Commit d1c1ba85 authored by Stefan Roese's avatar Stefan Roese

ppc4xx: acadia: Add fdt support and fix section overlap problem

This patch adds fdt (flattened device tree) support to the AMCC
Acadia eval board. This increases the image size and it doesn't
fit anymore into 256kByte. Since we didn't want to remove features
from the configuration, we decided to increase the U-Boot image size
(add one flash sector).

Also changed the default environment definition to make it
independent of such changes.
Signed-off-by: default avatarStefan Roese <sr@denx.de>
parent 4adb3023
......@@ -28,7 +28,7 @@
sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
ifndef TEXT_BASE
TEXT_BASE = 0xFFFC0000
TEXT_BASE = 0xFFF80000
endif
ifeq ($(debug),1)
......
......@@ -59,16 +59,16 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CFG_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xfe000000
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_CPLD_BASE 0x80000000
#define CFG_NAND_ADDR 0xd0000000
#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
......@@ -237,6 +237,7 @@
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_NET_MULTI 1
#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/
#define CONFIG_HAS_ETH0 1
#define CONFIG_NETCONSOLE /* include NetConsole support */
......@@ -246,6 +247,9 @@
#undef CONFIG_BOOTARGS
#define xstr(s) str(s)
#define str(s) #s
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=acadia\0" \
......@@ -268,8 +272,9 @@
"ramdisk_addr=fff20000\0" \
"initrd_high=30000000\0" \
"load=tftp 200000 acadia/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b ${fileaddr} fffc0000 ${filesize};" \
"update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
"era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
"cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
"setenv filesize;saveenv\0" \
"upd=run load update\0" \
"nload=tftp 200000 acadia/u-boot-nand.bin\0" \
......@@ -501,4 +506,8 @@
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#endif /* __CONFIG_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment