x600.c 2.43 KB
Newer Older
1 2 3 4 5 6
/*
 * (C) Copyright 2009
 * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
 *
 * Copyright (C) 2012 Stefan Roese <sr@denx.de>
 *
7
 * SPDX-License-Identifier:	GPL-2.0+
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69
 */

#include <common.h>
#include <nand.h>
#include <netdev.h>
#include <phy.h>
#include <rtc.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/spr_defs.h>
#include <asm/arch/spr_misc.h>
#include <linux/mtd/fsmc_nand.h>
#include "fpga.h"

static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE];

int board_init(void)
{
	/*
	 * X600 is equipped with an M41T82 RTC. This RTC has the
	 * HT bit (Halt Update), which needs to be cleared upon
	 * power-up. Otherwise the RTC is halted.
	 */
	rtc_reset();

	return spear_board_init(MACH_TYPE_SPEAR600);
}

int board_late_init(void)
{
	/*
	 * Monitor and env protection on by default
	 */
	flash_protect(FLAG_PROTECT_SET,
		      CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE +
		      CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN +
		      2 * CONFIG_ENV_SECT_SIZE - 1,
		      &flash_info[0]);

	/* Init FPGA subsystem */
	x600_init_fpga();

	return 0;
}

/*
 * board_nand_init - Board specific NAND initialization
 * @nand:	mtd private chip structure
 *
 * Called by nand_init_chip to initialize the board specific functions
 */

void board_nand_init(void)
{
	struct misc_regs *const misc_regs_p =
		(struct misc_regs *)CONFIG_SPEAR_MISCBASE;
	struct nand_chip *nand = &nand_chip[0];

	if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS))
		fsmc_nand_init(nand);
}

70
int board_phy_config(struct phy_device *phydev)
71 72
{
	/* Extended PHY control 1, select GMII */
73
	phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
74 75

	/* Software reset necessary after GMII mode selction */
76
	phy_reset(phydev);
77 78

	/* Enable extended page register access */
79
	phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
80 81

	/* 17e: Enhanced LED behavior, needs to be written twice */
82 83
	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
84 85

	/* 16e: Enhanced LED method select */
86
	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
87 88

	/* Disable extended page register access */
89
	phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
90 91

	/* Enable clock output pin */
92 93 94 95
	phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);

	if (phydev->drv->config)
		phydev->drv->config(phydev);
96 97 98 99 100 101 102 103

	return 0;
}

int board_eth_init(bd_t *bis)
{
	int ret = 0;

104
	if (designware_initialize(CONFIG_SPEAR_ETHBASE,
105 106 107 108 109
				  PHY_INTERFACE_MODE_GMII) >= 0)
		ret++;

	return ret;
}