Commit bfc325ed authored by Andreas Bießmann's avatar Andreas Bießmann Committed by Albert ARIBAUD
Browse files

arm:at91-boards: remove console_init_f where unnecessary



A lot of at91 boards have the console_init_f in board_init. This is useless
cause it was called before by generic code in lib/board.c.
Signed-off-by: default avatarAndreas Bießmann <andreas.devel@googlemail.com>
cc: Jens Scharsig <esw@bus-elektronik.de>
cc: Stelian Pop <stelian@popies.net>
cc: Sedji Gaouaou<sedji.gaouaou@atmel.com>
cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
cc: Eric Benard <eric@eukrea.com>
Tested-by: voice.shen@atmel.com
Tested-by: voice.shen@atmel.com
Acked-by: default avatarJens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: default avatarJens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
parent 82c4c645
......@@ -59,8 +59,6 @@ DECLARE_GLOBAL_DATA_PTR;
int board_init(void)
{
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
/* Enable Ctrlc */
console_init_f();
/* Correct IRDA resistor problem / Set PA23_TXD in Output */
writel(ATMEL_PMX_AA_TXD2, &pio->pioa.oer);
......
......@@ -244,9 +244,6 @@ int board_init(void)
writel(pin, &pio->piod.odr);
writel(pin, &pio->piod.owdr);
/* Enable Ctrlc */
console_init_f();
gd->bd->bi_arch_number = MACH_TYPE_VL_MA2SC;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
......
......@@ -242,9 +242,6 @@ void lcd_show_board_info(void)
int board_init(void)
{
/* Enable Ctrlc */
console_init_f();
#ifdef CONFIG_AT91SAM9G10EK
/* arch number of AT91SAM9G10EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
......
......@@ -258,9 +258,6 @@ int board_early_init_f(void)
int board_init(void)
{
/* Enable Ctrlc */
console_init_f();
/* arch number of AT91SAM9M10G45EK-Board */
#ifdef CONFIG_AT91SAM9M10G45EK
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;
......
......@@ -192,9 +192,6 @@ int board_early_init_f(void)
int board_init(void)
{
/* Enable Ctrlc */
console_init_f();
/* arch number of AT91SAM9RLEK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK;
/* adress of boot parameters */
......
......@@ -149,9 +149,6 @@ static void sbc35_a9g20_macb_hw_init(void)
int board_init(void)
{
/* Enable Ctrlc */
console_init_f();
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
......
......@@ -83,9 +83,6 @@ static void tny_a9260_nand_hw_init(void)
int board_init(void)
{
/* Enable Ctrlc */
console_init_f();
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
......
......@@ -43,8 +43,6 @@ DECLARE_GLOBAL_DATA_PTR;
int board_init(void)
{
/* Enable Ctrlc */
console_init_f();
/* arch number of CPUAT91-Board */
gd->bd->bi_arch_number = MACH_TYPE_CPUAT91;
/* adress of boot parameters */
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment