Commit 6515032e authored by Hans de Goede's avatar Hans de Goede
Browse files

sunxi: display: Make lcd display clk phase configurable



While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.

This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.

This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.

The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Acked-by: default avatarIan Campbell <ijc@hellion.org.uk>
parent b56f6e2b
......@@ -249,9 +249,7 @@ struct sunxi_tve_reg {
#define SUNXI_LCDC_TCON0_TIMING_V_TOTAL(n) (((n) * 2) << 16)
#define SUNXI_LCDC_TCON0_LVDS_INTF_BITWIDTH(n) ((n) << 26)
#define SUNXI_LCDC_TCON0_LVDS_INTF_ENABLE (1 << 31)
#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE0 (0 << 28)
#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE60 (1 << 28)
#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE120 (2 << 28)
#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE(x) ((x) << 28)
#define SUNXI_LCDC_TCON1_CTRL_CLK_DELAY(n) (((n) & 0x1f) << 4)
#define SUNXI_LCDC_TCON1_CTRL_ENABLE (1 << 31)
#define SUNXI_LCDC_TCON1_TIMING_H_BP(n) (((n) - 1) << 0)
......
......@@ -338,6 +338,13 @@ config VIDEO_LCD_MODE
This is in drivers/video/videomodes.c: video_get_params() format, e.g.
x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
config VIDEO_LCD_DCLK_PHASE
int "LCD panel display clock phase"
depends on VIDEO
default 1
---help---
Select LCD panel display clock phase shift, range 0-3.
config VIDEO_LCD_POWER
string "LCD panel power enable pin"
depends on VIDEO
......
......@@ -2,6 +2,7 @@ CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
CONFIG_FDTFILE="sun8i-a23-ippo-q8h-v1.2.dtb"
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
......
......@@ -2,6 +2,7 @@ CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
CONFIG_FDTFILE="sun8i-a23-ippo-q8h-v5.dtb"
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
......
......@@ -2,6 +2,7 @@ CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
CONFIG_FDTFILE="sun7i-a20-primo73.dtb"
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:60000,le:60,ri:160,up:13,lo:12,hs:100,vs:10,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH8"
CONFIG_VIDEO_LCD_BL_EN="PH7"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
......
......@@ -587,12 +587,7 @@ static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode)
&lcdc->tcon0_frm_ctrl);
}
#ifdef CONFIG_VIDEO_LCD_IF_PARALLEL
val = SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE0;
#endif
#ifdef CONFIG_VIDEO_LCD_IF_LVDS
val = SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE60;
#endif
val = SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE(CONFIG_VIDEO_LCD_DCLK_PHASE);
if (!(mode->sync & FB_SYNC_HOR_HIGH_ACT))
val |= SUNXI_LCDC_TCON_HSYNC_MASK;
if (!(mode->sync & FB_SYNC_VERT_HIGH_ACT))
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment