Only one device
		per system is supported at this time.

			CONFIG_TPM_TIS_BASE_ADDRESS
			Base address where the generic TPM device is mapped
			to. Contemporary x86 systems usually map it at
			0xfed40000.

1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316
		CONFIG_CMD_TPM
		Add tpm monitor functions.
		Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
		provides monitor access to authorized functions.

		CONFIG_TPM
		Define this to enable the TPM support library which provides
		functional interfaces to some TPM commands.
		Requires support for a TPM device.

		CONFIG_TPM_AUTH_SESSIONS
		Define this to enable authorized functions in the TPM library.
		Requires CONFIG_TPM and CONFIG_SHA1.

wdenk's avatar
wdenk committed
1317 1318
- USB Support:
		At the moment only the UHCI host controller is
1319
		supported (PIP405, MIP405, MPC5200); define
wdenk's avatar
wdenk committed
1320 1321
		CONFIG_USB_UHCI to enable it.
		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1322
		and define CONFIG_USB_STORAGE to enable the USB
wdenk's avatar
wdenk committed
1323 1324 1325 1326
		storage devices.
		Note:
		Supported are USB Keyboards and USB Floppy drives
		(TEAC FD-05PUB).
1327 1328 1329
		MPC5200 USB requires additional defines:
			CONFIG_USB_CLOCK
				for 528 MHz Clock: 0x0001bbbb
1330 1331
			CONFIG_PSC3_USB
				for USB on PSC3
1332 1333 1334
			CONFIG_USB_CONFIG
				for differential drivers: 0x00001000
				for single ended drivers: 0x00005000
1335 1336
				for differential drivers on PSC3: 0x00000100
				for single ended drivers on PSC3: 0x00004100
1337
			CONFIG_SYS_USB_EVENT_POLL
Zhang Wei's avatar
Zhang Wei committed
1338 1339
				May be defined to allow interrupt polling
				instead of using asynchronous interrupts
1340

1341 1342 1343
		CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
		txfilltuning field in the EHCI controller on reset.

1344 1345 1346
		CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
		HW module registers.

1347 1348 1349 1350
- USB Device:
		Define the below if you wish to use the USB console.
		Once firmware is rebuilt from a serial console issue the
		command "setenv stdin usbtty; setenv stdout usbtty" and
1351
		attach your USB cable. The Unix command "dmesg" should print
1352 1353
		it has found a new device. The environment variable usbtty
		can be set to gserial or cdc_acm to enable your device to
Wolfgang Denk's avatar
Wolfgang Denk committed
1354
		appear to a USB host as a Linux gserial device or a
1355 1356 1357 1358 1359 1360 1361
		Common Device Class Abstract Control Model serial device.
		If you select usbtty = gserial you should be able to enumerate
		a Linux host by
		# modprobe usbserial vendor=0xVendorID product=0xProductID
		else if using cdc_acm, simply setting the environment
		variable usbtty to be cdc_acm should suffice. The following
		might be defined in YourBoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
1362

1363 1364 1365 1366 1367 1368
			CONFIG_USB_DEVICE
			Define this to build a UDC device

			CONFIG_USB_TTY
			Define this to have a tty type of device available to
			talk to the UDC device
Wolfgang Denk's avatar
Wolfgang Denk committed
1369

1370 1371 1372 1373 1374 1375 1376 1377
			CONFIG_USBD_HS
			Define this to enable the high speed support for usb
			device and usbtty. If this feature is enabled, a routine
			int is_usbd_high_speed(void)
			also needs to be defined by the driver to dynamically poll
			whether the enumeration has succeded at high speed or full
			speed.

1378
			CONFIG_SYS_CONSOLE_IS_IN_ENV
1379 1380 1381 1382
			Define this if you want stdin, stdout &/or stderr to
			be set to usbtty.

			mpc8xx:
1383
				CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1384
				Derive USB clock from external clock "blah"
1385
				- CONFIG_SYS_USB_EXTC_CLK 0x02
Wolfgang Denk's avatar
Wolfgang Denk committed
1386 1387

		If you have a USB-IF assigned VendorID then you may wish to
1388
		define your own vendor specific values either in BoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
1389
		or directly in usbd_vendor_info.h. If you don't define
1390 1391 1392 1393 1394 1395 1396
		CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
		CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
		should pretend to be a Linux device to it's target host.

			CONFIG_USBD_MANUFACTURER
			Define this string as the name of your company for
			- CONFIG_USBD_MANUFACTURER "my company"
Wolfgang Denk's avatar
Wolfgang Denk committed
1397

1398 1399 1400 1401 1402 1403 1404 1405 1406
			CONFIG_USBD_PRODUCT_NAME
			Define this string as the name of your product
			- CONFIG_USBD_PRODUCT_NAME "acme usb device"

			CONFIG_USBD_VENDORID
			Define this as your assigned Vendor ID from the USB
			Implementors Forum. This *must* be a genuine Vendor ID
			to avoid polluting the USB namespace.
			- CONFIG_USBD_VENDORID 0xFFFF
Wolfgang Denk's avatar
Wolfgang Denk committed
1407

1408 1409 1410 1411
			CONFIG_USBD_PRODUCTID
			Define this as the unique Product ID
			for your device
			- CONFIG_USBD_PRODUCTID 0xFFFF
1412

1413 1414 1415 1416 1417 1418 1419 1420
- ULPI Layer Support:
		The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
		the generic ULPI layer. The generic layer accesses the ULPI PHY
		via the platform viewport, so you need both the genric layer and
		the viewport enabled. Currently only Chipidea/ARC based
		viewport is supported.
		To enable the ULPI layer support, define CONFIG_USB_ULPI and
		CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1421 1422 1423
		If your ULPI phy needs a different reference clock than the
		standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
		the appropriate value in Hz.
wdenk's avatar
wdenk committed
1424

1425
- MMC Support:
wdenk's avatar
wdenk committed
1426 1427 1428
		The MMC controller on the Intel PXA is supported. To
		enable this define CONFIG_MMC. The MMC can be
		accessed from the boot prompt by mapping the device
1429
		to physical memory similar to flash. Command line is
1430 1431
		enabled with CONFIG_CMD_MMC. The MMC driver also works with
		the FAT fs. This is enabled with CONFIG_CMD_FAT.
1432

1433 1434 1435 1436 1437 1438 1439 1440 1441
		CONFIG_SH_MMCIF
		Support for Renesas on-chip MMCIF controller

			CONFIG_SH_MMCIF_ADDR
			Define the base address of MMCIF registers

			CONFIG_SH_MMCIF_CLK
			Define the clock frequency for MMCIF

1442 1443 1444 1445 1446 1447 1448
		CONFIG_SUPPORT_EMMC_BOOT
		Enable some additional features of the eMMC boot partitions.

		CONFIG_SUPPORT_EMMC_RPMB
		Enable the commands for reading, writing and programming the
		key for the Replay Protection Memory Block partition in eMMC.

1449
- USB Device Firmware Update (DFU) class support:
1450
		CONFIG_USB_FUNCTION_DFU
1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461
		This enables the USB portion of the DFU USB class

		CONFIG_CMD_DFU
		This enables the command "dfu" which is used to have
		U-Boot create a DFU class device via USB.  This command
		requires that the "dfu_alt_info" environment variable be
		set and define the alt settings to expose to the host.

		CONFIG_DFU_MMC
		This enables support for exposing (e)MMC devices via DFU.

1462 1463 1464
		CONFIG_DFU_NAND
		This enables support for exposing NAND devices via DFU.

Afzal Mohammed's avatar
Afzal Mohammed committed
1465 1466 1467 1468 1469 1470
		CONFIG_DFU_RAM
		This enables support for exposing RAM via DFU.
		Note: DFU spec refer to non-volatile memory usage, but
		allow usages beyond the scope of spec - here RAM usage,
		one that would help mostly the developer.

1471 1472 1473 1474 1475 1476
		CONFIG_SYS_DFU_DATA_BUF_SIZE
		Dfu transfer uses a buffer before writing data to the
		raw storage device. Make the size (in bytes) of this buffer
		configurable. The size of this buffer is also configurable
		through the "dfu_bufsiz" environment variable.

1477 1478 1479 1480 1481 1482 1483
		CONFIG_SYS_DFU_MAX_FILE_SIZE
		When updating files rather than the raw storage device,
		we use a static buffer to copy the file into and then write
		the buffer once we've been given the whole file.  Define
		this to the maximum filesize (in bytes) for the buffer.
		Default is 4 MiB if undefined.

1484 1485 1486 1487 1488 1489 1490 1491 1492 1493
		DFU_DEFAULT_POLL_TIMEOUT
		Poll timeout [ms], is the timeout a device can send to the
		host. The host must wait for this timeout before sending
		a subsequent DFU_GET_STATUS request to the device.

		DFU_MANIFEST_POLL_TIMEOUT
		Poll timeout [ms], which the device sends to the host when
		entering dfuMANIFEST state. Host waits this timeout, before
		sending again an USB request to the device.

1494
- USB Device Android Fastboot support:
1495 1496 1497
		CONFIG_USB_FUNCTION_FASTBOOT
		This enables the USB part of the fastboot gadget

1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508
		CONFIG_CMD_FASTBOOT
		This enables the command "fastboot" which enables the Android
		fastboot mode for the platform's USB device. Fastboot is a USB
		protocol for downloading images, flashing and device control
		used on Android devices.
		See doc/README.android-fastboot for more information.

		CONFIG_ANDROID_BOOT_IMAGE
		This enables support for booting images which use the Android
		image format header.

1509
		CONFIG_FASTBOOT_BUF_ADDR
1510 1511 1512 1513
		The fastboot protocol requires a large memory buffer for
		downloads. Define this to the starting RAM address to use for
		downloaded images.

1514
		CONFIG_FASTBOOT_BUF_SIZE
1515 1516 1517
		The fastboot protocol requires a large memory buffer for
		downloads. This buffer should be as large as possible for a
		platform. Define this to the size available RAM for fastboot.
1518 1519 1520 1521 1522 1523 1524 1525 1526 1527

		CONFIG_FASTBOOT_FLASH
		The fastboot protocol includes a "flash" command for writing
		the downloaded image to a non-volatile storage device. Define
		this to enable the "fastboot flash" command.

		CONFIG_FASTBOOT_FLASH_MMC_DEV
		The fastboot "flash" command requires additional information
		regarding the non-volatile storage device. Define this to
		the eMMC device that fastboot should use to store the image.
1528

1529 1530 1531 1532 1533 1534 1535
		CONFIG_FASTBOOT_GPT_NAME
		The fastboot "flash" command supports writing the downloaded
		image to the Protective MBR and the Primary GUID Partition
		Table. (Additionally, this downloaded image is post-processed
		to generate and write the Backup GUID Partition Table.)
		This occurs when the specified "partition name" on the
		"fastboot flash" command line matches this value.
1536
		The default is "gpt" if undefined.
1537

1538 1539 1540 1541 1542 1543 1544
		CONFIG_FASTBOOT_MBR_NAME
		The fastboot "flash" command supports writing the downloaded
		image to DOS MBR.
		This occurs when the "partition name" specified on the
		"fastboot flash" command line matches this value.
		If not defined the default value "mbr" is used.

1545
- Journaling Flash filesystem support:
1546
		CONFIG_JFFS2_NAND
1547 1548
		Define these for a default partition on a NAND device

1549 1550
		CONFIG_SYS_JFFS2_FIRST_SECTOR,
		CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1551 1552
		Define these for a default partition on a NOR device

1553 1554
- FAT(File Allocation Table) filesystem write function support:
		CONFIG_FAT_WRITE
1555 1556 1557 1558 1559 1560

		Define this to enable support for saving memory data as a
		file in FAT formatted partition.

		This will also enable the command "fatwrite" enabling the
		user to write files to FAT.
1561

1562
- CBFS (Coreboot Filesystem) support:
1563 1564 1565 1566 1567 1568
		CONFIG_CMD_CBFS

		Define this to enable support for reading from a Coreboot
		filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
		and cbfsload.

1569 1570 1571 1572 1573 1574
- FAT(File Allocation Table) filesystem cluster size:
		CONFIG_FS_FAT_MAX_CLUSTSIZE

		Define the max cluster size for fat operations else
		a default value of 65536 will be defined.

wdenk's avatar
wdenk committed
1575
- Keyboard Support:
1576 1577 1578 1579 1580 1581 1582 1583 1584
		See Kconfig help for available keyboard drivers.

		CONFIG_KEYBOARD

		Define this to enable a custom keyboard support.
		This simply calls drv_keyboard_init() which must be
		defined in your board-specific files. This option is deprecated
		and is only used by novena. For new boards, use driver model
		instead.
wdenk's avatar
wdenk committed
1585 1586

- Video support:
1587
		CONFIG_FSL_DIU_FB
1588
		Enable the Freescale DIU video driver.	Reference boards for
1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600
		SOCs that have a DIU should define this macro to enable DIU
		support, and should also define these other macros:

			CONFIG_SYS_DIU_ADDR
			CONFIG_VIDEO
			CONFIG_CMD_BMP
			CONFIG_CFB_CONSOLE
			CONFIG_VIDEO_SW_CURSOR
			CONFIG_VGA_AS_SINGLE_DEVICE
			CONFIG_VIDEO_LOGO
			CONFIG_VIDEO_BMP_LOGO

1601 1602
		The DIU driver will look for the 'video-mode' environment
		variable, and if defined, enable the DIU as a console during
1603
		boot.  See the documentation file doc/README.video for a
1604
		description of this variable.
1605

wdenk's avatar
wdenk committed
1606 1607 1608 1609 1610 1611
- LCD Support:	CONFIG_LCD

		Define this to enable LCD support (for output to LCD
		display); also select one of the supported displays
		by defining one of these:

Stelian Pop's avatar
Stelian Pop committed
1612 1613 1614 1615
		CONFIG_ATMEL_LCD:

			HITACHI TX09D70VM1CCA, 3.5", 240x320.

wdenk's avatar
wdenk committed
1616
		CONFIG_NEC_NL6448AC33:
wdenk's avatar
wdenk committed
1617

wdenk's avatar
wdenk committed
1618
			NEC NL6448AC33-18. Active, color, single scan.
wdenk's avatar
wdenk committed
1619

wdenk's avatar
wdenk committed
1620
		CONFIG_NEC_NL6448BC20
wdenk's avatar
wdenk committed
1621

wdenk's avatar
wdenk committed
1622 1623 1624 1625 1626 1627
			NEC NL6448BC20-08. 6.5", 640x480.
			Active, color, single scan.

		CONFIG_NEC_NL6448BC33_54

			NEC NL6448BC33-54. 10.4", 640x480.
wdenk's avatar
wdenk committed
1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655
			Active, color, single scan.

		CONFIG_SHARP_16x9

			Sharp 320x240. Active, color, single scan.
			It isn't 16x9, and I am not sure what it is.

		CONFIG_SHARP_LQ64D341

			Sharp LQ64D341 display, 640x480.
			Active, color, single scan.

		CONFIG_HLD1045

			HLD1045 display, 640x480.
			Active, color, single scan.

		CONFIG_OPTREX_BW

			Optrex	 CBL50840-2 NF-FW 99 22 M5
			or
			Hitachi	 LMG6912RPFC-00T
			or
			Hitachi	 SP14Q002

			320x240. Black & white.

		Normally display is black on white background; define
1656
		CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
wdenk's avatar
wdenk committed
1657

1658 1659
		CONFIG_LCD_ALIGNMENT

1660
		Normally the LCD is page-aligned (typically 4KB). If this is
1661 1662 1663 1664 1665 1666
		defined then the LCD will be aligned to this value instead.
		For ARM it is sometimes useful to use MMU_SECTION_SIZE
		here, since it is cheaper to change data cache settings on
		a per-section basis.


1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686
		CONFIG_LCD_ROTATION

		Sometimes, for example if the display is mounted in portrait
		mode or even if it's mounted landscape but rotated by 180degree,
		we need to rotate our content of the display relative to the
		framebuffer, so that user can read the messages which are
		printed out.
		Once CONFIG_LCD_ROTATION is defined, the lcd_console will be
		initialized with a given rotation from "vl_rot" out of
		"vidinfo_t" which is provided by the board specific code.
		The value for vl_rot is coded as following (matching to
		fbcon=rotate:<n> linux-kernel commandline):
		0 = no rotation respectively 0 degree
		1 = 90 degree rotation
		2 = 180 degree rotation
		3 = 270 degree rotation

		If CONFIG_LCD_ROTATION is not defined, the console will be
		initialized with 0degree rotation.

1687 1688 1689 1690
		CONFIG_LCD_BMP_RLE8

		Support drawing of RLE8-compressed bitmaps on the LCD.

1691 1692 1693 1694 1695
		CONFIG_I2C_EDID

		Enables an 'i2c edid' command which can read EDID
		information over I2C from an attached LCD display.

wdenk's avatar
wdenk committed
1696
- Splash Screen Support: CONFIG_SPLASH_SCREEN
1697

wdenk's avatar
wdenk committed
1698 1699 1700
		If this option is set, the environment is checked for
		a variable "splashimage". If found, the usual display
		of logo, copyright and system information on the LCD
1701
		is suppressed and the BMP image at the address
wdenk's avatar
wdenk committed
1702 1703 1704 1705
		specified in "splashimage" is loaded instead. The
		console is redirected to the "nulldev", too. This
		allows for a "silent" boot where a splash screen is
		loaded very quickly after power-on.
1706

1707 1708 1709 1710
		CONFIG_SPLASHIMAGE_GUARD

		If this option is set, then U-Boot will prevent the environment
		variable "splashimage" from being set to a problematic address
1711
		(see doc/README.displaying-bmps).
1712 1713 1714 1715 1716 1717
		This option is useful for targets where, due to alignment
		restrictions, an improperly aligned BMP image will cause a data
		abort. If you think you will not have problems with unaligned
		accesses (for example because your toolchain prevents them)
		there is no need to set this option.

1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737
		CONFIG_SPLASH_SCREEN_ALIGN

		If this option is set the splash image can be freely positioned
		on the screen. Environment variable "splashpos" specifies the
		position as "x,y". If a positive number is given it is used as
		number of pixel from left/top. If a negative number is given it
		is used as number of pixel from right/bottom. You can also
		specify 'm' for centering the image.

		Example:
		setenv splashpos m,m
			=> image at center of screen

		setenv splashpos 30,20
			=> image at x = 30 and y = 20

		setenv splashpos -10,m
			=> vertically centered image
			   at x = dspWidth - bmpWidth - 9

1738 1739 1740 1741 1742 1743
- Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP

		If this option is set, additionally to standard BMP
		images, gzipped BMP images can be displayed via the
		splashscreen support or the bmp command.

1744 1745 1746 1747 1748 1749
- Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8

		If this option is set, 8-bit RLE compressed BMP images
		can be displayed via the splashscreen support or the
		bmp command.

1750
- Compression support:
1751 1752 1753 1754
		CONFIG_GZIP

		Enabled by default to support gzip compressed images.

1755 1756 1757 1758 1759 1760
		CONFIG_BZIP2

		If this option is set, support for bzip2 compressed
		images is included. If not, only uncompressed and gzip
		compressed images are supported.

1761
		NOTE: the bzip2 algorithm requires a lot of RAM, so
1762
		the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1763
		be at least 4MB.
1764

1765 1766 1767