cortina.c 8.92 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333
/*
 * Cortina CS4315/CS4340 10G PHY drivers
 *
 * SPDX-License-Identifier:     GPL-2.0+
 *
 * Copyright 2014 Freescale Semiconductor, Inc.
 *
 */

#include <config.h>
#include <common.h>
#include <malloc.h>
#include <linux/ctype.h>
#include <linux/string.h>
#include <linux/err.h>
#include <phy.h>
#include <cortina.h>
#ifdef CONFIG_SYS_CORTINA_FW_IN_NAND
#include <nand.h>
#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
#include <spi_flash.h>
#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
#include <mmc.h>
#endif

#ifndef CONFIG_PHYLIB_10G
#error The Cortina PHY needs 10G support
#endif

struct cortina_reg_config cortina_reg_cfg[] = {
	/* CS4315_enable_sr_mode */
	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
	{VILLA_MSEQ_OPTIONS, 0xf},
	{VILLA_MSEQ_PC, 0x0},
	{VILLA_MSEQ_BANKSELECT,	   0x4},
	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPA, 0x55},
	{VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER, 0x30},
	{VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT, 0x1},
	{VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT, 0x2},
	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPB, 0x2003},
	{VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL, 0xF047},
	{VILLA_MSEQ_ENABLE_MSB, 0x0000},
	{VILLA_MSEQ_SPARE21_LSB, 0x6},
	{VILLA_MSEQ_RESET_COUNT_LSB, 0x0},
	{VILLA_MSEQ_SPARE12_MSB, 0x0000},
	/*
	 * to invert the receiver path, uncomment the next line
	 * write (VILLA_MSEQ_SPARE12_MSB, 0x4000)
	 *
	 * SPARE2_LSB is used to configure the device while in sr mode to
	 * enable power savings and to use the optical module LOS signal.
	 * in power savings mode, the internal prbs checker can not be used.
	 * if the optical module LOS signal is used as an input to the micro
	 * code, then the micro code will wait until the optical module
	 * LOS = 0 before turning on the adaptive equalizer.
	 * Setting SPARE2_LSB bit 0 to 1 places the devie in power savings mode
	 * while setting bit 0 to 0 disables power savings mode.
	 * Setting SPARE2_LSB bit 2 to 0 configures the device to use the
	 * optical module LOS signal while setting bit 2 to 1 configures the
	 * device so that it will ignore the optical module LOS SPARE2_LSB = 0
	 */

	/* enable power savings, ignore optical module LOS */
	{VILLA_MSEQ_SPARE2_LSB, 0x5},

	{VILLA_MSEQ_SPARE7_LSB, 0x1e},
	{VILLA_MSEQ_BANKSELECT, 0x4},
	{VILLA_MSEQ_SPARE9_LSB, 0x2},
	{VILLA_MSEQ_SPARE3_LSB, 0x0F53},
	{VILLA_MSEQ_SPARE3_MSB, 0x2006},
	{VILLA_MSEQ_SPARE8_LSB, 0x3FF7},
	{VILLA_MSEQ_SPARE8_MSB, 0x0A46},
	{VILLA_MSEQ_COEF8_FFE0_LSB, 0xD500},
	{VILLA_MSEQ_COEF8_FFE1_LSB, 0x0200},
	{VILLA_MSEQ_COEF8_FFE2_LSB, 0xBA00},
	{VILLA_MSEQ_COEF8_FFE3_LSB, 0x0100},
	{VILLA_MSEQ_COEF8_FFE4_LSB, 0x0300},
	{VILLA_MSEQ_COEF8_FFE5_LSB, 0x0300},
	{VILLA_MSEQ_COEF8_DFE0_LSB, 0x0700},
	{VILLA_MSEQ_COEF8_DFE0N_LSB, 0x0E00},
	{VILLA_MSEQ_COEF8_DFE1_LSB, 0x0B00},
	{VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK, 0x2},
	{VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB, 0xD000},
	{VILLA_MSEQ_POWER_DOWN_LSB, 0xFFFF},
	{VILLA_MSEQ_POWER_DOWN_MSB, 0x0},
	{VILLA_MSEQ_CAL_RX_SLICER, 0x80},
	{VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB, 0x3f},
	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
	{VILLA_MSEQ_OPTIONS, 0x7},

	/* set up min value for ffe1 */
	{VILLA_MSEQ_COEF_INIT_SEL, 0x2},
	{VILLA_DSP_SDS_DSP_PRECODEDINITFFE21, 0x41},

	/* CS4315_sr_rx_pre_eq_set_4in */
	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
	{VILLA_MSEQ_OPTIONS, 0xf},
	{VILLA_MSEQ_BANKSELECT, 0x4},
	{VILLA_MSEQ_PC, 0x0},

	/* for lengths from 3.5 to 4.5inches */
	{VILLA_MSEQ_SERDES_PARAM_LSB, 0x0306},
	{VILLA_MSEQ_SPARE25_LSB, 0x0306},
	{VILLA_MSEQ_SPARE21_LSB, 0x2},
	{VILLA_MSEQ_SPARE23_LSB, 0x2},
	{VILLA_MSEQ_CAL_RX_DFE_EQ, 0x0},

	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
	{VILLA_MSEQ_OPTIONS, 0x7},

	/* CS4315_rx_drive_4inch */
	/* for length  4inches */
	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
	{VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},

	/* CS4315_tx_drive_4inch */
	/* for length  4inches */
	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
};

void cs4340_upload_firmware(struct phy_device *phydev)
{
	char line_temp[0x50] = {0};
	char reg_addr[0x50] = {0};
	char reg_data[0x50] = {0};
	int i, line_cnt = 0, column_cnt = 0;
	struct cortina_reg_config fw_temp;
	char *addr = NULL;

#if defined(CONFIG_SYS_CORTINA_FW_IN_NOR) || \
	defined(CONFIG_SYS_CORTINA_FW_IN_REMOTE)

	addr = (char *)CONFIG_CORTINA_FW_ADDR;
#elif defined(CONFIG_SYS_CORTINA_FW_IN_NAND)
	int ret;
	size_t fw_length = CONFIG_CORTINA_FW_LENGTH;

	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
	ret = nand_read(&nand_info[0], (loff_t)CONFIG_CORTINA_FW_ADDR,
		       &fw_length, (u_char *)addr);
	if (ret == -EUCLEAN) {
		printf("NAND read of Cortina firmware at 0x%x failed %d\n",
		       CONFIG_CORTINA_FW_ADDR, ret);
	}
#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
	int ret;
	struct spi_flash *ucode_flash;

	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
				CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
	if (!ucode_flash) {
		puts("SF: probe for Cortina ucode failed\n");
	} else {
		ret = spi_flash_read(ucode_flash, CONFIG_CORTINA_FW_ADDR,
				     CONFIG_CORTINA_FW_LENGTH, addr);
		if (ret)
			puts("SF: read for Cortina ucode failed\n");
		spi_flash_free(ucode_flash);
	}
#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
	int dev = CONFIG_SYS_MMC_ENV_DEV;
	u32 cnt = CONFIG_CORTINA_FW_LENGTH / 512;
	u32 blk = CONFIG_CORTINA_FW_ADDR / 512;
	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);

	if (!mmc) {
		puts("Failed to find MMC device for Cortina ucode\n");
	} else {
		addr = malloc(CONFIG_CORTINA_FW_LENGTH);
		printf("MMC read: dev # %u, block # %u, count %u ...\n",
		       dev, blk, cnt);
		mmc_init(mmc);
		(void)mmc->block_dev.block_read(dev, blk, cnt, addr);
		/* flush cache after read */
		flush_cache((ulong)addr, cnt * 512);
	}
#endif

	while (*addr != 'Q') {
		i = 0;

		while (*addr != 0x0a) {
			line_temp[i++] = *addr++;
			if (0x50 < i) {
				printf("Not found Cortina PHY ucode at 0x%x\n",
				       CONFIG_CORTINA_FW_ADDR);
				return;
			}
		}

		addr++;  /* skip '\n' */
		line_cnt++;
		column_cnt = i;
		line_temp[column_cnt] = '\0';

		if (CONFIG_CORTINA_FW_LENGTH < line_cnt)
			return;

		for (i = 0; i < column_cnt; i++) {
			if (isspace(line_temp[i++]))
				break;
		}

		memcpy(reg_addr, line_temp, i);
		memcpy(reg_data, &line_temp[i], column_cnt - i);
		strim(reg_addr);
		strim(reg_data);
		fw_temp.reg_addr = (simple_strtoul(reg_addr, NULL, 0)) & 0xffff;
		fw_temp.reg_value = (simple_strtoul(reg_data, NULL, 0)) &
				     0xffff;
		phy_write(phydev, 0x00, fw_temp.reg_addr, fw_temp.reg_value);
	}
}

int cs4340_phy_init(struct phy_device *phydev)
{
	int timeout = 100;  /* 100ms */
	int reg_value;

	/* step1: BIST test */
	phy_write(phydev, 0x00, VILLA_GLOBAL_MSEQCLKCTRL,     0x0004);
	phy_write(phydev, 0x00, VILLA_GLOBAL_LINE_SOFT_RESET, 0x0000);
	phy_write(phydev, 0x00, VILLA_GLOBAL_BIST_CONTROL,    0x0001);
	while (--timeout) {
		reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_BIST_STATUS);
		if (reg_value & mseq_edc_bist_done) {
			if (0 == (reg_value & mseq_edc_bist_fail))
				break;
		}
		udelay(1000);
	}

	if (!timeout) {
		printf("%s BIST mseq_edc_bist_done timeout!\n", __func__);
		return -1;
	}

	/* setp2: upload ucode */
	cs4340_upload_firmware(phydev);
	reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS);
	if (reg_value) {
		debug("%s checksum status failed.\n", __func__);
		return -1;
	}

	return 0;
}

int cs4340_config(struct phy_device *phydev)
{
	cs4340_phy_init(phydev);
	return 0;
}

int cs4340_startup(struct phy_device *phydev)
{
	phydev->link = 1;

	/* For now just lie and say it's 10G all the time */
	phydev->speed = SPEED_10000;
	phydev->duplex = DUPLEX_FULL;
	return 0;
}

struct phy_driver cs4340_driver = {
	.name = "Cortina CS4315/CS4340",
	.uid = PHY_UID_CS4340,
	.mask = 0xfffffff0,
	.features = PHY_10G_FEATURES,
	.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
		 MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
		 MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
	.config = &cs4340_config,
	.startup = &cs4340_startup,
	.shutdown = &gen10g_shutdown,
};

int phy_cortina_init(void)
{
	phy_register(&cs4340_driver);
	return 0;
}

int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
{
	int phy_reg;
	bool is_cortina_phy = false;

	switch (addr) {
#ifdef CORTINA_PHY_ADDR1
	case CORTINA_PHY_ADDR1:
#endif
#ifdef CORTINA_PHY_ADDR2
	case CORTINA_PHY_ADDR2:
#endif
#ifdef CORTINA_PHY_ADDR3
	case CORTINA_PHY_ADDR3:
#endif
#ifdef CORTINA_PHY_ADDR4
	case CORTINA_PHY_ADDR4:
#endif
		is_cortina_phy = true;
		break;
	default:
		break;
	}

	/* Cortina PHY has non-standard offset of PHY ID registers */
	if (is_cortina_phy)
		phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_LSB);
	else
		phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);

	if (phy_reg < 0)
		return -EIO;

	*phy_id = (phy_reg & 0xffff) << 16;
	if (is_cortina_phy)
		phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_MSB);
	else
		phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);

	if (phy_reg < 0)
		return -EIO;

	*phy_id |= (phy_reg & 0xffff);

	return 0;
}