1. 17 Oct, 2018 2 commits
  2. 26 Sep, 2018 1 commit
  3. 22 Sep, 2018 1 commit
  4. 14 Sep, 2018 1 commit
  5. 05 Sep, 2018 1 commit
  6. 24 Aug, 2018 1 commit
  7. 21 Aug, 2018 2 commits
  8. 20 Aug, 2018 3 commits
  9. 19 Aug, 2018 4 commits
  10. 17 Aug, 2018 1 commit
    • Eric Kuzmenko's avatar
      Update the fabrication drawing file with more information · 7d4a9d76
      Eric Kuzmenko authored
      This file was created by exporting both the Cmts.User layer, as well as the NPTH&PTH drills into separate DXF files, then combining them in the footprint editor, finally, this new footprint made from both of these is imported into the layout and re-exported as a single DXF.
      7d4a9d76
  11. 16 Aug, 2018 1 commit
    • Eric Kuzmenko's avatar
      Make the backlight boost converter compensation capacitor (C459) 10nF instead... · 9234b540
      Eric Kuzmenko authored
      Make the backlight boost converter compensation capacitor (C459) 10nF instead of 100nF (was a typo), make the charge controller's PMID capacitor (C302) 10uF instead of 8.2uF since it is a more common value and is what is being used on the charge controller's eval board, select a 10uF 0603 X5R capacitor rated for 25V for both the PMID cap and the 10uF cap on VBUS, update the .ods BoM with tolerances & ratings for the caps and resistors which will be supplied by the PCBA house, export the component-placement-list file (dvk-mx8m-bsb-all.pos) which gives the coordinates of all components with respect to the top-left fiducial mark, re-export the gerbers for preliminary review (add silkscreen which states that this is preliminary instead of a version number), make a few minor improvements to the board's routing in various spots, update the IMU footprint so that its silkscreen which gives the axis directions is visible on the board, some footprints were updated to be defined as SMD footprints in order to show up on the component-placement list (strictly through-hole components are not listed)
      
      The 0603 10uF 25V caps have been ordered and will be shipped to wherever the assembly is done. This commit contains the preliminary materials which will be reviewed (BoM, .pos file, and gerbers all zipped).
      9234b540
  12. 15 Aug, 2018 3 commits
  13. 14 Aug, 2018 2 commits
    • Eric Kuzmenko's avatar
      Add a 5.29x27.14mm Purism logo to the "back" silkscreen of the board, seen on... · 0154972b
      Eric Kuzmenko authored
      Add a 5.29x27.14mm Purism logo to the "back" silkscreen of the board, seen on the bottom left edge when facing the display, remove the old schematic rescue files which are remnants from the Kicad 5.0.0 upgrade
      0154972b
    • Eric Kuzmenko's avatar
      Move the two tantalum capacitors which were on the "back" to the "front" side,... · c4d560e2
      Eric Kuzmenko authored
      Move the two tantalum capacitors which were on the "back" to the "front" side, make corrections to the battery holder footprint including a hole which was missing for plastic pillar dealy (3D model contradicts the recommended footprint, may need to be adjusted depending on prototypes), place the 3V3_P and 1V8_P bypass caps throughout the board (as well as two of the 5V_P caps)
      
      Only 8 more 5V_P bypass caps need to be placed and the unrouted count will be 0!
      c4d560e2
  14. 10 Aug, 2018 1 commit
  15. 08 Aug, 2018 4 commits
  16. 07 Aug, 2018 3 commits
  17. 06 Aug, 2018 1 commit
  18. 04 Aug, 2018 1 commit
  19. 03 Aug, 2018 4 commits
  20. 02 Aug, 2018 2 commits
  21. 01 Aug, 2018 1 commit