1. 21 May, 2019 1 commit
  2. 01 Nov, 2018 1 commit
  3. 14 Aug, 2018 1 commit
    • Eric Kuzmenko's avatar
      Make the ENET_* traces on the top layer 53mils in order to ensure they have a... · 2456bfb3
      Eric Kuzmenko authored
      Make the ENET_* traces on the top layer 53mils in order to ensure they have a 50Ohm single-ended impedence, move one of the 5V_P bypass caps close to the SoM end of the USB2 diff pair, add meanders to the ENET_TXC, ENET_TX_CTL, ENET_RX_CTL in order to ensure these segments are matched to the long ENET_RXC segment (56.051mm, the rest of the RGMII signals are <10mm skew from this length and don't need adjusting, re-route the SIM card such that UIM-RESET is routed in between UIM-CLK and UIM-DATA as recommended by a BB manufacturer
      2456bfb3
  4. 03 Aug, 2018 1 commit
    • Eric Kuzmenko's avatar
      Add pi-matching circuit to the baseband modem antenna's feedline · 2f8fb756
      Eric Kuzmenko authored
      The return path for the antenna may have to have a 6.8nH Murata LQG15HN inductor installed on it (cutting the ground trace shorting the pads). The BoM was updated with the new components and everything was reannotated and updated (page 2's caps were out of order).
      2f8fb756
  5. 23 Jul, 2018 2 commits
  6. 17 Jul, 2018 1 commit
  7. 16 Jul, 2018 1 commit
  8. 09 Jul, 2018 2 commits
  9. 05 Jul, 2018 1 commit
  10. 04 Jul, 2018 1 commit
    • Eric Kuzmenko's avatar
      Now using GPIO5_IO03 (P4.03) to put the class-D op-amp in shutdown and... · 3bf0094e
      Eric Kuzmenko authored
      Now using GPIO5_IO03 (P4.03) to put the class-D op-amp in shutdown and conserve energy when muted, make C1716 near the ETH PHY's DVDDL pin 47 220nF instead of 10uF (EmCraft suggested that this should be 100nF but their's is 220nF, asked why), added a 10k pull-down to PAM2841's ENA pin, added a 100nF cap to the smart card's C1 VCC pin, added a 1uF cap to the haptic motor circuit's 3V3_P rail
      
      Still need to use I2C3 instead of I2C1 according to EmCraft's suggestions.
      3bf0094e
  11. 26 Jun, 2018 1 commit
  12. 24 Jun, 2018 1 commit
    • Eric Kuzmenko's avatar
      Add proper WWAN reset circuit using a MMBT2222A NPN BJT along with a 100nF cap... · 3b5880ca
      Eric Kuzmenko authored
      Add proper WWAN reset circuit using a MMBT2222A NPN BJT along with a 100nF cap and a TVS diode, make needed adjustements to the WWAN's SIM card circuit (UIM-CLK and UIM-RESET caps are NC & added 4.7k series resistor to SIM_DETECT_O#), assign the MMBT2222A footprint to KiCad's official SOT-23 footprint (identical to the spec sheet's recommended land pattern)
      
      If necessary, the NC cap pads on UIM-CLK and UIM-RESET can be tested with various values during the first prototype debugging phase.
      3b5880ca
  13. 23 Jun, 2018 1 commit
  14. 22 Jun, 2018 1 commit
  15. 20 Jun, 2018 2 commits
  16. 19 Jun, 2018 2 commits
  17. 17 Jun, 2018 2 commits
  18. 15 Jun, 2018 3 commits
  19. 13 Jun, 2018 3 commits
  20. 12 Jun, 2018 1 commit
    • Eric Kuzmenko's avatar
      Add GNSS antenna footprint including correct 50Ohm feed line dimensions and... · 05b25768
      Eric Kuzmenko authored
      Add GNSS antenna footprint including correct 50Ohm feed line dimensions and keepout area, add u-blox MAX-8 3D model, rename all instances of MAX-M8* to MAX-8* due to part selection, antenna feed line calculatos included (coplanar waveguide)
      
      Need to add placeholder footprints for the other four antennae which will be represented as simple rectangular areas where the antennae will occupy. After that, all that is left is to assign the various remaining IC footprints and finally import all footprints into PCBNew & begin layout!
      05b25768
  21. 11 Jun, 2018 2 commits
  22. 07 Jun, 2018 2 commits
  23. 06 Jun, 2018 2 commits
  24. 04 Jun, 2018 1 commit
    • Eric Kuzmenko's avatar
      Replace the AP22800 load switch with the P-channel AP22814 load switch IC due... · e1a47582
      Eric Kuzmenko authored
      Replace the AP22800 load switch with the P-channel AP22814 load switch IC due to its reverse current & over current protection capability, add level shifter circuit to the WWAN's DPR signal
      
      Reverse current is no longer an issue with the load switches. One more obvious "TODO" for the schematic left which is to simply place several 100nF bypass caps on the 5V_P, 3V3_P, and 1V8_P rails (investigate how EmCraft is placing these in their layout).
      e1a47582
  25. 02 Jun, 2018 2 commits
  26. 01 Jun, 2018 2 commits