Commit 3d248d37 authored by Ben Gardiner's avatar Ben Gardiner Committed by Wolfgang Denk
Browse files

da850evm: basic MII EMAC support



The current da850evm support in u-boot/master omits any use of
the davinci EMAC. This patch adds basic support for the EMAC using
the MII PHY found on the baseboard of the EVM. The MAC address is
read from the environment variable 'ethadd'. Note that this is
different from the da850evm support in the u-boot omapl1 tree
where the MAC address is read from SPI flash.
Signed-off-by: default avatarBen Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarSandeep Paulraj <s-paulraj@ti.com>
parent 771d028a
......@@ -23,8 +23,11 @@
#include <common.h>
#include <i2c.h>
#include <net.h>
#include <netdev.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emif_defs.h>
#include <asm/arch/emac_defs.h>
#include <asm/io.h>
#include "../common/misc.h"
#include "common.h"
......@@ -49,6 +52,28 @@ static const struct pinmux_config uart_pins[] = {
{ pinmux(4), 2, 5 }
};
#ifdef CONFIG_DRIVER_TI_EMAC
static const struct pinmux_config emac_pins[] = {
{ pinmux(2), 8, 1 },
{ pinmux(2), 8, 2 },
{ pinmux(2), 8, 3 },
{ pinmux(2), 8, 4 },
{ pinmux(2), 8, 5 },
{ pinmux(2), 8, 6 },
{ pinmux(2), 8, 7 },
{ pinmux(3), 8, 0 },
{ pinmux(3), 8, 1 },
{ pinmux(3), 8, 2 },
{ pinmux(3), 8, 3 },
{ pinmux(3), 8, 4 },
{ pinmux(3), 8, 5 },
{ pinmux(3), 8, 6 },
{ pinmux(3), 8, 7 },
{ pinmux(4), 8, 0 },
{ pinmux(4), 8, 1 }
};
#endif /* CONFIG_DRIVER_TI_EMAC */
/* I2C pin muxer settings */
static const struct pinmux_config i2c_pins[] = {
{ pinmux(4), 2, 2 },
......@@ -142,6 +167,14 @@ int board_init(void)
if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
return 1;
#ifdef CONFIG_DRIVER_TI_EMAC
if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0)
return 1;
/* set cfgchip3 to select MII */
writel(readl(&davinci_syscfg_regs->cfgchip3) & ~(1 << 8),
&davinci_syscfg_regs->cfgchip3);
#endif /* CONFIG_DRIVER_TI_EMAC */
/* enable the console UART */
writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
DAVINCI_UART_PWREMU_MGMT_UTRST),
......@@ -149,3 +182,19 @@ int board_init(void)
return 0;
}
#ifdef CONFIG_DRIVER_TI_EMAC
/*
* Initializes on-board ethernet controllers.
*/
int board_eth_init(bd_t *bis)
{
if (!davinci_emac_initialize()) {
printf("Error: Ethernet init failed!\n");
return -1;
}
return 0;
}
#endif /* CONFIG_DRIVER_TI_EMAC */
......@@ -26,6 +26,7 @@
/*
* Board
*/
#define CONFIG_DRIVER_TI_EMAC
/*
* SoC Configuration
......@@ -101,6 +102,20 @@
#define DEF_BOOTM ""
#endif
/*
* Network & Ethernet Configuration
*/
#ifdef CONFIG_DRIVER_TI_EMAC
#define CONFIG_EMAC_MDIO_PHY_NUM 0
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#define CONFIG_NET_MULTI
#endif
/*
* U-Boot general configuration
*/
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment