moxa-smartio 20.1 KB
Newer Older
Linus Torvalds's avatar
Linus Torvalds committed
1
=============================================================================
2 3 4
          MOXA Smartio/Industio Family Device Driver Installation Guide
		    for Linux Kernel 2.4.x, 2.6.x
	       Copyright (C) 2008, Moxa Inc.
Linus Torvalds's avatar
Linus Torvalds committed
5
=============================================================================
6 7
Date: 01/21/2008

Linus Torvalds's avatar
Linus Torvalds committed
8 9 10 11 12
Content

1. Introduction
2. System Requirement
3. Installation
13 14 15 16 17 18 19
   3.1 Hardware installation
   3.2 Driver files
   3.3 Device naming convention
   3.4 Module driver configuration
   3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x.
   3.6 Custom configuration
   3.7 Verify driver installation
Linus Torvalds's avatar
Linus Torvalds committed
20 21 22 23 24 25 26
4. Utilities
5. Setserial
6. Troubleshooting

-----------------------------------------------------------------------------
1. Introduction

27
   The Smartio/Industio/UPCI family Linux driver supports following multiport
Linus Torvalds's avatar
Linus Torvalds committed
28 29
   boards.

30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
    - 2 ports multiport board
	CP-102U, CP-102UL, CP-102UF
	CP-132U-I, CP-132UL,
	CP-132, CP-132I, CP132S, CP-132IS,
	CI-132, CI-132I, CI-132IS,
	(C102H, C102HI, C102HIS, C102P, CP-102, CP-102S)

    - 4 ports multiport board
	CP-104EL,
	CP-104UL, CP-104JU,
	CP-134U, CP-134U-I,
	C104H/PCI, C104HS/PCI,
	CP-114, CP-114I, CP-114S, CP-114IS, CP-114UL,
	C104H, C104HS,
	CI-104J, CI-104JS,
	CI-134, CI-134I, CI-134IS,
	(C114HI, CT-114I, C104P)
	POS-104UL,
	CB-114,
	CB-134I

    - 8 ports multiport board
	CP-118EL, CP-168EL,
	CP-118U, CP-168U,
	C168H/PCI,
	C168H, C168HS,
	(C168P),
	CB-108
Linus Torvalds's avatar
Linus Torvalds committed
58 59

   This driver and installation procedure have been developed upon Linux Kernel
60 61 62 63
   2.4.x and 2.6.x. This driver supports Intel x86 hardware platform. In order
   to maintain compatibility, this version has also been properly tested with
   RedHat, Mandrake, Fedora and S.u.S.E Linux. However, if compatibility problem
   occurs, please contact Moxa at support@moxa.com.tw.
Linus Torvalds's avatar
Linus Torvalds committed
64 65 66

   In addition to device driver, useful utilities are also provided in this
   version. They are
67 68
    - msdiag     Diagnostic program for displaying installed Moxa
                 Smartio/Industio boards.
Linus Torvalds's avatar
Linus Torvalds committed
69 70 71 72 73 74 75 76 77 78
    - msmon      Monitor program to observe data count and line status signals.
    - msterm     A simple terminal program which is useful in testing serial
	         ports.
    - io-irq.exe Configuration program to setup ISA boards. Please note that
                 this program can only be executed under DOS.

   All the drivers and utilities are published in form of source code under
   GNU General Public License in this version. Please refer to GNU General
   Public License announcement in each source code file for more detail.

79
   In Moxa's Web sites, you may always find latest driver at http://www.moxa.com/.
Linus Torvalds's avatar
Linus Torvalds committed
80 81 82 83 84 85 86 87 88 89 90 91

   This version of driver can be installed as Loadable Module (Module driver)
   or built-in into kernel (Static driver). You may refer to following
   installation procedure for suitable one. Before you install the driver,
   please refer to hardware installation procedure in the User's Manual.

   We assume the user should be familiar with following documents.
   - Serial-HOWTO
   - Kernel-HOWTO

-----------------------------------------------------------------------------
2. System Requirement
92 93
   - Hardware platform: Intel x86 machine
   - Kernel version: 2.4.x or 2.6.x
Linus Torvalds's avatar
Linus Torvalds committed
94 95 96 97 98 99
   - gcc version 2.72 or later
   - Maximum 4 boards can be installed in combination

-----------------------------------------------------------------------------
3. Installation

100 101 102 103 104 105 106 107 108
   3.1 Hardware installation
   3.2 Driver files
   3.3 Device naming convention
   3.4 Module driver configuration
   3.5 Static driver configuration for Linux kernel 2.4.x, 2.6.x.
   3.6 Custom configuration
   3.7 Verify driver installation


Linus Torvalds's avatar
Linus Torvalds committed
109 110
   3.1 Hardware installation

111 112
       There are two types of buses, ISA and PCI, for Smartio/Industio
       family multiport board.
Linus Torvalds's avatar
Linus Torvalds committed
113 114 115 116 117 118 119 120

       ISA board
       ---------
       You'll have to configure CAP address, I/O address, Interrupt Vector
       as well as IRQ before installing this driver. Please refer to hardware
       installation procedure in User's Manual before proceed any further.
       Please make sure the JP1 is open after the ISA board is set properly.

121 122
       PCI/UPCI board
       --------------
Linus Torvalds's avatar
Linus Torvalds committed
123 124 125 126
       You may need to adjust IRQ usage in BIOS to avoid from IRQ conflict
       with other ISA devices. Please refer to hardware installation
       procedure in User's Manual in advance.

127
       PCI IRQ Sharing
Linus Torvalds's avatar
Linus Torvalds committed
128 129
       -----------
       Each port within the same multiport board shares the same IRQ. Up to
130 131 132
       4 Moxa Smartio/Industio PCI Family multiport boards can be installed
       together on one system and they can share the same IRQ.

Linus Torvalds's avatar
Linus Torvalds committed
133

134
   3.2 Driver files
Linus Torvalds's avatar
Linus Torvalds committed
135 136 137 138 139

       The driver file may be obtained from ftp, CD-ROM or floppy disk. The
       first step, anyway, is to copy driver file "mxser.tgz" into specified
       directory. e.g. /moxa. The execute commands as below.

140 141
       # cd /
       # mkdir moxa
Linus Torvalds's avatar
Linus Torvalds committed
142
       # cd /moxa
143 144
       # tar xvf /dev/fd0

Linus Torvalds's avatar
Linus Torvalds committed
145
       or
146 147 148

       # cd /
       # mkdir moxa
Linus Torvalds's avatar
Linus Torvalds committed
149 150 151 152
       # cd /moxa
       # cp /mnt/cdrom/<driver directory>/mxser.tgz .
       # tar xvfz mxser.tgz

153 154 155

   3.3 Device naming convention

Linus Torvalds's avatar
Linus Torvalds committed
156 157
       You may find all the driver and utilities files in /moxa/mxser.
       Following installation procedure depends on the model you'd like to
158 159
       run the driver. If you prefer module driver, please refer to 3.4.
       If static driver is required, please refer to 3.5.
Linus Torvalds's avatar
Linus Torvalds committed
160 161 162

       Dialin and callout port
       -----------------------
163
       This driver remains traditional serial device properties. There are
Linus Torvalds's avatar
Linus Torvalds committed
164 165 166 167 168 169
       two special file name for each serial port. One is dial-in port
       which is named "ttyMxx". For callout port, the naming convention
       is "cumxx".

       Device naming when more than 2 boards installed
       -----------------------------------------------
170 171
       Naming convention for each Smartio/Industio multiport board is
       pre-defined as below.
Linus Torvalds's avatar
Linus Torvalds committed
172 173 174 175 176 177 178

       Board Num.	 Dial-in Port	      Callout port
       1st board	ttyM0  - ttyM7	      cum0  - cum7
       2nd board	ttyM8  - ttyM15       cum8  - cum15
       3rd board	ttyM16 - ttyM23       cum16 - cum23
       4th board	ttyM24 - ttym31       cum24 - cum31

179 180 181 182 183 184

       !!!!!!!!!!!!!!!!!!!! NOTE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
       Under Kernel 2.6 the cum Device is Obsolete. So use ttyM*
       device instead.
       !!!!!!!!!!!!!!!!!!!! NOTE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Linus Torvalds's avatar
Linus Torvalds committed
185 186 187 188 189 190 191 192 193
       Board sequence
       --------------
       This driver will activate ISA boards according to the parameter set
       in the driver. After all specified ISA board activated, PCI board
       will be installed in the system automatically driven.
       Therefore the board number is sorted by the CAP address of ISA boards.
       For PCI boards, their sequence will be after ISA boards and C168H/PCI
       has higher priority than C104H/PCI boards.

194
   3.4 Module driver configuration
Linus Torvalds's avatar
Linus Torvalds committed
195 196 197
       Module driver is easiest way to install. If you prefer static driver
       installation, please skip this paragraph.

198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243

       ------------- Prepare to use the MOXA driver--------------------
       3.4.1 Create tty device with correct major number
          Before using MOXA driver, your system must have the tty devices
          which are created with driver's major number. We offer one shell
          script "msmknod" to simplify the procedure.
          This step is only needed to be executed once. But you still
          need to do this procedure when:
          a. You change the driver's major number. Please refer the "3.7"
             section.
          b. Your total installed MOXA boards number is changed. Maybe you
             add/delete one MOXA board.
          c. You want to change the tty name. This needs to modify the
             shell script "msmknod"

          The procedure is:
	  # cd /moxa/mxser/driver
	  # ./msmknod

          This shell script will require the major number for dial-in
          device and callout device to create tty device. You also need
          to specify the total installed MOXA board number. Default major
          numbers for dial-in device and callout device are 30, 35. If
          you need to change to other number, please refer section "3.7"
          for more detailed procedure.
          Msmknod will delete any special files occupying the same device
          naming.

       3.4.2 Build the MOXA driver and utilities
          Before using the MOXA driver and utilities, you need compile the
          all the source code. This step is only need to be executed once.
          But you still re-compile the source code if you modify the source
          code. For example, if you change the driver's major number (see
          "3.7" section), then you need to do this step again.

          Find "Makefile" in /moxa/mxser, then run

	  # make clean; make install

          !!!!!!!!!! NOTE !!!!!!!!!!!!!!!!!
	  For Red Hat 9, Red Hat Enterprise Linux AS3/ES3/WS3 & Fedora Core1:
	  # make clean; make installsp1

	  For Red Hat Enterprise Linux AS4/ES4/WS4:
	  # make clean; make installsp2
          !!!!!!!!!! NOTE !!!!!!!!!!!!!!!!!
Linus Torvalds's avatar
Linus Torvalds committed
244 245

	  The driver files "mxser.o" and utilities will be properly compiled
246
	  and copied to system directories respectively.
Linus Torvalds's avatar
Linus Torvalds committed
247

248 249
       ------------- Load MOXA driver--------------------
       3.4.3 Load the MOXA driver
Linus Torvalds's avatar
Linus Torvalds committed
250

251
	  # modprobe mxser <argument>
Linus Torvalds's avatar
Linus Torvalds committed
252

253 254 255 256 257 258 259 260 261 262 263 264 265 266
	  will activate the module driver. You may run "lsmod" to check
	  if "mxser" is activated. If the MOXA board is ISA board, the
          <argument> is needed. Please refer to section "3.4.5" for more
          information.


       ------------- Load MOXA driver on boot --------------------
       3.4.4 For the above description, you may manually execute
          "modprobe mxser" to activate this driver and run
	  "rmmod mxser" to remove it.
          However, it's better to have a boot time configuration to
          eliminate manual operation. Boot time configuration can be
          achieved by rc file. We offer one "rc.mxser" file to simplify
          the procedure under "moxa/mxser/driver".
Linus Torvalds's avatar
Linus Torvalds committed
267

268 269 270 271 272 273
          But if you use ISA board, please modify the "modprobe ..." command
          to add the argument (see "3.4.5" section). After modifying the
          rc.mxser, please try to execute "/moxa/mxser/driver/rc.mxser"
          manually to make sure the modification is ok. If any error
          encountered, please try to modify again. If the modification is
          completed, follow the below step.
Linus Torvalds's avatar
Linus Torvalds committed
274

275
	  Run following command for setting rc files.
Linus Torvalds's avatar
Linus Torvalds committed
276 277 278 279 280

	  # cd /moxa/mxser/driver
	  # cp ./rc.mxser /etc/rc.d
	  # cd /etc/rc.d

281 282 283
	  Check "rc.serial" is existed or not. If "rc.serial" doesn't exist,
	  create it by vi, run "chmod 755 rc.serial" to change the permission.
	  Add "/etc/rc.d/rc.mxser" in last line,
Linus Torvalds's avatar
Linus Torvalds committed
284

285
          Reboot and check if moxa.o activated by "lsmod" command.
Linus Torvalds's avatar
Linus Torvalds committed
286

287 288 289 290
       3.4.5. If you'd like to drive Smartio/Industio ISA boards in the system,
          you'll have to add parameter to specify CAP address of given
	  board while activating "mxser.o". The format for parameters are
	  as follows.
Linus Torvalds's avatar
Linus Torvalds committed
291

292
	  modprobe mxser ioaddr=0x???,0x???,0x???,0x???
Linus Torvalds's avatar
Linus Torvalds committed
293 294 295 296 297 298
				|      |     |	  |
				|      |     |	  +- 4th ISA board
				|      |     +------ 3rd ISA board
				|      +------------ 2nd ISA board
				+------------------- 1st ISA board

299 300 301 302 303 304 305 306 307 308 309 310
   3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x

       Note: To use static driver, you must install the linux kernel
             source package.

       3.5.1 Backup the built-in driver in the kernel.
          # cd /usr/src/linux/drivers/char
          # mv mxser.c mxser.c.old

          For Red Hat 7.x user, you need to create link:
          # cd /usr/src
          # ln -s linux-2.4 linux
Linus Torvalds's avatar
Linus Torvalds committed
311

312
       3.5.2 Create link
Linus Torvalds's avatar
Linus Torvalds committed
313 314 315
	  # cd /usr/src/linux/drivers/char
	  # ln -s /moxa/mxser/driver/mxser.c mxser.c

316 317 318
       3.5.3 Add CAP address list for ISA boards. For PCI boards user,
          please skip this step.

Linus Torvalds's avatar
Linus Torvalds committed
319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339
	  In module mode, the CAP address for ISA board is given by
	  parameter. In static driver configuration, you'll have to
	  assign it within driver's source code. If you will not
	  install any ISA boards, you may skip to next portion.
	  The instructions to modify driver source code are as
	  below.
	  a. # cd /moxa/mxser/driver
	     # vi mxser.c
	  b. Find the array mxserBoardCAP[] as below.

	     static int mxserBoardCAP[]
	     = {0x00, 0x00, 0x00, 0x00};

	  c. Change the address within this array using vi. For
	     example, to driver 2 ISA boards with CAP address
	     0x280 and 0x180 as 1st and 2nd board. Just to change
	     the source code as follows.

	     static int mxserBoardCAP[]
	     = {0x280, 0x180, 0x00, 0x00};

340
       3.5.4 Setup kernel configuration
Linus Torvalds's avatar
Linus Torvalds committed
341

342
          Configure the kernel:
Linus Torvalds's avatar
Linus Torvalds committed
343

344 345
            # cd /usr/src/linux
            # make menuconfig
Linus Torvalds's avatar
Linus Torvalds committed
346

347 348 349 350
          You will go into a menu-driven system. Please select [Character
          devices][Non-standard serial port support], enable the [Moxa
          SmartIO support] driver with "[*]" for built-in (not "[M]"), then
          select [Exit] to exit this program.
Linus Torvalds's avatar
Linus Torvalds committed
351

352 353 354
       3.5.5 Rebuild kernel
	  The following are for Linux kernel rebuilding, for your
          reference only.
Linus Torvalds's avatar
Linus Torvalds committed
355 356 357
	  For appropriate details, please refer to the Linux document.

	   a. cd /usr/src/linux
358 359 360 361
	   b. make clean	     /* take a few minutes */
	   c. make dep		     /* take a few minutes */
	   d. make bzImage	     /* take probably 10-20 minutes */
	   e. make install	     /* copy boot image to correct position */
Linus Torvalds's avatar
Linus Torvalds committed
362
	   f. Please make sure the boot kernel (vmlinuz) is in the
363 364 365 366 367 368 369 370 371 372 373 374
	      correct position.
	   g. If you use 'lilo' utility, you should check /etc/lilo.conf
	      'image' item specified the path which is the 'vmlinuz' path,
	      or you will load wrong (or old) boot kernel image (vmlinuz).
	      After checking /etc/lilo.conf, please run "lilo".

	  Note that if the result of "make bzImage" is ERROR, then you have to
	  go back to Linux configuration Setup. Type "make menuconfig" in
          directory /usr/src/linux.


       3.5.6 Make tty device and special file
Linus Torvalds's avatar
Linus Torvalds committed
375 376 377
          # cd /moxa/mxser/driver
          # ./msmknod

378 379 380 381 382
       3.5.7 Make utility
	  # cd /moxa/mxser/utility
	  # make clean; make install

       3.5.8 Reboot
Linus Torvalds's avatar
Linus Torvalds committed
383

384 385 386


   3.6 Custom configuration
Linus Torvalds's avatar
Linus Torvalds committed
387
       Although this driver already provides you default configuration, you
388
       still can change the device name and major number. The instruction to
Linus Torvalds's avatar
Linus Torvalds committed
389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405
       change these parameters are shown as below.

       Change Device name
       ------------------
       If you'd like to use other device names instead of default naming
       convention, all you have to do is to modify the internal code
       within the shell script "msmknod". First, you have to open "msmknod"
       by vi. Locate each line contains "ttyM" and "cum" and change them
       to the device name you desired. "msmknod" creates the device names
       you need next time executed.

       Change Major number
       -------------------
       If major number 30 and 35 had been occupied, you may have to select
       2 free major numbers for this driver. There are 3 steps to change
       major numbers.

406
       3.6.1 Find free major numbers
Linus Torvalds's avatar
Linus Torvalds committed
407 408 409
	  In /proc/devices, you may find all the major numbers occupied
	  in the system. Please select 2 major numbers that are available.
	  e.g. 40, 45.
410
       3.6.2 Create special files
Linus Torvalds's avatar
Linus Torvalds committed
411 412
	  Run /moxa/mxser/driver/msmknod to create special files with
	  specified major numbers.
413
       3.6.3 Modify driver with new major number
Linus Torvalds's avatar
Linus Torvalds committed
414 415 416 417
	  Run vi to open /moxa/mxser/driver/mxser.c. Locate the line
	  contains "MXSERMAJOR". Change the content as below.
	  #define	  MXSERMAJOR		  40
	  #define	  MXSERCUMAJOR		  45
418
       3.6.4 Run "make clean; make install" in /moxa/mxser/driver.
Linus Torvalds's avatar
Linus Torvalds committed
419

420
   3.7 Verify driver installation
Linus Torvalds's avatar
Linus Torvalds committed
421 422
       You may refer to /var/log/messages to check the latest status
       log reported by this driver whenever it's activated.
423

Linus Torvalds's avatar
Linus Torvalds committed
424 425 426 427 428 429
-----------------------------------------------------------------------------
4. Utilities
   There are 3 utilities contained in this driver. They are msdiag, msmon and
   msterm. These 3 utilities are released in form of source code. They should
   be compiled into executable file and copied into /usr/bin.

430 431 432
   Before using these utilities, please load driver (refer 3.4 & 3.5) and
   make sure you had run the "msmknod" utility.

Linus Torvalds's avatar
Linus Torvalds committed
433 434
   msdiag - Diagnostic
   --------------------
435 436
   This utility provides the function to display what Moxa Smartio/Industio
   board found by driver in the system.
Linus Torvalds's avatar
Linus Torvalds committed
437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456

   msmon - Port Monitoring
   -----------------------
   This utility gives the user a quick view about all the MOXA ports'
   activities. One can easily learn each port's total received/transmitted
   (Rx/Tx) character count since the time when the monitoring is started.
   Rx/Tx throughputs per second are also reported in interval basis (e.g.
   the last 5 seconds) and in average basis (since the time the monitoring
   is started). You can reset all ports' count by <HOME> key. <+> <->
   (plus/minus) keys to change the displaying time interval. Press <ENTER>
   on the port, that cursor stay, to view the port's communication
   parameters, signal status, and input/output queue.

   msterm - Terminal Emulation
   ---------------------------
   This utility provides data sending and receiving ability of all tty ports,
   especially for MOXA ports. It is quite useful for testing simple
   application, for example, sending AT command to a modem connected to the
   port or used as a terminal for login purpose. Note that this is only a
   dumb terminal emulation without handling full screen operation.
457

Linus Torvalds's avatar
Linus Torvalds committed
458 459 460 461 462
-----------------------------------------------------------------------------
5. Setserial

   Supported Setserial parameters are listed as below.

463
   uart		  set UART type(16450-->disable FIFO, 16550A-->enable FIFO)
Linus Torvalds's avatar
Linus Torvalds committed
464 465 466 467 468 469 470
   close_delay	  set the amount of time(in 1/100 of a second) that DTR
		  should be kept low while being closed.
   closing_wait   set the amount of time(in 1/100 of a second) that the
		  serial port should wait for data to be drained while
		  being closed, before the receiver is disable.
   spd_hi	  Use  57.6kb  when  the application requests 38.4kb.
   spd_vhi	  Use  115.2kb	when  the application requests 38.4kb.
471 472
   spd_shi	  Use  230.4kb	when  the application requests 38.4kb.
   spd_warp	  Use  460.8kb	when  the application requests 38.4kb.
Linus Torvalds's avatar
Linus Torvalds committed
473
   spd_normal	  Use  38.4kb  when  the application requests 38.4kb.
474 475
   spd_cust	  Use  the custom divisor to set the speed when  the
		  application requests 38.4kb.
Lucas De Marchi's avatar
Lucas De Marchi committed
476
   divisor	  This option set the custom division.
477
   baud_base	  This option set the base baud rate.
Linus Torvalds's avatar
Linus Torvalds committed
478 479 480 481 482 483 484 485

-----------------------------------------------------------------------------
6. Troubleshooting

   The boot time error messages and solutions are stated as clearly as
   possible. If all the possible solutions fail, please contact our technical
   support team to get more help.

486 487 488

   Error msg: More than 4 Moxa Smartio/Industio family boards found. Fifth board
              and after are ignored.
Linus Torvalds's avatar
Linus Torvalds committed
489 490 491 492 493 494 495
   Solution:
   To avoid this problem, please unplug fifth and after board, because Moxa
   driver supports up to 4 boards.

   Error msg: Request_irq fail, IRQ(?) may be conflict with another device.
   Solution:
   Other PCI or ISA devices occupy the assigned IRQ. If you are not sure
496
   which device causes the situation, please check /proc/interrupts to find
Linus Torvalds's avatar
Linus Torvalds committed
497 498 499 500 501 502 503 504 505 506 507 508
   free IRQ and simply change another free IRQ for Moxa board.

   Error msg: Board #: C1xx Series(CAP=xxx) interrupt number invalid.
   Solution:
   Each port within the same multiport board shares the same IRQ. Please set
   one IRQ (IRQ doesn't equal to zero) for one Moxa board.

   Error msg: No interrupt vector be set for Moxa ISA board(CAP=xxx).
   Solution:
   Moxa ISA board needs an interrupt vector.Please refer to user's manual
   "Hardware Installation" chapter to set interrupt vector.

509
   Error msg: Couldn't install MOXA Smartio/Industio family driver!
Linus Torvalds's avatar
Linus Torvalds committed
510 511
   Solution:
   Load Moxa driver fail, the major number may conflict with other devices.
512
   Please refer to previous section 3.7 to change a free major number for
Linus Torvalds's avatar
Linus Torvalds committed
513 514
   Moxa driver.

515
   Error msg: Couldn't install MOXA Smartio/Industio family callout driver!
Linus Torvalds's avatar
Linus Torvalds committed
516 517
   Solution:
   Load Moxa callout driver fail, the callout device major number may
518
   conflict with other devices. Please refer to previous section 3.7 to
Linus Torvalds's avatar
Linus Torvalds committed
519
   change a free callout device major number for Moxa driver.
520 521


Linus Torvalds's avatar
Linus Torvalds committed
522
-----------------------------------------------------------------------------
523