1. 17 Oct, 2018 1 commit
  2. 20 Sep, 2018 1 commit
  3. 16 Aug, 2018 1 commit
  4. 14 Aug, 2018 1 commit
  5. 11 Aug, 2018 1 commit
  6. 26 Jul, 2018 2 commits
  7. 25 Jul, 2018 1 commit
  8. 20 Jul, 2018 1 commit
  9. 09 Jul, 2018 1 commit
  10. 05 Jul, 2018 1 commit
  11. 04 Jul, 2018 1 commit
    • Eric Kuzmenko's avatar
      Now using GPIO5_IO03 (P4.03) to put the class-D op-amp in shutdown and... · 3bf0094e
      Eric Kuzmenko authored
      Now using GPIO5_IO03 (P4.03) to put the class-D op-amp in shutdown and conserve energy when muted, make C1716 near the ETH PHY's DVDDL pin 47 220nF instead of 10uF (EmCraft suggested that this should be 100nF but their's is 220nF, asked why), added a 10k pull-down to PAM2841's ENA pin, added a 100nF cap to the smart card's C1 VCC pin, added a 1uF cap to the haptic motor circuit's 3V3_P rail
      
      Still need to use I2C3 instead of I2C1 according to EmCraft's suggestions.
      3bf0094e
  12. 03 Jul, 2018 2 commits
  13. 02 Jul, 2018 1 commit
  14. 26 Jun, 2018 2 commits
  15. 25 Jun, 2018 2 commits
  16. 22 Jun, 2018 3 commits
    • Christian Schilmoeller's avatar
      added library symbol for short internal coaxial cables (from u.FL connector of... · b270ca43
      Christian Schilmoeller authored
      added library symbol for short internal coaxial cables (from u.FL connector of M.2/MiniPCIE Card to ceramic antenna).
      This component is not appearing at the pcb. The library symbols serves only as a memory aid.
      Supplier information can be linked to it and should appear then on the BoM.
      b270ca43
    • Christian Schilmoeller's avatar
      Small change in footprint assignment of the SOM: · 12e88a43
      Christian Schilmoeller authored
      Old situation:
      First footprint of the SOM contains outline, mounting holes, footprint of P1 and markers for positions of P2, P3 and P4.
      Second, third and forth footprint contain only P2..P4 connectors.
      This situation leads to a problem with the BoM, because the 4 identical connectors could not be grouped together.
      
      New situation:
      Outline, mounting holes and position markers are now located in the footprint which is assigned to the SOM placeholder
      4 identical footprints assigned to the SOM's connectors P1..P4 contain only the connector footprint.
      This shouldn't cause problems with the BoM.
      12e88a43
    • Eric Kuzmenko's avatar
      Add mounting holes to the schematic and assign the associated M2 hole... · 7d21696e
      Eric Kuzmenko authored
      Add mounting holes to the schematic and assign the associated M2 hole footprint, add fiducial marks to schematic and assign the associated 1mm diameter copper with 2mm diameter solder mask opening footprint, make various visual adjustments throughout the schematic
      7d21696e
  17. 21 Jun, 2018 3 commits
  18. 20 Jun, 2018 1 commit
  19. 19 Jun, 2018 4 commits
  20. 16 Jun, 2018 1 commit
  21. 15 Jun, 2018 3 commits
  22. 14 Jun, 2018 1 commit
  23. 13 Jun, 2018 4 commits
  24. 11 Jun, 2018 1 commit