Commit c21617fd authored by Haiying Wang's avatar Haiying Wang Committed by Wolfgang Denk
Browse files

Add DDR options setting on MPC8641HPCN board



* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
Signed-off-by: default avatarJames Yang <James.Yang@freescale.com>
Signed-off-by: default avatarHaiying Wang <Haiying.Wang@freescale.com>
parent 4ca06607
......@@ -46,46 +46,120 @@ void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
}
}
typedef struct {
u32 datarate_mhz_low;
u32 datarate_mhz_high;
u32 n_ranks;
u32 clk_adjust;
u32 cpo;
u32 write_data_delay;
} board_specific_parameters_t;
/* XXX: these values need to be checked for all interleaving modes. */
const board_specific_parameters_t board_specific_parameters[2][16] = {
{
/* memory controller 0 */
/* lo| hi| num| clk| cpo|wrdata */
/* mhz| mhz|ranks|adjst| | delay */
{ 0, 333, 4, 7, 7, 3},
{334, 400, 4, 7, 9, 3},
{401, 549, 4, 7, 9, 3},
{550, 650, 4, 7, 10, 4},
{ 0, 333, 3, 7, 7, 3},
{334, 400, 3, 7, 9, 3},
{401, 549, 3, 7, 9, 3},
{550, 650, 3, 7, 10, 4},
{ 0, 333, 2, 7, 7, 3},
{334, 400, 2, 7, 9, 3},
{401, 549, 2, 7, 9, 3},
{550, 650, 2, 7, 10, 4},
{ 0, 333, 1, 7, 7, 3},
{334, 400, 1, 7, 9, 3},
{401, 549, 1, 7, 9, 3},
{550, 650, 1, 7, 10, 4}
},
{
/* memory controller 1 */
/* lo| hi| num| clk| cpo|wrdata */
/* mhz| mhz|ranks|adjst| | delay */
{ 0, 333, 4, 7, 7, 3},
{334, 400, 4, 7, 9, 3},
{401, 549, 4, 7, 9, 3},
{550, 650, 4, 7, 10, 4},
{ 0, 333, 3, 7, 7, 3},
{334, 400, 3, 7, 9, 3},
{401, 549, 3, 7, 9, 3},
{550, 650, 3, 7, 10, 4},
{ 0, 333, 2, 7, 7, 3},
{334, 400, 2, 7, 9, 3},
{401, 549, 2, 7, 9, 3},
{550, 650, 2, 7, 10, 4},
{ 0, 333, 1, 7, 7, 3},
{334, 400, 1, 7, 9, 3},
{401, 549, 1, 7, 9, 3},
{550, 650, 1, 7, 10, 4}
}
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
/*
* Factors to consider for clock adjust:
* - number of chips on bus
* - position of slot
* - DDR1 vs. DDR2?
* - ???
*
* This needs to be determined on a board-by-board basis.
* 0110 3/4 cycle late
* 0111 7/8 cycle late
*/
popts->clk_adjust = 7;
const board_specific_parameters_t *pbsp =
&(board_specific_parameters[ctrl_num][0]);
u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
sizeof(board_specific_parameters[0][0]);
u32 i;
u32 j;
ulong ddr_freq;
/*
* Factors to consider for CPO:
* - frequency
* - ddr1 vs. ddr2
/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
* that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
* there are two dimms in the controller, set odt_rd_cfg to 3 and
* odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
popts->cpo_override = 10;
/*
* Factors to consider for write data delay:
* - number of DIMMs
*
* 1 = 1/4 clock delay
* 2 = 1/2 clock delay
* 3 = 3/4 clock delay
* 4 = 1 clock delay
* 5 = 5/4 clock delay
* 6 = 3/2 clock delay
*/
popts->write_data_delay = 3;
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (i&1) { /* odd CS */
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 0;
} else { /* even CS */
if ((CONFIG_DIMM_SLOTS_PER_CTLR == 2) &&
(pdimm[i/2].n_ranks != 0)) {
popts->cs_local_opts[i].odt_rd_cfg = 3;
popts->cs_local_opts[i].odt_wr_cfg = 3;
} else {
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 4;
}
}
}
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
/* Get clk_adjust, cpo, write_data_delay, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
popts->half_strength_driver_enable = 0;
ddr_freq = fsl_ddr_get_mem_data_rate() / 1000000;
for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
if (pdimm[j].n_ranks > 0) {
for (i = 0; i < num_params; i++) {
if (ddr_freq >= pbsp->datarate_mhz_low &&
ddr_freq <= pbsp->datarate_mhz_high &&
pdimm[j].n_ranks == pbsp->n_ranks) {
popts->clk_adjust = pbsp->clk_adjust;
popts->cpo_override = pbsp->cpo;
popts->write_data_delay =
pbsp->write_data_delay;
break;
}
pbsp++;
}
}
}
}
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment