karef.c 18.5 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
/*
 *  Copyright (C) 2005 Sandburst Corporation
 *  Travis B. Sawyer
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <config.h>
#include <common.h>
#include <command.h>
#include "karef.h"
#include "karef_version.h"
29
#include <timestamp.h>
30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
#include <asm/processor.h>
#include <asm/io.h>
#include <spd_sdram.h>
#include <i2c.h>
#include "../common/sb_common.h"
#include "../common/ppc440gx_i2c.h"

void fpga_init (void);

KAREF_BOARD_ID_ST board_id_as[] =
{
	{"Undefined"},			     /* Not specified */
	{"Kamino Reference Design"},
	{"Reserved"},			     /* Reserved for future use */
	{"Reserved"},			     /* Reserved for future use */
};

KAREF_BOARD_ID_ST ofem_board_id_as[] =
{
	{"Undefined"},
	{"1x10 + 10x2"},
	{"Reserved"},
	{"Reserved"},
};

/*************************************************************************
 *  board_early_init_f
 *
 *  Setup chip selects, initialize the Opto-FPGA, initialize
 *  interrupt polarity and triggers.
 ************************************************************************/
int board_early_init_f (void)
{
	ppc440_gpio_regs_t *gpio_regs;

	/* Enable GPIO interrupts */
	mtsdr(sdr_pfc0, 0x00103E00);

	/* Setup access for LEDs, and system topology info */
69
	gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
	gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS;
	gpio_regs->tri_state  = SBCOMMON_GPIO_DBGLEDS;

	/* Turn on all the leds for now */
	gpio_regs->out = SBCOMMON_GPIO_LEDS;

	/*--------------------------------------------------------------------+
	  | Initialize EBC CONFIG
	  +-------------------------------------------------------------------*/
	mtebc(xbcfg,
	      EBC_CFG_LE_UNLOCK	   | EBC_CFG_PTD_ENABLE |
	      EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS |
	      EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS |
	      EBC_CFG_EMC_DEFAULT  | EBC_CFG_PME_DISABLE |
	      EBC_CFG_PR_32);

	/*--------------------------------------------------------------------+
	  | 1/2 MB FLASH. Initialize bank 0 with default values.
	  +-------------------------------------------------------------------*/
	mtebc(pb0ap,
	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
	      EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) |
	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
	      EBC_BXAP_PEN_DISABLED);

97
	mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
	/*--------------------------------------------------------------------+
	  | 8KB NVRAM/RTC. Initialize bank 1 with default values.
	  +-------------------------------------------------------------------*/
	mtebc(pb1ap,
	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) |
	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
	      EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) |
	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
	      EBC_BXAP_PEN_DISABLED);

	mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);

	/*--------------------------------------------------------------------+
	  | Compact Flash, uses 2 Chip Selects (2 & 6)
	  +-------------------------------------------------------------------*/
	mtebc(pb2ap,
	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
	      EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) |
	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
	      EBC_BXAP_PEN_DISABLED);

	mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xF0000000) |
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);

	/*--------------------------------------------------------------------+
	  | KaRef Scan FPGA. Initialize bank 3 with default values.
	  +-------------------------------------------------------------------*/
	mtebc(pb5ap,
	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);

	mtebc(pb5cr, EBC_BXCR_BAS_ENCODE(0x48200000) |
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);

	/*--------------------------------------------------------------------+
	  | MAC A & B for Kamino.  OFEM FPGA decodes the addresses
	  | Initialize bank 4 with default values.
	  +-------------------------------------------------------------------*/
	mtebc(pb4ap,
	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);

	mtebc(pb4cr, EBC_BXCR_BAS_ENCODE(0x48600000) |
	      EBC_BXCR_BS_2MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);

	/*--------------------------------------------------------------------+
	  | OFEM FPGA  Initialize bank 5 with default values.
	  +-------------------------------------------------------------------*/
	mtebc(pb3ap,
	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);


	mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48400000) |
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);


	/*--------------------------------------------------------------------+
	  | Compact Flash, uses 2 Chip Selects (2 & 6)
	  +-------------------------------------------------------------------*/
	mtebc(pb6ap,
	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
	      EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) |
	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
	      EBC_BXAP_PEN_DISABLED);

	mtebc(pb6cr, EBC_BXCR_BAS_ENCODE(0xF0100000) |
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);

	/*--------------------------------------------------------------------+
	  | BME-32. Initialize bank 7 with default values.
	  +-------------------------------------------------------------------*/
	mtebc(pb7ap,
	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);

	mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48500000) |
	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);

	/*--------------------------------------------------------------------+
	 * Setup the interrupt controller polarities, triggers, etc.
	 +-------------------------------------------------------------------*/
199 200 201 202 203 204 205 206 207 208 209 210
	/*
	 * Because of the interrupt handling rework to handle 440GX interrupts
	 * with the common code, we needed to change names of the UIC registers.
	 * Here the new relationship:
	 *
	 * U-Boot name	440GX name
	 * -----------------------
	 * UIC0		UICB0
	 * UIC1		UIC0
	 * UIC2		UIC1
	 * UIC3		UIC2
	 */
211 212
	mtdcr (uic1sr, 0xffffffff);	/* clear all */
	mtdcr (uic1er, 0x00000000);	/* disable all */
213 214 215
	mtdcr (uic1cr, 0x00000000);	/* all non- critical */
	mtdcr (uic1pr, 0xfffffe03);	/* polarity */
	mtdcr (uic1tr, 0x01c00000);	/* trigger edge vs level */
216 217 218 219 220 221
	mtdcr (uic1vr, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr (uic1sr, 0xffffffff);	/* clear all */

	mtdcr (uic2sr, 0xffffffff);	/* clear all */
	mtdcr (uic2er, 0x00000000);	/* disable all */
	mtdcr (uic2cr, 0x00000000);	/* all non-critical */
222 223
	mtdcr (uic2pr, 0xffffc8ff);	/* polarity */
	mtdcr (uic2tr, 0x00ff0000);	/* trigger edge vs level */
224 225 226
	mtdcr (uic2vr, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr (uic2sr, 0xffffffff);	/* clear all */

227 228 229 230 231 232 233 234 235 236 237 238 239 240
	mtdcr (uic3sr, 0xffffffff);	/* clear all */
	mtdcr (uic3er, 0x00000000);	/* disable all */
	mtdcr (uic3cr, 0x00000000);	/* all non-critical */
	mtdcr (uic3pr, 0xffff83ff);	/* polarity */
	mtdcr (uic3tr, 0x00ff8c0f);	/* trigger edge vs level */
	mtdcr (uic3vr, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr (uic3sr, 0xffffffff);	/* clear all */

	mtdcr (uic0sr, 0xfc000000);	/* clear all */
	mtdcr (uic0er, 0x00000000);	/* disable all */
	mtdcr (uic0cr, 0x00000000);	/* all non-critical */
	mtdcr (uic0pr, 0xfc000000);
	mtdcr (uic0tr, 0x00000000);
	mtdcr (uic0vr, 0x00000001);
241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257

	fpga_init();

	return 0;
}


/*************************************************************************
 *  checkboard
 *
 *  Dump pertinent info to the console
 ************************************************************************/
int checkboard (void)
{
	sys_info_t sysinfo;
	unsigned char brd_rev, brd_id;
	unsigned short sernum;
258
	unsigned char scan_rev, scan_id, ofem_rev=0, ofem_id=0;
259 260 261 262
	unsigned char ofem_brd_rev, ofem_brd_id;
	KAREF_FPGA_REGS_ST *karef_ps;
	OFEM_FPGA_REGS_ST *ofem_ps;

263 264
	karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
	ofem_ps = (OFEM_FPGA_REGS_ST *)CONFIG_SYS_OFEM_FPGA_BASE;
265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302

	scan_id = (unsigned char)((karef_ps->revision_ul &
				   SAND_HAL_KA_SC_SCAN_REVISION_IDENTIFICATION_MASK)
				  >> SAND_HAL_KA_SC_SCAN_REVISION_IDENTIFICATION_SHIFT);

	scan_rev = (unsigned char)((karef_ps->revision_ul & SAND_HAL_KA_SC_SCAN_REVISION_REVISION_MASK)
				   >> SAND_HAL_KA_SC_SCAN_REVISION_REVISION_SHIFT);

	brd_rev = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_REV_MASK)
				  >> SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_REV_SHIFT);

	brd_id = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_ID_MASK)
				 >> SAND_HAL_KA_SC_SCAN_BRD_INFO_BRD_ID_SHIFT);

	ofem_brd_id = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_MASK)
				      >> SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_SHIFT);

	ofem_brd_rev = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_REV_MASK)
				       >> SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_REV_SHIFT);

	if (0xF != ofem_brd_id) {
		ofem_id = (unsigned char)((ofem_ps->revision_ul &
					   SAND_HAL_KA_OF_OFEM_REVISION_IDENTIFICATION_MASK)
					  >> SAND_HAL_KA_OF_OFEM_REVISION_IDENTIFICATION_SHIFT);

		ofem_rev = (unsigned char)((ofem_ps->revision_ul &
					    SAND_HAL_KA_OF_OFEM_REVISION_REVISION_MASK)
					   >> SAND_HAL_KA_OF_OFEM_REVISION_REVISION_SHIFT);
	}

	get_sys_info (&sysinfo);

	sernum = sbcommon_get_serial_number();

	printf ("Board: Sandburst Corporation Kamino Reference Design "
		"Serial Number: %d\n", sernum);
	printf ("%s\n", KAREF_U_BOOT_REL_STR);

303
	printf ("Built %s %s by %s\n", U_BOOT_DATE, U_BOOT_TIME, BUILDUSER);
304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322
	if (sbcommon_get_master()) {
		printf("Slot 0 - Master\nSlave board");
		if (sbcommon_secondary_present())
			printf(" present\n");
		else
			printf(" not detected\n");
	} else {
		printf("Slot 1 - Slave\n\n");
	}

	printf ("ScanFPGA ID:\t0x%02X\tRev:  0x%02X\n", scan_id, scan_rev);
	printf ("Board Rev:\t0x%02X\tID:   0x%02X\n", brd_rev, brd_id);
	if(0xF != ofem_brd_id) {
		printf("OFemFPGA ID:\t0x%02X\tRev:  0x%02X\n", ofem_id, ofem_rev);
		printf("OFEM Board Rev:\t0x%02X\tID:   0x%02X\n", ofem_brd_id, ofem_brd_rev);
	}

	/* Fix the ack in the bme 32 */
	udelay(5000);
323
	out32(CONFIG_SYS_BME32_BASE + 0x0000000C, 0x00000001);
324 325 326 327 328 329 330 331 332 333 334 335 336 337 338
	asm("eieio");


	return (0);
}

/*************************************************************************
 *  misc_init_f
 *
 *  Initialize I2C bus one to gain access to the fans
 ************************************************************************/
int misc_init_f (void)
{
	/* Turn on i2c bus 1 */
	puts ("I2C1:  ");
339
	i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
340 341 342 343 344 345 346
	puts ("ready\n");

	/* Turn on fans 3 & 4 */
	sbcommon_fans();

	return (0);
}
Wolfgang Denk's avatar
Wolfgang Denk committed
347

348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369
/*************************************************************************
 *  misc_init_r
 *
 *  Do nothing.
 ************************************************************************/
int misc_init_r (void)
{
	unsigned short sernum;
	char envstr[255];
	KAREF_FPGA_REGS_ST *karef_ps;
	OFEM_FPGA_REGS_ST *ofem_ps;

	if(NULL != getenv("secondserial")) {
		puts("secondserial is set, switching to second serial port\n");
		setenv("stderr", "serial1");
		setenv("stdout", "serial1");
		setenv("stdin", "serial1");
	}

	setenv("ubrelver", KAREF_U_BOOT_REL_STR);

	memset(envstr, 0, 255);
370 371
	sprintf (envstr, "Built %s %s by %s",
		 U_BOOT_DATE, U_BOOT_TIME, BUILDUSER);
372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401
	setenv("bldstr", envstr);
	saveenv();

	if( getenv("autorecover")) {
		setenv("autorecover", NULL);
		saveenv();
		sernum = sbcommon_get_serial_number();

		printf("\nSetting up environment for automatic filesystem recovery\n");
		/*
		 * Setup default bootargs
		 */
		memset(envstr, 0, 255);

		sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 "
			"rw ip=10.100.70.%d:::255.255.0.0:karef%d:eth0:none idebus=33",
			sernum, sernum);
		setenv("bootargs", envstr);

		/*
		 * Setup Default boot command
		 */
		setenv("bootcmd", "fatload ide 0 8000000 uimage.karef;"
		       "fatload ide 0 8100000 pramdisk;"
		       "bootm 8000000 8100000");

		printf("Done.  Please type allow the system to continue to boot\n");
	}

	if( getenv("fakeled")) {
402 403
		karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
		ofem_ps = (OFEM_FPGA_REGS_ST *)CONFIG_SYS_OFEM_FPGA_BASE;
404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421
		ofem_ps->control_ul &= ~SAND_HAL_KA_SC_SCAN_CNTL_FAULT_LED_MASK;
		karef_ps->control_ul &= ~SAND_HAL_KA_OF_OFEM_CNTL_FAULT_LED_MASK;
		setenv("bootdelay", "-1");
		saveenv();
		printf("fakeled is set. use 'setenv fakeled ; setenv bootdelay 5 ; saveenv' to recover\n");
	}

	return (0);
}

/*************************************************************************
 *  ide_set_reset
 ************************************************************************/
#ifdef CONFIG_IDE_RESET
void ide_set_reset(int on)
{
	KAREF_FPGA_REGS_ST *karef_ps;
	/* TODO: ide reset */
422
	karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444

	if (on) {
		karef_ps->reset_ul &= ~SAND_HAL_KA_SC_SCAN_RESET_CF_RESET_N_MASK;
	} else {
		karef_ps->reset_ul |= SAND_HAL_KA_SC_SCAN_RESET_CF_RESET_N_MASK;
	}
}
#endif /* CONFIG_IDE_RESET */

/*************************************************************************
 *  fpga_init
 ************************************************************************/
void fpga_init(void)
{
	KAREF_FPGA_REGS_ST *karef_ps;
	OFEM_FPGA_REGS_ST *ofem_ps;
	unsigned char ofem_id;
	unsigned long tmp;

	/* Ensure we have power all around */
	udelay(500);

445
	karef_ps = (KAREF_FPGA_REGS_ST *)CONFIG_SYS_KAREF_FPGA_BASE;
446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474
	tmp =
		SAND_HAL_KA_SC_SCAN_RESET_CF_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_BME_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_KA_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_SLAVE_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_OFEM_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_IFE_A_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_I2C_MUX1_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_PHY0_RESET_N_MASK |
		SAND_HAL_KA_SC_SCAN_RESET_PHY1_RESET_N_MASK;

	karef_ps->reset_ul = tmp;

	/*
	 * Wait a bit to allow the ofem fpga to get its brains
	 */
	udelay(5000);

	/*
	 * Check to see if the ofem is there
	 */
	ofem_id = (unsigned char)((karef_ps->boardinfo_ul & SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_MASK)
				  >> SAND_HAL_KA_SC_SCAN_BRD_INFO_FEM_ID_SHIFT);
	if(0xF != ofem_id) {
		tmp =
			SAND_HAL_KA_OF_OFEM_RESET_I2C_MUX0_RESET_N_MASK |
			SAND_HAL_KA_OF_OFEM_RESET_LOCH0_RESET_N_MASK |
			SAND_HAL_KA_OF_OFEM_RESET_MAC0_RESET_N_MASK;

475
		ofem_ps = (OFEM_FPGA_REGS_ST *)CONFIG_SYS_OFEM_FPGA_BASE;
476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584
		ofem_ps->reset_ul = tmp;

		ofem_ps->control_ul |= 1 < SAND_HAL_KA_OF_OFEM_CNTL_FAULT_LED_SHIFT;
	}

	karef_ps->control_ul |= 1 << SAND_HAL_KA_SC_SCAN_CNTL_FAULT_LED_SHIFT;

	asm("eieio");

	return;
}

int karefSetupVars(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
	unsigned short sernum;
	char envstr[255];

	sernum = sbcommon_get_serial_number();

	memset(envstr, 0, 255);
	/*
	 * Setup our ip address
	 */
	sprintf(envstr, "10.100.70.%d", sernum);

	setenv("ipaddr", envstr);
	/*
	 * Setup the host ip address
	 */
	setenv("serverip", "10.100.17.10");

	/*
	 * Setup default bootargs
	 */
	memset(envstr, 0, 255);

	sprintf(envstr, "console=ttyS0,9600 root=/dev/nfs "
		"rw nfsroot=10.100.17.10:/home/metrobox/mbc70.%d "
		"nfsaddrs=10.100.70.%d:10.100.17.10:10.100.1.1:"
		"255.255.0.0:karef%d.sandburst.com:eth0:none idebus=33",
		sernum, sernum, sernum);

	setenv("bootargs_nfs", envstr);
	setenv("bootargs", envstr);

	/*
	 * Setup CF bootargs
	 */
	memset(envstr, 0, 255);

	sprintf(envstr, "console=ttyS0,9600 root=/dev/hda2 "
		"rw ip=10.100.70.%d:::255.255.0.0:karef%d:eth0:none idebus=33",
		sernum, sernum);

	setenv("bootargs_cf", envstr);

	/*
	 * Setup Default boot command
	 */
	setenv("bootcmd_tftp", "tftp 8000000 uImage.karef;bootm 8000000");
	setenv("bootcmd", "tftp 8000000 uImage.karef;bootm 8000000");

	/*
	 * Setup compact flash boot command
	 */
	setenv("bootcmd_cf", "fatload ide 0 8000000 uimage.karef;bootm 8000000");

	saveenv();

	return(1);
}

int karefRecover(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
	unsigned short sernum;
	char envstr[255];

	sernum = sbcommon_get_serial_number();

	printf("\nSetting up environment for filesystem recovery\n");
	/*
	 * Setup default bootargs
	 */
	memset(envstr, 0, 255);

	sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 "
		"rw ip=10.100.70.%d:::255.255.0.0:karef%d:eth0:none",
		sernum, sernum);
	setenv("bootargs", envstr);

	/*
	 * Setup Default boot command
	 */

	setenv("bootcmd", "fatload ide 0 8000000 uimage.karef;"
	       "fatload ide 0 8100000 pramdisk;"
	       "bootm 8000000 8100000");

	printf("Done.  Please type boot<cr>.\nWhen the kernel has booted"
	       " please type fsrecover.sh<cr>\n");

	return(1);
}

U_BOOT_CMD(kasetup, 1, 1, karefSetupVars,
	   "kasetup - Set environment to factory defaults\n", NULL);

U_BOOT_CMD(karecover, 1, 1, karefRecover,
	   "karecover - Set environment to allow for fs recovery\n", NULL);