Commit a55d9fee authored by Masahiro Yamada's avatar Masahiro Yamada
Browse files

ARM: uniphier: add eMMC boot support



Export device nodes needed for eMMC boot (eMMC node, pinctrl, and
clock) to the SPL DTB.  CONFIG_SUPPORT_EMMC_BOOT is also necessary
to use "mmc partconf" command.
Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
parent c7f94eec
......@@ -95,6 +95,14 @@
u-boot,dm-pre-reloc;
};
&mio {
u-boot,dm-pre-reloc;
};
&emmc {
u-boot,dm-pre-reloc;
};
&pinctrl {
u-boot,dm-pre-reloc;
};
......@@ -102,3 +110,7 @@
&pinctrl_uart0 {
u-boot,dm-pre-reloc;
};
&pinctrl_emmc {
u-boot,dm-pre-reloc;
};
......@@ -75,6 +75,14 @@
u-boot,dm-pre-reloc;
};
&mio {
u-boot,dm-pre-reloc;
};
&emmc {
u-boot,dm-pre-reloc;
};
&pinctrl {
u-boot,dm-pre-reloc;
};
......@@ -82,3 +90,7 @@
&pinctrl_uart2 {
u-boot,dm-pre-reloc;
};
&pinctrl_emmc {
u-boot,dm-pre-reloc;
};
......@@ -60,6 +60,14 @@
u-boot,dm-pre-reloc;
};
&mio {
u-boot,dm-pre-reloc;
};
&emmc {
u-boot,dm-pre-reloc;
};
&pinctrl {
u-boot,dm-pre-reloc;
};
......@@ -67,3 +75,7 @@
&pinctrl_uart2 {
u-boot,dm-pre-reloc;
};
&pinctrl_emmc {
u-boot,dm-pre-reloc;
};
......@@ -5,6 +5,7 @@
*/
#include <common.h>
#include <mmc.h>
#include <spl.h>
#include "../sbc/sbc-regs.h"
......@@ -52,3 +53,27 @@ u32 spl_boot_device(void)
return ret == BOOT_DEVICE_USB ? BOOT_DEVICE_NOR : ret;
}
u32 spl_boot_mode(void)
{
struct mmc *mmc;
/*
* work around a bug in the Boot ROM of PH1-sLD3, LD4, Pro4, and sLD8:
*
* The boot ROM in these SoCs breaks the PARTITION_CONFIG [179] of
* Extended CSD register; when switching to the Boot Partition 1, the
* Boot ROM should issue the SWITCH command (CMD6) with Set Bits for
* the Access Bits, but in fact it uses Write Byte for the Access Bits.
* As a result, the BOOT_PARTITION_ENABLE field of the PARTITION_CONFIG
* is lost. This bug was fixed for PH1-Pro5 and later SoCs.
*
* Fixup mmc->part_config here because it is used to determine the
* partition which the U-Boot image is read from.
*/
mmc = find_mmc_device(0);
mmc->part_config &= ~EXT_CSD_BOOT_PART_NUM(PART_ACCESS_MASK);
mmc->part_config |= EXT_CSD_BOOT_PARTITION_ENABLE;
return MMCSD_MODE_EMMCBOOT;
}
......@@ -148,6 +148,7 @@
/* SD/MMC */
#define CONFIG_CMD_MMC
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_GENERIC_MMC
/* memtest works on */
......@@ -263,6 +264,7 @@
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */
#define CONFIG_SPL_LIBGENERIC_SUPPORT
......@@ -270,6 +272,7 @@
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x80
#define CONFIG_SPL_MAX_FOOTPRINT 0x10000
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment