Commit a931b137 authored by Bo Shen's avatar Bo Shen Committed by Andreas Bießmann
Browse files

ARM: atmel: sama5d3xek: add nor flash init function



Add NOR flash hardware init function, including SMC and PIO
configuration.
Signed-off-by: default avatarBo Shen <voice.shen@atmel.com>
Reviewed-by: default avatarAndreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: default avatarAndreas Bießmann <andreas.devel@googlemail.com>
parent 14b3b44e
......@@ -67,6 +67,61 @@ void sama5d3xek_nand_hw_init(void)
}
#endif
#ifndef CONFIG_SYS_NO_FLASH
static void sama5d3xek_nor_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
at91_periph_clk_enable(ATMEL_ID_SMC);
/* Configure SMC CS0 for NOR flash */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[0].setup);
writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(11) |
AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(11),
&smc->cs[0].pulse);
writel(AT91_SMC_CYCLE_NWE(11) | AT91_SMC_CYCLE_NRD(14),
&smc->cs[0].cycle);
writel(AT91_SMC_TIMINGS_TCLR(0) | AT91_SMC_TIMINGS_TADL(0) |
AT91_SMC_TIMINGS_TAR(0) | AT91_SMC_TIMINGS_TRR(0) |
AT91_SMC_TIMINGS_TWB(0) | AT91_SMC_TIMINGS_RBNSEL(0)|
AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_16 |
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[0].mode);
/* Address pin (A1 ~ A23) configuration */
at91_set_a_periph(AT91_PIO_PORTE, 1, 0);
at91_set_a_periph(AT91_PIO_PORTE, 2, 0);
at91_set_a_periph(AT91_PIO_PORTE, 3, 0);
at91_set_a_periph(AT91_PIO_PORTE, 4, 0);
at91_set_a_periph(AT91_PIO_PORTE, 5, 0);
at91_set_a_periph(AT91_PIO_PORTE, 6, 0);
at91_set_a_periph(AT91_PIO_PORTE, 7, 0);
at91_set_a_periph(AT91_PIO_PORTE, 8, 0);
at91_set_a_periph(AT91_PIO_PORTE, 9, 0);
at91_set_a_periph(AT91_PIO_PORTE, 10, 0);
at91_set_a_periph(AT91_PIO_PORTE, 11, 0);
at91_set_a_periph(AT91_PIO_PORTE, 12, 0);
at91_set_a_periph(AT91_PIO_PORTE, 13, 0);
at91_set_a_periph(AT91_PIO_PORTE, 14, 0);
at91_set_a_periph(AT91_PIO_PORTE, 15, 0);
at91_set_a_periph(AT91_PIO_PORTE, 16, 0);
at91_set_a_periph(AT91_PIO_PORTE, 17, 0);
at91_set_a_periph(AT91_PIO_PORTE, 18, 0);
at91_set_a_periph(AT91_PIO_PORTE, 19, 0);
at91_set_a_periph(AT91_PIO_PORTE, 20, 0);
at91_set_a_periph(AT91_PIO_PORTE, 21, 0);
at91_set_a_periph(AT91_PIO_PORTE, 22, 0);
at91_set_a_periph(AT91_PIO_PORTE, 23, 0);
/* CS0 pin configuration */
at91_set_a_periph(AT91_PIO_PORTE, 26, 0);
}
#endif
#ifdef CONFIG_CMD_USB
static void sama5d3xek_usb_hw_init(void)
{
......@@ -181,6 +236,9 @@ int board_init(void)
#ifdef CONFIG_NAND_ATMEL
sama5d3xek_nand_hw_init();
#endif
#ifndef CONFIG_SYS_NO_FLASH
sama5d3xek_nor_hw_init();
#endif
#ifdef CONFIG_CMD_USB
sama5d3xek_usb_hw_init();
#endif
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment