jmicron.c 4.47 KB
Newer Older
1 2

/*
3
 * Copyright (C) 2006		Red Hat
4 5 6 7 8 9 10 11 12 13
 *
 *  May be copied or modified under the terms of the GNU General Public License
 */

#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>

14 15
#define DRV_NAME "jmicron"

16 17 18 19 20 21 22
typedef enum {
	PORT_PATA0 = 0,
	PORT_PATA1 = 1,
	PORT_SATA = 2,
} port_type;

/**
23
 *	jmicron_cable_detect	-	cable detection
24 25
 *	@hwif: IDE port
 *
26
 *	Returns the cable type.
27 28
 */

29
static u8 jmicron_cable_detect(ide_hwif_t *hwif)
30
{
31
	struct pci_dev *pdev = to_pci_dev(hwif->dev);
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

	u32 control;
	u32 control5;

	int port = hwif->channel;
	port_type port_map[2];

	pci_read_config_dword(pdev, 0x40, &control);

	/* There are two basic mappings. One has the two SATA ports merged
	   as master/slave and the secondary as PATA, the other has only the
	   SATA port mapped */
	if (control & (1 << 23)) {
		port_map[0] = PORT_SATA;
		port_map[1] = PORT_PATA0;
	} else {
		port_map[0] = PORT_SATA;
		port_map[1] = PORT_SATA;
	}

	/* The 365/366 may have this bit set to map the second PATA port
	   as the internal primary channel */
	pci_read_config_dword(pdev, 0x80, &control5);
	if (control5 & (1<<24))
		port_map[0] = PORT_PATA1;

	/* The two ports may then be logically swapped by the firmware */
	if (control & (1 << 22))
		port = port ^ 1;

	/*
	 *	Now we know which physical port we are talking about we can
	 *	actually do our cable checking etc. Thankfully we don't need
	 *	to do the plumbing for other cases.
	 */
67
	switch (port_map[port]) {
68 69
	case PORT_PATA0:
		if (control & (1 << 3))	/* 40/80 pin primary */
70 71
			return ATA_CBL_PATA40;
		return ATA_CBL_PATA80;
72 73
	case PORT_PATA1:
		if (control5 & (1 << 19))	/* 40/80 pin secondary */
74 75
			return ATA_CBL_PATA40;
		return ATA_CBL_PATA80;
76
	case PORT_SATA:
Andrew Morton's avatar
Andrew Morton committed
77
		break;
78
	}
79 80
	/* Avoid bogus "control reaches end of non-void function" */
	return ATA_CBL_PATA80;
81 82
}

83
static void jmicron_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
84 85 86 87
{
}

/**
88
 *	jmicron_set_dma_mode	-	set host controller for DMA mode
89
 *	@hwif: port
90
 *	@drive: drive
91
 *
92
 *	As the JMicron snoops for timings we don't need to do anything here.
93 94
 */

95
static void jmicron_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
96 97 98
{
}

99 100 101 102 103
static const struct ide_port_ops jmicron_port_ops = {
	.set_pio_mode		= jmicron_set_pio_mode,
	.set_dma_mode		= jmicron_set_dma_mode,
	.cable_detect		= jmicron_cable_detect,
};
104

105
static const struct ide_port_info jmicron_chipset = {
106
	.name		= DRV_NAME,
107
	.enablebits	= { { 0x40, 0x01, 0x01 }, { 0x40, 0x10, 0x10 } },
108
	.port_ops	= &jmicron_port_ops,
109
	.pio_mask	= ATA_PIO5,
110 111
	.mwdma_mask	= ATA_MWDMA2,
	.udma_mask	= ATA_UDMA6,
112 113 114 115 116 117 118 119 120 121 122
};

/**
 *	jmicron_init_one	-	pci layer discovery entry
 *	@dev: PCI device
 *	@id: ident table entry
 *
 *	Called by the PCI code when it finds a Jmicron controller.
 *	We then use the IDE PCI generic helper to do most of the work.
 */

123
static int jmicron_init_one(struct pci_dev *dev, const struct pci_device_id *id)
124
{
125
	return ide_pci_init_one(dev, &jmicron_chipset, NULL);
126 127
}

128 129 130 131 132 133 134 135
/* All JMB PATA controllers have and will continue to have the same
 * interface.  Matching vendor and device class is enough for all
 * current and future controllers if the controller is programmed
 * properly.
 *
 * If libata is configured, jmicron PCI quirk programs the controller
 * into the correct mode.  If libata isn't configured, match known
 * device IDs too to maintain backward compatibility.
136
 */
137
static struct pci_device_id jmicron_pci_tbl[] = {
138 139 140 141 142 143 144 145 146
#if !defined(CONFIG_ATA) && !defined(CONFIG_ATA_MODULE)
	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB361) },
	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB363) },
	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB365) },
	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB366) },
	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB368) },
#endif
	{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
	  PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 0 },
147 148 149 150 151
	{ 0, },
};

MODULE_DEVICE_TABLE(pci, jmicron_pci_tbl);

152
static struct pci_driver jmicron_pci_driver = {
153 154 155
	.name		= "JMicron IDE",
	.id_table	= jmicron_pci_tbl,
	.probe		= jmicron_init_one,
156
	.remove		= ide_pci_remove,
157 158
	.suspend	= ide_pci_suspend,
	.resume		= ide_pci_resume,
159 160 161 162
};

static int __init jmicron_ide_init(void)
{
163
	return ide_pci_register_driver(&jmicron_pci_driver);
164 165
}

166 167
static void __exit jmicron_ide_exit(void)
{
168
	pci_unregister_driver(&jmicron_pci_driver);
169 170
}

171
module_init(jmicron_ide_init);
172
module_exit(jmicron_ide_exit);
173 174 175 176

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("PCI driver module for the JMicron in legacy modes");
MODULE_LICENSE("GPL");