- 06 Mar, 2021 3 commits
-
-
Angus Ainslie authored
The STL files now inlude the pinch Signed-off-by:Angus Ainslie <angus@akkea.ca>
-
Angus Ainslie authored
Make the default a slim case with a pinch. Signed-off-by: -
Angus Ainslie authored
Use better outside dimesnsions. Define a pinch paramter to make the top of the case thinner that the bottom so the case grips the phone better. Signed-off-by:
-
- 08 Jan, 2021 3 commits
-
-
Angus Ainslie authored
Signed-off-by: -
Angus Ainslie authored
The walls were tearing at 1.2 so make them a bit thicker. Signed-off-by: -
Angus Ainslie authored
This make the top of the case slightly smaller than the bottom so it fits more snugly. Signed-off-by:
-
- 07 Jan, 2021 6 commits
-
-
Angus Ainslie authored
Signed-off-by: -
Angus Ainslie authored
It ended up being too narrow still Signed-off-by: -
Angus Ainslie authored
Don't make the base smaller for a tigher fit. It doen't work. Signed-off-by: -
Angus Ainslie authored
Signed-off-by: -
Angus Ainslie authored
On the slim case the USB C was not all the way through Signed-off-by: -
Angus Ainslie authored
update the outline measurements Signed-off-by:
-
- 06 Jan, 2021 6 commits
-
-
Angus Ainslie authored
Signed-off-by: -
Angus Ainslie authored
Define an evergreen/dogwood switch. Define a slim case. define a case with no cutouts for raingear. Signed-off-by: -
Angus Ainslie authored
Define evergreen to set the case length. Define slim to create a tighter fitting case Signed-off-by: -
Angus Ainslie authored
Add intermediate outputs so that users don't need to install openscad to print this. Signed-off-by: -
Angus Ainslie authored
Decrease the bezel angles for ease of printing and to imporve the phone fitment Signed-off-by: -
Angus Ainslie authored
Center the flash within it's opening Signed-off-by:
-
- 03 Jan, 2021 2 commits
-
-
Angus Ainslie authored
The parameters in PhoneOutline.scad can be adjusted for dogwood or evergreen. Signed-off-by: -
Angus Ainslie authored
This was a devkit prototype case. It's not needed any more. Signed-off-by:
-
- 23 Nov, 2020 1 commit
-
-
David Hamner authored
-
- 29 Oct, 2020 1 commit
-
-
David Hamner authored
-
- 28 Oct, 2020 2 commits
-
-
David Hamner authored
-
David Hamner authored
-
- 27 Oct, 2020 2 commits
-
-
David Hamner authored
-
David Hamner authored
-
- 27 Dec, 2019 2 commits
-
-
Angus Ainslie authoredBattery: add an opescad representation of the phone battery See merge request !1
-
Angus Ainslie authored
This can be used to power the phone from a lab supply. Signed-off-by:
-
- 27 Mar, 2019 1 commit
-
-
Angus Ainslie authored
Move the button holes so they are in the correct places. Add a hole for the fan. Add a hole for the debug cable. Signed-off-by:
-
- 11 Feb, 2019 1 commit
-
-
Angus Ainslie authored
The original design was by MrPickle https://www.youmagine.com/designs/librem5-devkit-case Openscad adaptation by Angus Ainslie <angus.ainslie@puri.sm>
-
- 25 Feb, 2018 1 commit
-
-
Angus Ainslie authored
Nitrogen board.
-
- 09 Feb, 2018 1 commit
-
-
Angus Ainslie authored
-
- 31 Jan, 2018 2 commits
-
-
Nicole Faerber authored
-
Angus Ainslie authored
* move the connecter hole in board * thinken the base for added rigidity
-
- 30 Jan, 2018 2 commits
-
-
Nicole Faerber authored
-
Nicole Faerber authored
-
- 26 Jan, 2018 1 commit
-
-
Angus Ainslie authored
-