Commit 7737c994 authored by Simon Guinot's avatar Simon Guinot Committed by Prafulla Wadaskar
Browse files

net2big_v2: initialize LEDs at startup



This patch allows to configure the net2big_v2 LEDs at startup (through
the GPIO extension bus). The front blue LED is enabled and the SATA rear
LEDs are configured to blink in relation with the SATA activity.
Signed-off-by: default avatarSimon Guinot <simon.guinot@sequanux.org>
parent d5cc3f52
......@@ -28,6 +28,9 @@ endif
LIB = $(obj)lib$(BOARD).o
COBJS := $(BOARD).o ../common/common.o
ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
COBJS += ../common/cpld-gpio-bus.o
endif
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
......
......@@ -30,6 +30,7 @@
#include "net2big_v2.h"
#include "../common/common.h"
#include "../common/cpld-gpio-bus.h"
DECLARE_GLOBAL_DATA_PTR;
......@@ -61,18 +62,18 @@ int board_early_init_f(void)
MPP24_GPIO, /* USB mode select */
MPP26_GPIO, /* USB device vbus */
MPP28_GPIO, /* USB enable host vbus */
MPP29_GPIO, /* GPIO extension ALE */
MPP29_GPIO, /* CPLD GPIO bus ALE */
MPP34_GPIO, /* Rear Push button 0=on 1=off */
MPP35_GPIO, /* Inhibit switch power-off */
MPP36_GPIO, /* SATA HDD1 presence */
MPP37_GPIO, /* SATA HDD2 presence */
MPP40_GPIO, /* eSATA presence */
MPP44_GPIO, /* GPIO extension (data 0) */
MPP45_GPIO, /* GPIO extension (data 1) */
MPP46_GPIO, /* GPIO extension (data 2) */
MPP47_GPIO, /* GPIO extension (addr 0) */
MPP48_GPIO, /* GPIO extension (addr 1) */
MPP49_GPIO, /* GPIO extension (addr 2) */
MPP44_GPIO, /* CPLD GPIO bus (data 0) */
MPP45_GPIO, /* CPLD GPIO bus (data 1) */
MPP46_GPIO, /* CPLD GPIO bus (data 2) */
MPP47_GPIO, /* CPLD GPIO bus (addr 0) */
MPP48_GPIO, /* CPLD GPIO bus (addr 1) */
MPP49_GPIO, /* CPLD GPIO bus (addr 2) */
0
};
......@@ -143,6 +144,89 @@ err:
static void init_fan(void) {}
#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
/*
* CPLD GPIO bus:
*
* - address register : bit [0-2] -> GPIO [47-49]
* - data register : bit [0-2] -> GPIO [44-46]
* - enable register : GPIO 29
*/
static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
static struct cpld_gpio_bus cpld_gpio_bus = {
.addr = cpld_gpio_bus_addr,
.num_addr = ARRAY_SIZE(cpld_gpio_bus_addr),
.data = cpld_gpio_bus_data,
.num_data = ARRAY_SIZE(cpld_gpio_bus_data),
.enable = 29,
};
/*
* LEDs configuration:
*
* The LEDs are controlled by a CPLD and can be configured through
* the CPLD GPIO bus.
*
* Address register selection:
*
* addr | register
* ----------------------------
* 0 | front LED
* 1 | front LED brightness
* 2 | SATA LED brightness
* 3 | SATA0 LED
* 4 | SATA1 LED
* 5 | SATA2 LED
* 6 | SATA3 LED
* 7 | SATA4 LED
*
* Data register configuration:
*
* data | LED brightness
* -------------------------------------------------
* 0 | min (off)
* - | -
* 7 | max
*
* data | front LED mode
* -------------------------------------------------
* 0 | fix off
* 1 | fix blue on
* 2 | fix red on
* 3 | blink blue on=1 sec and blue off=1 sec
* 4 | blink red on=1 sec and red off=1 sec
* 5 | blink blue on=2.5 sec and red on=0.5 sec
* 6 | blink blue on=1 sec and red on=1 sec
* 7 | blink blue on=0.5 sec and blue off=2.5 sec
*
* data | SATA LED mode
* -------------------------------------------------
* 0 | fix off
* 1 | SATA activity blink
* 2 | fix red on
* 3 | blink blue on=1 sec and blue off=1 sec
* 4 | blink red on=1 sec and red off=1 sec
* 5 | blink blue on=2.5 sec and red on=0.5 sec
* 6 | blink blue on=1 sec and red on=1 sec
* 7 | fix blue on
*/
static void init_leds(void)
{
/* Enable the front blue LED */
cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
/* Configure SATA LEDs to blink in relation with the SATA activity */
cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
}
#else
static void init_leds(void) {}
#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
int misc_init_r(void)
{
init_fan();
......@@ -153,6 +237,8 @@ int misc_init_r(void)
eth_setenv_enetaddr("ethaddr", mac);
}
#endif
init_leds();
return 0;
}
#endif /* CONFIG_MISC_INIT_R */
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment