Commit d4629c8c authored by stroese's avatar stroese
Browse files

CPCI405AB (special version of esd CPCI405) board added.

parent 46578cc0
......@@ -28,5 +28,9 @@
ifeq ($(BOARD_REVISION),CPCI4052)
TEXT_BASE = 0xFFFC0000
else
ifeq ($(BOARD_REVISION),CPCI405AB)
TEXT_BASE = 0xFFFC0000
else
TEXT_BASE = 0xFFFD0000
endif
endif
......@@ -37,7 +37,11 @@
const unsigned char fpgadata[] =
{
#ifdef CONFIG_CPCI405_VER2
# include "fpgadata_cpci4052.c"
# ifdef CONFIG_CPCI405AB
# include "fpgadata_cpci405ab.c"
# else
# include "fpgadata_cpci4052.c"
# endif
#else
# include "fpgadata_cpci405.c"
#endif
......@@ -74,10 +78,10 @@ int board_pre_init (void)
/*
* First pull fpga-prg pin low, to disable fpga logic (on version 2 board)
*/
out32(IBM405GP_GPIO0_ODR, 0x00000000); /* no open drain pins */
out32(IBM405GP_GPIO0_TCR, CFG_FPGA_PRG); /* setup for output */
out32(IBM405GP_GPIO0_OR, CFG_FPGA_PRG); /* set output pins to high */
out32(IBM405GP_GPIO0_OR, 0); /* pull prg low */
out32(GPIO0_ODR, 0x00000000); /* no open drain pins */
out32(GPIO0_TCR, CFG_FPGA_PRG); /* setup for output */
out32(GPIO0_OR, CFG_FPGA_PRG); /* set output pins to high */
out32(GPIO0_OR, 0); /* pull prg low */
/*
* Boot onboard FPGA
......@@ -192,10 +196,10 @@ int cpci405_version(void)
*/
cntrl0Reg = mfdcr(cntrl0);
mtdcr(cntrl0, cntrl0Reg | 0x03000000);
out32(IBM405GP_GPIO0_ODR, in32(IBM405GP_GPIO0_ODR) & ~0x00180000);
out32(IBM405GP_GPIO0_TCR, in32(IBM405GP_GPIO0_TCR) & ~0x00180000);
out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x00180000);
out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x00180000);
udelay(1000); /* wait some time before reading input */
value = in32(IBM405GP_GPIO0_IR) & 0x00180000; /* get config bits */
value = in32(GPIO0_IR) & 0x00180000; /* get config bits */
/*
* Restore GPIO settings
......@@ -505,4 +509,44 @@ void ide_set_reset(int on)
#endif /* CONFIG_IDE_RESET */
#endif /* CONFIG_CPCI405_VER2 */
#if 0 /* test-only */
/* ------------------------------------------------------------------------- */
u8 *dhcp_vendorex_prep (u8 * e)
{
char *ptr;
/* DHCP vendor-class-identifier = 60 */
if ((ptr = getenv ("dhcp_vendor-class-identifier"))) {
*e++ = 60;
*e++ = strlen (ptr);
while (*ptr)
*e++ = *ptr++;
}
/* my DHCP_CLIENT_IDENTIFIER = 61 */
if ((ptr = getenv ("dhcp_client_id"))) {
*e++ = 61;
*e++ = strlen (ptr);
while (*ptr)
*e++ = *ptr++;
}
return e;
}
/* ------------------------------------------------------------------------- */
u8 *dhcp_vendorex_proc (u8 * popt)
{
if (*popt == 61)
return (u8 *)-1;
if (*popt == 43) {
printf("|%s|", popt+4); /* test-only */
return (u8 *)-1;
}
return NULL;
}
/* ------------------------------------------------------------------------- */
#endif /* test-only */
......@@ -86,11 +86,11 @@ unsigned long flash_init (void)
/* Re-do sizing to get full correct info */
if (size_b1) {
base_b1 = -size_b1;
if (size_b1 < (1 << 20)) {
/* minimum CS size on PPC405GP is 1MB !!! */
size_b1 = 1 << 20;
}
base_b1 = -size_b1;
mtdcr (ebccfga, pb0cr);
pbcr = mfdcr (ebccfgd);
mtdcr (ebccfga, pb0cr);
......@@ -103,11 +103,11 @@ unsigned long flash_init (void)
}
if (size_b0) {
base_b0 = base_b1 - size_b0;
if (size_b0 < (1 << 20)) {
/* minimum CS size on PPC405GP is 1MB !!! */
size_b0 = 1 << 20;
}
base_b0 = base_b1 - size_b0;
mtdcr (ebccfga, pb1cr);
pbcr = mfdcr (ebccfgd);
mtdcr (ebccfga, pb1cr);
......
This diff is collapsed.
/*
* (C) Copyright 2001-2003
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
#define CONFIG_CPCI405AB 1 /* ...and special AB version */
#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 0
#define CONFIG_PREBOOT \
"crc32 f0207004 ffc 0;" \
"if cmp 0 f0207000 1;" \
"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
"else;echo Old CRC is bad;fi"
#endif
#undef CONFIG_BOOTARGS
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
"bootm ffc00000 ffca0000"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
"bootm ffc00000"
#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
#if 0 /* test-only */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_VENDOREX)
#else
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT)
#endif
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
CFG_CMD_ELF | \
CFG_CMD_DATE | \
CFG_CMD_JFFS2 | \
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#undef CFG_HUSH_PARSER /* use "hush" command parser */
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
#define CFG_ATA_BASE_ADDR 0xF0100000
#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFFC0000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#define CFG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-(CFG_ENV_SIZE+8)) /* Env */
#else /* Use EEPROM for environment variables */
#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars*/
/* total size of a CAT24WC08 is 1024 bytes */
#endif
#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC08) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
/* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (Flash Bank 0) initialization */
#define CFG_EBC_PB0AP 0x92015480
#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
/* Memory Bank 1 (Flash Bank 1) initialization */
#define CFG_EBC_PB1AP 0x92015480
#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
/* Memory Bank 2 (CAN0, 1) initialization */
#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#define CFG_LED_ADDR 0xF0000380
/* Memory Bank 3 (CompactFlash IDE) initialization */
#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
/* Memory Bank 4 (NVRAM/RTC) initialization */
/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 5 (optional Quart) initialization */
#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 6 (FPGA internal) initialization */
#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
#define CFG_FPGA_BASE_ADDR 0xF0400000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
#define CFG_FPGA_MODE 0x00
#define CFG_FPGA_STATUS 0x02
#define CFG_FPGA_TS 0x04
#define CFG_FPGA_TS_LOW 0x06
#define CFG_FPGA_TS_CAP0 0x10
#define CFG_FPGA_TS_CAP0_LOW 0x12
#define CFG_FPGA_TS_CAP1 0x14
#define CFG_FPGA_TS_CAP1_LOW 0x16
#define CFG_FPGA_TS_CAP2 0x18
#define CFG_FPGA_TS_CAP2_LOW 0x1a
#define CFG_FPGA_TS_CAP3 0x1c
#define CFG_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_DUART_RESET 0x0002
#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
#define CFG_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
#define CFG_FPGA_STATUS_DIP0 0x0001
#define CFG_FPGA_STATUS_DIP1 0x0002
#define CFG_FPGA_STATUS_DIP2 0x0004
#define CFG_FPGA_STATUS_FLASH 0x0008
#define CFG_FPGA_STATUS_TS_IRQ 0x1000
#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
#define CFG_FPGA_MAX_SIZE 64*1024 /* 64kByte is enough for XC2S15 */
/* FPGA program pin configuration */
#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment