Skip to content

Changes

Page history
Update root partition resizing instructions so that they are done on the Librem 5 itself authored by gondolyr's avatar gondolyr
Show whitespace changes
Inline Side-by-side
Tips-&-Tricks.md
View page @ 11df7744
...@@ -61,104 +61,61 @@ GPS: Seems to work internally but user interfaces in PureOS are still missing (e ...@@ -61,104 +61,61 @@ GPS: Seems to work internally but user interfaces in PureOS are still missing (e
Related Mobian issue and workaround: <https://gitlab.com/mobian1/issues/-/issues/440#note_1018769896> Related Mobian issue and workaround: <https://gitlab.com/mobian1/issues/-/issues/440#note_1018769896>
[Reflashing the Librem 5](https://developer.puri.sm/Librem5/Development_Environment/Phone/Troubleshooting/Reflashing_the_Phone.html) may end up creating a root partition that does not use up the entire eMMC storage, usually with only 4GB with the rest being unallocated free space when this happens. You can use the "Disks" app on the Librem 5 to check; select the "31 GB Disk" option when the app opens and it is usually listed as "Partition 2". [Reflashing the Librem 5](https://developer.puri.sm/Librem5/Development_Environment/Phone/Troubleshooting/Reflashing_the_Phone.html) may end up creating a root partition that does not use up the entire eMMC storage, usually with only 4GB with the rest being unallocated free space when this happens.
You can use the "Disks" app on the Librem 5 to check; select the "31 GB Disk" option when the app opens and it is usually listed as "Partition 2"; alternatively, you can use `df -h` to see and look for the line that says `/` in the "Mounted on" column.
This limited storage space can cause errors when attempting to install additional apps from the PureOS Store because there would not be enough space to install the apps or any system updates. This limited storage space can cause errors when attempting to install additional apps from the PureOS Store because there would not be enough space to install the apps or any system updates.
If the root partition isn't using all of the eMMC storage, these steps will resize the partition to use the remaining free space. If the root partition isn't using all of the eMMC storage, these steps will resize the partition to use the entire eMMC capacity.
**Warning**: Before starting to resize a volume or its partition, a backup should be created. Follow these steps at your own risk! **Warning**: Before starting to resize a volume or its partition, a backup should be created. Follow these steps at your own risk!
1. Enter [flash mode](https://source.puri.sm/Librem5/community-wiki/-/wikis/Tips-&-Tricks#flash-mode) on the Librem 5. 1. From the Librem 5, open up the Terminal app.
2. Use [Jumpdrive](https://github.com/dreemurrs-embedded/Jumpdrive) to mount the Librem 5 as a USB disk. You may be prompted to unlock the LUKS partition. Ignore the prompt and leave it unmounted. You won't be able to resize the partition if it is being used.
3. On the host machine, open up a terminal and check to see which device is the Librem 5 using `lsblk`. In this example, `/dev/sdd` is the Librem 5; keep this path in mind for the following steps (If the Librem 5 is mounted at `/dev/sdb` or any other letter, `sdX`, use that instead). The LUKS volume, which is `/dev/sdd2` here, should not be unlocked yet. If it is, run `sudo cryptsetup close /dev/sdd2 <mount_name>` where `<mount_name>` is the name that the LUKS partition is mounted to.
```
$ lsblk
...
sdd 8:48 1 29.1G 0 disk
├─sdd1 8:49 1 465M 0 part /media/myuser/099d2c54-15c3-4354-963f-8d8d5c6a93a5
└─sdd2 8:50 1 3.7G 0 part
```
4. Use `parted` to resize the LUKS partition. You can install `parted` with `sudo apt install parted` if you don't have it. 2. Check to see the total size of the root partition by entering `df -h`. If the partition is only about 4 GB, then you have this issue.
``` ```sh
$ sudo parted /dev/sdd $ df -h
GNU Parted 3.4 Filesystem Size Used Avail Use% Mounted on
Using /dev/sdd /dev/dm-0 3.6G 3.4G 54M 99% /
overlay 3.6G 3.4G 54M 99% /usr/lb/firmware
``` ```
1. Inside `parted` run `print` just to make sure you are using the proper device. You should see two primary partitions: 3. Use GNU Parted to resize the root partition. The following command will enter an interactive prompt.
``` ```sh
(parted) print $ sudo parted /dev/mmcblk0
Model: JumpDrive eMMC (scsi)
Disk /dev/sdd: 31.3GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
1 5243kB 493MB 488MB primary ext2 boot
2 493MB 4499MB 4007MB primary
``` ```
2. Enlarge the 2nd to 100% capacity. 4. Enter the following lines while in the GNU Parted prompt to resize the partition.
```sh
resizepart 2 30.5GB
quit
``` ```
(parted) resizepart 2 100%
```
3. Print to see if the partition expanded correctly and then quit the program.
``` This will look like the following in the terminal app:
(parted) print
Model: JumpDrive eMMC (scsi)
Disk Flags:
Number Start End Size Type File system Flags ```sh
1 5243kB 493MB 488MB primary ext2 boot (parted) resizepart 2 30.5GB
2 493MB 31.3GB 30.8GB primary
(parted) quit (parted) quit
Information: You may need to update /etc/fstab.
```
5. If you’re using an encrypted device run the following command – you will be asked for your encryption password. The encrypted LUKS volume is not automatically resized from the previous steps. To resize the LUKS encrypted volume, the encrypted volume needs to be opened. To open the volume, the "open" command is used. The "librem5_crypt" volume name is arbitrary and you can name it anything else such as "l5lv" if you wish. The LUKS password is "123456" by default.
```
$ sudo cryptsetup open /dev/sdd2 librem5_crypt
Enter passphrase for /dev/sdd2: <PASSWORD>
``` ```
6. The resize command takes the volume name as specified while opening the volume in the previous step. The command will not show any output without the `-v` option. 5. If the disk is encrypted, run the 3 following commands:
```sh
sudo cryptsetup resize /dev/mapper/crypt_root
sudo resize2fs /dev/mapper/crypt_root
``` ```
$ sudo cryptsetup resize librem5_crypt -v
No usable token is available.
Enter passphrase for /dev/sdd2:
Key slot 0 unlocked.
Command successful.
```
7. Finally, the file system needs to be expanded to the new size. The `e2fsck` tool must be run before `resize2fs` or else `resize2fs` will return an error `Please run 'e2fsck -f /dev/mapper/librem5_crypt' first.`.
``` 6. Reboot the device.
$ sudo e2fsck -f /dev/mapper/librem5_crypt
e2fsck 1.46.5 (30-Dec-2021)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/mapper/librem5_crypt: 97714/243840 files (0.2% non-contiguous), 749235/974080 blocks
```
``` ```sh
$ sudo resize2fs -p /dev/mapper/librem5_crypt sudo reboot
resize2fs 1.46.5 (30-Dec-2021)
Resizing the filesystem on /dev/mapper/librem5_crypt to 7509504 (4k) blocks.
The filesystem on /dev/mapper/librem5_crypt is now 7509504 (4k) blocks long.
``` ```
8. The Librem 5 should be safely removed from the host computer before booting up the Librem 5 and you should now see the root partition use up all of the available eMMC space. 7. After the Librem 5 has rebooted, open up the Terminal app and check the partition size again with `df -h` to confirm that the root partition has a capacity of around 31 GB.
## General ## General
......