Commit a69e037e authored by Masahiro Yamada's avatar Masahiro Yamada
Browse files

ARM: UniPhier: move DDR related configuration to Kconfig


Signed-off-by: default avatarMasahiro Yamada <yamada.m@jp.panasonic.com>
parent b603c681
......@@ -32,4 +32,27 @@ config CMD_PINMON
The boot mode pins are latched when the system reset is deasserted
and determine which device the system should load a boot image from.
config DRAM_INIT
bool
default SPL_BUILD
choice
prompt "DDR3 Frequency select"
depends on DRAM_INIT
config DDR_FREQ_1600
bool "DDR3 1600"
depends on MACH_PH1_PRO4 || MACH_PH1_LD4
config DDR_FREQ_1333
bool "DDR3 1333"
depends on MACH_PH1_LD4 || MACH_PH1_SLD8
endchoice
config DDR_FREQ
int
default 1333 if DDR_FREQ_1333
default 1600 if DDR_FREQ_1600
endmenu
......@@ -16,7 +16,7 @@ int dram_init(void)
DECLARE_GLOBAL_DATA_PTR;
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
#ifdef CONFIG_DRAM_INIT
led_write(B, 4, , );
{
......
......@@ -7,5 +7,4 @@ obj-y += platdevice.o
obj-y += boot-mode.o
obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \
sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o
obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
umc_init.o
obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o
......@@ -149,10 +149,6 @@ int umc_init(void)
CONFIG_SDRAM1_SIZE / 0x08000000);
}
#if CONFIG_DDR_FREQ != 1333 && CONFIG_DDR_FREQ != 1600
#error Unsupported DDR Frequency.
#endif
#if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \
(CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \
CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1
......
......@@ -7,5 +7,4 @@ obj-y += platdevice.o
obj-y += boot-mode.o
obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o sbc_init.o \
sg_init.o pll_init.o clkrst_init.o pinctrl.o
obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
umc_init.o
obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o
......@@ -122,10 +122,6 @@ int umc_init(void)
CONFIG_SDRAM1_SIZE / 0x08000000);
}
#if CONFIG_DDR_FREQ != 1600
#error Unsupported DDR frequency.
#endif
#if ((CONFIG_SDRAM0_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH0 == 2) || \
(CONFIG_SDRAM0_SIZE == 0x10000000 && CONFIG_DDR_NUM_CH0 == 1)) && \
((CONFIG_SDRAM1_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH1 == 2) || \
......
......@@ -7,5 +7,4 @@ obj-y += platdevice.o
obj-y += boot-mode.o
obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \
sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o
obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
umc_init.o
obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o
......@@ -129,10 +129,6 @@ int umc_init(void)
CONFIG_SDRAM1_SIZE / 0x08000000);
}
#if CONFIG_DDR_FREQ != 1333
#error Unsupported DDR frequency.
#endif
#if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \
(CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \
CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1
......
......@@ -37,8 +37,6 @@
#define CONFIG_DDR_NUM_CH0 1
#define CONFIG_DDR_NUM_CH1 1
#define CONFIG_DDR_FREQ 1600
/*
* Memory Size & Mapping
*/
......
......@@ -37,8 +37,6 @@
#define CONFIG_DDR_NUM_CH0 2
#define CONFIG_DDR_NUM_CH1 2
#define CONFIG_DDR_FREQ 1600
#define CONFIG_UNIPHIER_SMP
/*
......
......@@ -37,8 +37,6 @@
#define CONFIG_DDR_NUM_CH0 1
#define CONFIG_DDR_NUM_CH1 1
#define CONFIG_DDR_FREQ 1333
/* #define CONFIG_DDR_STANDARD */
/*
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment