Commit 9d909604 authored by Stefan Roese's avatar Stefan Roese
Browse files

ppc4xx: Update Sequoia NAND booting support with ECC


Signed-off-by: default avatarStefan Roese <sr@denx.de>
parent cf959c7d
......@@ -379,7 +379,11 @@ void denali_core_search_data_eye(unsigned long memory_size)
long int initdram (int board_type)
{
#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
#if !defined(CONFIG_NAND_SPL)
ulong speed = get_bus_freq(0);
#else
ulong speed = 133333333; /* 133MHz is on the safe side */
#endif
mtsdram(DDR0_02, 0x00000000);
......
......@@ -166,12 +166,19 @@
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
#define CFG_NAND_PAGE_SIZE (512) /* NAND chip page size */
#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
#define CFG_NAND_PAGE_COUNT (32) /* NAND chip page count */
#define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */
#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
#define CFG_NAND_ECCSIZE 256
#define CFG_NAND_ECCBYTES 3
#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
#define CFG_NAND_OOBSIZE 16
#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CFG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
......
......@@ -30,7 +30,7 @@ AFLAGS += -DCONFIG_NAND_SPL
CFLAGS += -DCONFIG_NAND_SPL
SOBJS = start.o init.o resetvec.o
COBJS = nand_boot.o ndfc.o sdram.o speed.o
COBJS = nand_boot.o nand_ecc.o ndfc.o sdram.o
SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
......@@ -69,10 +69,6 @@ $(obj)start.S:
@rm -f $(obj)start.S
ln -s $(SRCTREE)/cpu/ppc4xx/start.S $(obj)start.S
$(obj)speed.c:
@rm -f $(obj)speed.c
ln -s $(SRCTREE)/cpu/ppc4xx/speed.c $(obj)speed.c
# from board directory
$(obj)init.S:
@rm -f $(obj)init.S
......@@ -89,6 +85,11 @@ $(obj)nand_boot.c:
@rm -f $(obj)nand_boot.c
ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c
# from drivers/nand directory
$(obj)nand_ecc.c:
@rm -f $(obj)nand_ecc.c
ln -s $(SRCTREE)/drivers/nand/nand_ecc.c $(obj)nand_ecc.c
#########################################################################
$(obj)%.o: $(obj)%.S
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment