Commit 1a02806c authored by Jean-Christophe PLAGNIOL-VILLARD's avatar Jean-Christophe PLAGNIOL-VILLARD
Browse files

drivers/block: Move conditional compilation to Makefile


Signed-off-by: default avatarJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
parent 1a6ffbfa
......@@ -25,14 +25,14 @@ include $(TOPDIR)/config.mk
LIB := $(obj)libblock.a
COBJS-y += ahci.o
COBJS-y += ata_piix.o
COBJS-$(CONFIG_SCSI_AHCI) += ahci.o
COBJS-$(CONFIG_ATA_PIIX) += ata_piix.o
COBJS-$(CONFIG_FSL_SATA) += fsl_sata.o
COBJS-$(CONFIG_LIBATA) += libata.o
COBJS-$(CONFIG_SATA_SIL3114) += sata_sil3114.o
COBJS-y += sil680.o
COBJS-y += sym53c8xx.o
COBJS-y += systemace.o
COBJS-$(CONFIG_IDE_SIL680) += sil680.o
COBJS-$(CONFIG_SCSI_SYM53C8XX) += sym53c8xx.o
COBJS-$(CONFIG_SYSTEMACE) += systemace.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
......
......@@ -26,8 +26,6 @@
*/
#include <common.h>
#ifdef CONFIG_SCSI_AHCI
#include <command.h>
#include <pci.h>
#include <asm/processor.h>
......@@ -700,4 +698,3 @@ void scsi_print_error(ccb * pccb)
{
/*The ahci error info can be read in the ahci driver*/
}
#endif
......@@ -35,8 +35,6 @@
#include <ide.h>
#include <ata.h>
#ifdef CFG_ATA_PIIX /*ata_piix driver */
extern block_dev_desc_t sata_dev_desc[CFG_SATA_MAX_DEVICE];
extern int curr_device;
......@@ -756,5 +754,3 @@ int scan_sata(int dev)
{
return 0;
}
#endif
......@@ -27,7 +27,7 @@
* The following parameters must be defined in the configuration file
* of the target board:
*
* #define CFG_IDE_SIL680
* #define CONFIG_IDE_SIL680
*
* #define CONFIG_PCI_PNP
* NOTE it may also be necessary to define this if the default of 8 is
......@@ -54,7 +54,6 @@
*/
#include <common.h>
#if defined(CFG_IDE_SIL680)
#include <ata.h>
#include <ide.h>
#include <pci.h>
......@@ -106,5 +105,3 @@ int ide_preinit (void)
void ide_set_reset (int flag) {
return;
}
#endif /* CFG_IDE_SIL680 */
......@@ -35,8 +35,6 @@
#include <common.h>
#ifdef CONFIG_SCSI_SYM53C8XX
#include <command.h>
#include <pci.h>
#include <asm/processor.h>
......@@ -870,6 +868,3 @@ void scsi_chip_init(void)
#endif
}
#endif
#endif /* CONFIG_SCSI_SYM53C8XX */
......@@ -44,8 +44,6 @@
#include <part.h>
#include <asm/io.h>
#ifdef CONFIG_SYSTEMACE
/*
* The ace_readw and writew functions read/write 16bit words, but the
* offset value is the BYTE offset as most used in the Xilinx
......@@ -255,4 +253,3 @@ static unsigned long systemace_read(int dev, unsigned long start,
return blkcnt;
}
#endif /* CONFIG_SYSTEMACE */
......@@ -178,7 +178,7 @@
#define CFG_SATA_MAXBUS 2 /*Max Sata buses supported */
#define CFG_SATA_DEVS_PER_BUS 2 /*Max no. of devices per bus/port */
#define CFG_SATA_MAX_DEVICE (CFG_SATA_MAXBUS* CFG_SATA_DEVS_PER_BUS)
#define CFG_ATA_PIIX 1 /*Supports ata_piix driver */
#define CONFIG_ATA_PIIX 1 /*Supports ata_piix driver */
/************************************************************
* DISK Partition support
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment