Commit 2a8c9c86 authored by Albert ARIBAUD's avatar Albert ARIBAUD

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

parents 015b18c6 3aae66e2
......@@ -10,6 +10,7 @@
#include <asm/io.h>
#include <common.h>
#include <asm/arch/ddr3.h>
#include <asm/arch/psc_defs.h>
void ddr3_init_ddrphy(u32 base, struct ddr3_phy_config *phy_cfg)
{
......@@ -86,3 +87,77 @@ void ddr3_reset_ddrphy(void)
tmp &= ~KS2_DDR3_PLLCTRL_PHY_RESET;
__raw_writel(tmp, KS2_DDR3APLLCTL1);
}
#ifdef CONFIG_SOC_K2HK
/**
* ddr3_reset_workaround - reset workaround in case if leveling error
* detected for PG 1.0 and 1.1 k2hk SoCs
*/
void ddr3_err_reset_workaround(void)
{
unsigned int tmp;
unsigned int tmp_a;
unsigned int tmp_b;
/*
* Check for PGSR0 error bits of DDR3 PHY.
* Check for WLERR, QSGERR, WLAERR,
* RDERR, WDERR, REERR, WEERR error to see if they are set or not
*/
tmp_a = __raw_readl(KS2_DDR3A_DDRPHYC + KS2_DDRPHY_PGSR0_OFFSET);
tmp_b = __raw_readl(KS2_DDR3B_DDRPHYC + KS2_DDRPHY_PGSR0_OFFSET);
if (((tmp_a & 0x0FE00000) != 0) || ((tmp_b & 0x0FE00000) != 0)) {
printf("DDR Leveling Error Detected!\n");
printf("DDR3A PGSR0 = 0x%x\n", tmp_a);
printf("DDR3B PGSR0 = 0x%x\n", tmp_b);
/*
* Write Keys to KICK registers to enable writes to registers
* in boot config space
*/
__raw_writel(KS2_KICK0_MAGIC, KS2_KICK0);
__raw_writel(KS2_KICK1_MAGIC, KS2_KICK1);
/*
* Move DDR3A Module out of reset isolation by setting
* MDCTL23[12] = 0
*/
tmp_a = __raw_readl(KS2_PSC_BASE +
PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3A));
tmp_a = PSC_REG_MDCTL_SET_RESET_ISO(tmp_a, 0);
__raw_writel(tmp_a, KS2_PSC_BASE +
PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3A));
/*
* Move DDR3B Module out of reset isolation by setting
* MDCTL24[12] = 0
*/
tmp_b = __raw_readl(KS2_PSC_BASE +
PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3B));
tmp_b = PSC_REG_MDCTL_SET_RESET_ISO(tmp_b, 0);
__raw_writel(tmp_b, KS2_PSC_BASE +
PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3B));
/*
* Write 0x5A69 Key to RSTCTRL[15:0] to unlock writes
* to RSTCTRL and RSTCFG
*/
tmp = __raw_readl(KS2_RSTCTRL);
tmp &= KS2_RSTCTRL_MASK;
tmp |= KS2_RSTCTRL_KEY;
__raw_writel(tmp, KS2_RSTCTRL);
/*
* Set PLL Controller to drive hard reset on SW trigger by
* setting RSTCFG[13] = 0
*/
tmp = __raw_readl(KS2_RSTCTRL_RSCFG);
tmp &= ~KS2_RSTYPE_PLL_SOFT;
__raw_writel(tmp, KS2_RSTCTRL_RSCFG);
reset_cpu(0);
}
}
#endif
......@@ -50,6 +50,7 @@ struct ddr3_emif_config {
void ddr3_init(void);
void ddr3_reset_ddrphy(void);
void ddr3_err_reset_workaround(void);
void ddr3_init_ddrphy(u32 base, struct ddr3_phy_config *phy_cfg);
void ddr3_init_ddremif(u32 base, struct ddr3_emif_config *emif_cfg);
......
......@@ -121,9 +121,11 @@ typedef volatile unsigned int *dv_reg_p;
#define KS2_CLOCK_BASE KS2_PLL_CNTRL_BASE
#define KS2_RSTCTRL_RSTYPE (KS2_PLL_CNTRL_BASE + 0xe4)
#define KS2_RSTCTRL (KS2_PLL_CNTRL_BASE + 0xe8)
#define KS2_RSTCTRL_RSCFG (KS2_PLL_CNTRL_BASE + 0xec)
#define KS2_RSTCTRL_KEY 0x5a69
#define KS2_RSTCTRL_MASK 0xffff0000
#define KS2_RSTCTRL_SWRST 0xfffe0000
#define KS2_RSTYPE_PLL_SOFT BIT(13)
/* SPI */
#define KS2_SPI0_BASE 0x21000400
......
......@@ -81,4 +81,8 @@ void ddr3_init(void)
while (1)
;
}
/* Apply the workaround for PG 1.0 and 1.1 Silicons */
if (cpu_revision() <= 1)
ddr3_err_reset_workaround();
}
......@@ -115,6 +115,9 @@
"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
"ip=dhcp\0" \
"bootenv=uEnv.txt\0" \
"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
"source ${loadaddr}\0" \
"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t -r $loadaddr $filesize\0" \
......@@ -142,17 +145,21 @@
"mmcboot=mmc dev ${mmcdev}; " \
"if mmc rescan; then " \
"echo SD/MMC found on device ${mmcdev};" \
"if run loadbootenv; then " \
"echo Loaded environment from ${bootenv};" \
"run importbootenv;" \
"fi;" \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...;" \
"run uenvcmd;" \
"fi;" \
"if run loadimage; then " \
"run mmcloados;" \
"fi;" \
"if run loadbootscript; then " \
"run bootscript;" \
"else " \
"if run loadbootenv; then " \
"echo Loaded environment from ${bootenv};" \
"run importbootenv;" \
"fi;" \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...;" \
"run uenvcmd;" \
"fi;" \
"if run loadimage; then " \
"run mmcloados;" \
"fi;" \
"fi ;" \
"fi;\0" \
"spiboot=echo Booting from spi ...; " \
"run spiargs; " \
......
......@@ -101,10 +101,10 @@
"vram=${vram} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
"source ${loadaddr}\0" \
"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
"loadbootenv=load mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
"importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
"env import -t ${loadaddr} ${filesize}\0" \
"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment