Commit 37d41632 authored by Wolfgang Denk's avatar Wolfgang Denk
Browse files

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

parents d3909d74 c7190f02
......@@ -2403,20 +2403,7 @@ MVBLM7_config: unconfig
sbc8349_config \
sbc8349_PCI_33_config \
sbc8349_PCI_66_config: unconfig
@mkdir -p $(obj)include
@if [ "$(findstring _PCI_,$@)" ] ; then \
$(XECHO) -n "... PCI HOST at " ; \
echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
fi ; \
if [ "$(findstring _33_,$@)" ] ; then \
$(XECHO) -n "33MHz... " ; \
echo "#define PCI_33M" >>$(obj)include/config.h ; \
fi ; \
if [ "$(findstring _66_,$@)" ] ; then \
$(XECHO) -n "66MHz... " ; \
echo "#define PCI_66M" >>$(obj)include/config.h ; \
fi ;
@$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349
@$(MKCONFIG) -t $(@:_config=) sbc8349 ppc mpc83xx sbc8349
SIMPC8313_LP_config \
SIMPC8313_SP_config: unconfig
......
......@@ -21,12 +21,16 @@
#endif
#include <spd_sdram.h>
#include <asm/mmu.h>
#include <asm/io.h>
#if defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
#endif
#include <hwconfig.h>
#include <fdt_support.h>
#if defined(CONFIG_PQ_MDS_PIB)
#include "../common/pq-mds-pib.h"
#endif
#include "../../../drivers/qe/uec.h"
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* GETH1 */
......@@ -89,11 +93,19 @@ const qe_iop_conf_t qe_iop_conf_tab[] = {
{0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */
};
int board_early_init_f(void)
/* Handle "mpc8360ea rev.2.1 erratum 2: RGMII Timing"? */
static int board_handle_erratum2(void)
{
const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
return REVID_MAJOR(immr->sysconf.spridr) == 2 &&
REVID_MINOR(immr->sysconf.spridr) == 1;
}
int board_early_init_f(void)
{
const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
/* Enable flash write */
bcsr[0xa] &= ~0x04;
......@@ -105,6 +117,21 @@ int board_early_init_f(void)
/* Enable second UART */
bcsr[0x9] &= ~0x01;
if (board_handle_erratum2()) {
void *immap = (immap_t *)(CONFIG_SYS_IMMR + 0x14a8);
/*
* IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
* IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
*/
setbits_be32(immap, 0x0c003000);
/*
* IMMR + 0x14AC[20:27] = 10101010
* (data delay for both UCC's)
*/
clrsetbits_be32(immap + 4, 0xff0, 0xaa0);
}
return 0;
}
......@@ -116,6 +143,28 @@ int board_early_init_r(void)
return 0;
}
#ifdef CONFIG_UEC_ETH
static uec_info_t uec_info[] = {
#ifdef CONFIG_UEC_ETH1
STD_UEC_INFO(1),
#endif
#ifdef CONFIG_UEC_ETH2
STD_UEC_INFO(2),
#endif
};
int board_eth_init(bd_t *bd)
{
if (board_handle_erratum2()) {
int i;
for (i = 0; i < ARRAY_SIZE(uec_info); i++)
uec_info[i].enet_interface = ENET_1000_RGMII_RXID;
}
return uec_eth_init(bd, uec_info, ARRAY_SIZE(uec_info));
}
#endif /* CONFIG_UEC_ETH */
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
......@@ -126,6 +175,7 @@ phys_size_t initdram(int board_type)
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
u32 msize = 0;
u32 lbc_sdram_size;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
return -1;
......@@ -147,7 +197,9 @@ phys_size_t initdram(int board_type)
/*
* Initialize SDRAM if it is on local bus.
*/
msize += sdram_init(msize * 1024 * 1024);
lbc_sdram_size = sdram_init(msize * 1024 * 1024);
if (!msize)
msize = lbc_sdram_size;
/* return total bus SDRAM size(bytes) -- DDR */
return (msize * 1024 * 1024);
......@@ -307,21 +359,28 @@ static int sdram_init(unsigned int base) { return 0; }
#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
static void ft_board_fixup_qe_usb(void *blob, bd_t *bd)
{
const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
if (!hwconfig_subarg_cmp("qe_usb", "mode", "peripheral"))
return;
do_fixup_by_compat(blob, "fsl,mpc8323-qe-usb", "mode",
"peripheral", sizeof("peripheral"), 1);
}
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
#endif
ft_board_fixup_qe_usb(blob, bd);
/*
* mpc8360ea pb mds errata 2: RGMII timing
* if on mpc8360ea rev. 2.1,
* change both ucc phy-connection-types from rgmii-id to rgmii-rxid
*/
if ((REVID_MAJOR(immr->sysconf.spridr) == 2) &&
(REVID_MINOR(immr->sysconf.spridr) == 1)) {
if (board_handle_erratum2()) {
int nodeoffset;
const char *prop;
int path;
......
......@@ -23,8 +23,8 @@
#include <common.h>
#include <mpc83xx.h>
#include <ioports.h>
#ifdef CONFIG_USB_EHCI_FSL
#include <asm/io.h>
#ifdef CONFIG_USB_EHCI_FSL
#include <usb/ehci-fsl.h>
#endif
......@@ -63,149 +63,163 @@ static void config_qe_ioports(void)
*/
void cpu_init_f (volatile immap_t * im)
{
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
/* Clear initial global data */
memset ((void *) gd, 0, sizeof (gd_t));
/* system performance tweaking */
#ifdef CONFIG_SYS_ACR_PIPE_DEP
/* Arbiter pipeline depth */
im->arbiter.acr = (im->arbiter.acr & ~ACR_PIPE_DEP) |
(CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT);
__be32 acr_mask =
#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */
(ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) |
#endif
#ifdef CONFIG_SYS_ACR_RPTCNT
/* Arbiter repeat count */
im->arbiter.acr = (im->arbiter.acr & ~(ACR_RPTCNT)) |
(CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT);
#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */
(ACR_RPTCNT << ACR_RPTCNT_SHIFT) |
#endif
0;
__be32 acr_val =
#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */
(CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) |
#endif
#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */
(CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT) |
#endif
0;
__be32 spcr_mask =
#ifdef CONFIG_SYS_SPCR_OPT /* Optimize transactions between CSB and other dev */
(SPCR_OPT << SPCR_OPT_SHIFT) |
#endif
#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */
(SPCR_TSECEP << SPCR_TSECEP_SHIFT) |
#endif
#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */
(SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) |
#endif
#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */
(SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) |
#endif
0;
__be32 spcr_val =
#ifdef CONFIG_SYS_SPCR_OPT
/* Optimize transactions between CSB and other devices */
im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_OPT) |
(CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT);
(CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT) |
#endif
#ifdef CONFIG_SYS_SPCR_TSECEP
/* all eTSEC's Emergency priority */
im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSECEP) |
(CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT);
#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */
(CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT) |
#endif
#ifdef CONFIG_SYS_SPCR_TSEC1EP
/* TSEC1 Emergency priority */
im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) |
(CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT);
#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */
(CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) |
#endif
#ifdef CONFIG_SYS_SPCR_TSEC2EP
/* TSEC2 Emergency priority */
im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) |
(CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT);
#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */
(CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_ENCCM
/* Encryption clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_ENCCM) |
(CONFIG_SYS_SCCR_ENCCM << SCCR_ENCCM_SHIFT);
0;
__be32 sccr_mask =
#ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */
(SCCR_ENCCM << SCCR_ENCCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_PCICM
/* PCI & DMA clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_PCICM) |
(CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT);
#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
(SCCR_PCICM << SCCR_PCICM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSECCM
/* all TSEC's clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSECCM) |
(CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT);
#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
(SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC1CM
/* TSEC1 clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) |
(CONFIG_SYS_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT);
#ifdef CONFIG_SYS_SCCR_TSEC1CM /* TSEC1 clock mode */
(SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC2CM
/* TSEC2 clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) |
(CONFIG_SYS_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT);
#ifdef CONFIG_SYS_SCCR_TSEC2CM /* TSEC2 clock mode */
(SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC1ON
/* TSEC1 clock switch */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1ON) |
(CONFIG_SYS_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT);
#ifdef CONFIG_SYS_SCCR_TSEC1ON /* TSEC1 clock switch */
(SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC2ON
/* TSEC2 clock switch */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2ON) |
(CONFIG_SYS_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT);
#ifdef CONFIG_SYS_SCCR_TSEC2ON /* TSEC2 clock switch */
(SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_USBMPHCM
/* USB MPH clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_USBMPHCM) |
(CONFIG_SYS_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT);
#ifdef CONFIG_SYS_SCCR_USBMPHCM /* USB MPH clock mode */
(SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_USBDRCM
/* USB DR clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_USBDRCM) |
(CONFIG_SYS_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT);
#ifdef CONFIG_SYS_SCCR_USBDRCM /* USB DR clock mode */
(SCCR_USBDRCM << SCCR_USBDRCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_SATACM
/* SATA controller clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_SATACM) |
(CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT);
#ifdef CONFIG_SYS_SCCR_SATACM /* SATA controller clock mode */
(SCCR_SATACM << SCCR_SATACM_SHIFT) |
#endif
0;
__be32 sccr_val =
#ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */
(CONFIG_SYS_SCCR_ENCCM << SCCR_ENCCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
(CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
(CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC1CM /* TSEC1 clock mode */
(CONFIG_SYS_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC2CM /* TSEC2 clock mode */
(CONFIG_SYS_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC1ON /* TSEC1 clock switch */
(CONFIG_SYS_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_TSEC2ON /* TSEC2 clock switch */
(CONFIG_SYS_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_USBMPHCM /* USB MPH clock mode */
(CONFIG_SYS_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_USBDRCM /* USB DR clock mode */
(CONFIG_SYS_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT) |
#endif
#ifdef CONFIG_SYS_SCCR_SATACM /* SATA controller clock mode */
(CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT) |
#endif
0;
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
/* Clear initial global data */
memset ((void *) gd, 0, sizeof (gd_t));
/* system performance tweaking */
clrsetbits_be32(&im->arbiter.acr, acr_mask, acr_val);
clrsetbits_be32(&im->sysconf.spcr, spcr_mask, spcr_val);
clrsetbits_be32(&im->clk.sccr, sccr_mask, sccr_val);
/* RSR - Reset Status Register - clear all status (4.6.1.3) */
gd->reset_status = im->reset.rsr;
im->reset.rsr = ~(RSR_RES);
gd->reset_status = __raw_readl(&im->reset.rsr);
__raw_writel(~(RSR_RES), &im->reset.rsr);
/* AER - Arbiter Event Register - store status */
gd->arbiter_event_attributes = im->arbiter.aeatr;
gd->arbiter_event_address = im->arbiter.aeadr;
gd->arbiter_event_attributes = __raw_readl(&im->arbiter.aeatr);
gd->arbiter_event_address = __raw_readl(&im->arbiter.aeadr);
/*
* RMR - Reset Mode Register
* contains checkstop reset enable (4.6.1.4)
*/
im->reset.rmr = (RMR_CSRE & (1<<RMR_CSRE_SHIFT));
/* LCRR - Clock Ratio Register (10.3.1.16) */
im->lbus.lcrr = CONFIG_SYS_LCRR;
__raw_writel(RMR_CSRE & (1<<RMR_CSRE_SHIFT), &im->reset.rmr);
/* Enable Time Base & Decrimenter ( so we will have udelay() )*/
im->sysconf.spcr |= SPCR_TBEN;
/* Enable Time Base & Decrementer ( so we will have udelay() )*/
setbits_be32(&im->sysconf.spcr, SPCR_TBEN);
/* System General Purpose Register */
#ifdef CONFIG_SYS_SICRH
#if defined(CONFIG_MPC834x) || defined(CONFIG_MPC8313)
/* regarding to MPC34x manual rev.1 bits 28..29 must be preserved */
im->sysconf.sicrh = (im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH;
__raw_writel((im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH,
&im->sysconf.sicrh);
#else
im->sysconf.sicrh = CONFIG_SYS_SICRH;
__raw_writel(CONFIG_SYS_SICRH, &im->sysconf.sicrh);
#endif
#endif
#ifdef CONFIG_SYS_SICRL
im->sysconf.sicrl = CONFIG_SYS_SICRL;
__raw_writel(CONFIG_SYS_SICRL, &im->sysconf.sicrl);
#endif
/* DDR control driver register */
#ifdef CONFIG_SYS_DDRCDR
im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR;
#ifdef CONFIG_SYS_DDRCDR /* DDR control driver register */
__raw_writel(CONFIG_SYS_DDRCDR, &im->sysconf.ddrcdr);
#endif
/* Output buffer impedance register */
#ifdef CONFIG_SYS_OBIR
im->sysconf.obir = CONFIG_SYS_OBIR;
#ifdef CONFIG_SYS_OBIR /* Output buffer impedance register */
__raw_writel(CONFIG_SYS_OBIR, &im->sysconf.obir);
#endif
#ifdef CONFIG_QE
......@@ -308,7 +322,7 @@ void cpu_init_f (volatile immap_t * im)
/* Wait for clock to stabilize */
do {
temp = in_be32(&ehci->control);
temp = __raw_readl(&ehci->control);
udelay(1000);
} while (!(temp & PHY_CLK_VALID));
#endif
......@@ -317,8 +331,41 @@ void cpu_init_f (volatile immap_t * im)
int cpu_init_r (void)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
#ifdef CONFIG_QE
uint qe_base = CONFIG_SYS_IMMR + 0x00100000; /* QE immr base */
#endif
__be32 lcrr_mask =
#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */
LCRR_DBYP |
#endif
#ifdef CONFIG_SYS_LCRR_EADC /* external address delay */
LCRR_EADC |
#endif
#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */
LCRR_CLKDIV |
#endif
0;
__be32 lcrr_val =
#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */
CONFIG_SYS_LCRR_DBYP |
#endif
#ifdef CONFIG_SYS_LCRR_EADC
CONFIG_SYS_LCRR_EADC |
#endif
#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */
CONFIG_SYS_LCRR_CLKDIV |
#endif
0;
/* LCRR - Clock Ratio Register (10.3.1.16)
* write, read, and isync per MPC8379ERM rev.1 CLKDEV field description
*/
clrsetbits_be32(&im->lbus.lcrr, lcrr_mask, lcrr_val);
__raw_readl(&im->lbus.lcrr);
isync();
#ifdef CONFIG_QE
qe_init(qe_base);
qe_reset();
#endif
......
......@@ -25,6 +25,7 @@
#include "common.h"
#include "qe.h"
#include "asm/immap_qe.h"
/* Fast or Giga ethernet
*/
......
......@@ -23,6 +23,9 @@
#ifndef __UEC_H__
#define __UEC_H__
#include "qe.h"
#include "uccf.h"
#define MAX_TX_THREADS 8
#define MAX_RX_THREADS 8
#define MAX_TX_QUEUES 8
......@@ -670,6 +673,7 @@ typedef enum enet_interface {
ENET_1000_RGMII,
ENET_1000_RGMII_ID,
ENET_1000_RGMII_RXID,
ENET_1000_RGMII_TXID,
ENET_1000_TBI,
ENET_1000_RTBI,
ENET_1000_SGMII
......
......@@ -429,12 +429,23 @@ static int marvell_init(struct uec_mii_info *mii_info)
{
struct eth_device *edev = mii_info->dev;
uec_private_t *uec = edev->priv;
enum enet_interface iface = uec->uec_info->enet_interface;
if (uec->uec_info->enet_interface == ENET_1000_RGMII_ID) {
if (iface == ENET_1000_RGMII_ID ||
iface == ENET_1000_RGMII_RXID ||
iface == ENET_1000_RGMII_TXID) {
int temp;
temp = phy_read(mii_info, MII_M1111_PHY_EXT_CR);
temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY);
if (iface == ENET_1000_RGMII_ID) {
temp |= MII_M1111_RX_DELAY | MII_M1111_TX_DELAY;
} else if (iface == ENET_1000_RGMII_RXID) {
temp &= ~MII_M1111_TX_DELAY;
temp |= MII_M1111_RX_DELAY;
} else if (iface == ENET_1000_RGMII_TXID) {
temp &= ~MII_M1111_RX_DELAY;
temp |= MII_M1111_TX_DELAY;
}
phy_write(mii_info, MII_M1111_PHY_EXT_CR, temp);
temp = phy_read(mii_info, MII_M1111_PHY_EXT_SR);
......
......@@ -216,7 +216,8 @@
/*
* Local Bus LCRR and LBCR regs
*/
#define CONFIG_SYS_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4
#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR ( 0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
......
......@@ -182,7 +182,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00040000
/*
......
......@@ -170,7 +170,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
......
......@@ -159,7 +159,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
......
......@@ -206,7 +206,8 @@
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
......
......@@ -317,7 +317,8 @@ boards, we say we have two, but don't display a message if we find only one. */
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
......
......@@ -185,7 +185,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000