Commit d52785d7 authored by Wolfgang Denk's avatar Wolfgang Denk
Browse files

Merge branch 'master' of /home/wd/git/u-boot/custodians

parents 5b2da6a3 79f516bc
...@@ -2380,8 +2380,23 @@ MPC837XERDB_config: unconfig ...@@ -2380,8 +2380,23 @@ MPC837XERDB_config: unconfig
MVBLM7_config: unconfig MVBLM7_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx mvblm7 matrix_vision @$(MKCONFIG) $(@:_config=) ppc mpc83xx mvblm7 matrix_vision
sbc8349_config: unconfig sbc8349_config \
@$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349 sbc8349_PCI_33_config \
sbc8349_PCI_66_config: unconfig
@mkdir -p $(obj)include
@if [ "$(findstring _PCI_,$@)" ] ; then \
$(XECHO) -n "... PCI HOST at " ; \
echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
fi ; \
if [ "$(findstring _33_,$@)" ] ; then \
$(XECHO) -n "33MHz... " ; \
echo "#define PCI_33M" >>$(obj)include/config.h ; \
fi ; \
if [ "$(findstring _66_,$@)" ] ; then \
$(XECHO) -n "66MHz... " ; \
echo "#define PCI_66M" >>$(obj)include/config.h ; \
fi ;
@$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349
SIMPC8313_LP_config \ SIMPC8313_LP_config \
SIMPC8313_SP_config: unconfig SIMPC8313_SP_config: unconfig
......
...@@ -91,19 +91,37 @@ safety check before resetting the board upon completion of the reflash. ...@@ -91,19 +91,37 @@ safety check before resetting the board upon completion of the reflash.
PCI: PCI:
==== ====
This board and U-Boot have been tested with PCI built in, on a SBC8349 There are three configuration choices:
and confirmed that the "pci" command showed the intel e1000 that was sbc8349_config
present in the PCI slot. Note that if a 33MHz 32bit card is inserted sbc8349_PCI_33_config
in the slot, then the whole board will clock down to a 33MHz base sbc8349_PCI_66_config
clock instead of the default 66MHz. This will change the baud clocks
and mess up your serial console output. If you want to use a 33MHz PCI The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
card, then you should build a U-Boot with #undef PCI_66M in the will be left empty (M66EN high), and so the board will operate with
include/configs/sbc8349.h and store this to flash prior to powering down a base clock of 66MHz. Note that you need both PCI enabled in u-boot
the board and inserting the 33MHz PCI card. and linux in order to have functional PCI under linux. The only
reason for choosing to not enable PCI would be if you had a very
By default PCI support is disabled to better support very early early (rev 1.0) CPU with possible PCI issues.
revision MPC834x chips with possible PCI issues. Also PCI support is
untested on the sbc8347 variants at this point in time. The second enables PCI support and builds for a 33MHz clock rate. Note
that if a 33MHz 32bit card is inserted in the slot, then the whole board
will clock down to a 33MHz base clock instead of the default 66MHz. This
Paul Gortmaker, 01/2007 will change the baud clocks and mess up your serial console output if you
were previously running at 66MHz. If you want to use a 33MHz PCI card,
then you should build a U-Boot with sbc8349_PCI_33_config and store this
to flash prior to powering down the board and inserting the 33MHz PCI
card.
The third option builds PCI support in, and leaves the clocking at the
default 66MHz. This has been tested with an intel PCI-X e1000 card.
This is also the appropriate choice for people with a recent (non 1.0)
CPU who currently have the PCI slot physically empty, but intend to
possibly add a PCI-X card at a later date.
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x1957 0x0080 Processor 0x20
00.11.00 0x8086 0x1026 Network controller 0x00
=>
...@@ -594,7 +594,7 @@ ...@@ -594,7 +594,7 @@
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8313erdb.dtb #define CONFIG_FDTFILE mpc8313erdb.dtb
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
...@@ -611,7 +611,7 @@ ...@@ -611,7 +611,7 @@
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"console=ttyS0\0" \ "console=ttyS0\0" \
"setbootargs=setenv bootargs " \ "setbootargs=setenv bootargs " \
......
...@@ -566,7 +566,7 @@ ...@@ -566,7 +566,7 @@
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
...@@ -576,7 +576,7 @@ ...@@ -576,7 +576,7 @@
"consoledev=ttyS0\0" \ "consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \ "ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \ "ramdiskfile=ramfs.83xx\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=mpc8315erdb.dtb\0" \ "fdtfile=mpc8315erdb.dtb\0" \
"usb_phy_type=utmi\0" \ "usb_phy_type=utmi\0" \
"" ""
......
...@@ -542,7 +542,7 @@ ...@@ -542,7 +542,7 @@
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc832x_rdb.dtb #define CONFIG_FDTFILE mpc832x_rdb.dtb
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
...@@ -558,7 +558,7 @@ ...@@ -558,7 +558,7 @@
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"ramdiskaddr=1000000\0" \ "ramdiskaddr=1000000\0" \
"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \ "ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \
......
...@@ -548,7 +548,7 @@ ...@@ -548,7 +548,7 @@
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
...@@ -558,7 +558,7 @@ ...@@ -558,7 +558,7 @@
"consoledev=ttyS0\0" \ "consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \ "ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \ "ramdiskfile=ramfs.83xx\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=mpc832x_mds.dtb\0" \ "fdtfile=mpc832x_mds.dtb\0" \
"" ""
......
...@@ -172,7 +172,6 @@ ...@@ -172,7 +172,6 @@
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
...@@ -701,7 +700,7 @@ ...@@ -701,7 +700,7 @@
#define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0 #define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
...@@ -732,7 +731,7 @@ ...@@ -732,7 +731,7 @@
"update=protect off fe000000 fe03ffff; " \ "update=protect off fe000000 fe03ffff; " \
"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0" \ "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0" \
"upd=run load update\0" \ "upd=run load update\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=mpc8349emds.dtb\0" \ "fdtfile=mpc8349emds.dtb\0" \
"" ""
......
...@@ -589,7 +589,7 @@ ...@@ -589,7 +589,7 @@
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
...@@ -599,7 +599,7 @@ ...@@ -599,7 +599,7 @@
"consoledev=ttyS0\0" \ "consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \ "ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \ "ramdiskfile=ramfs.83xx\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=mpc836x_mds.dtb\0" \ "fdtfile=mpc836x_mds.dtb\0" \
"" ""
......
...@@ -646,7 +646,7 @@ extern int board_pci_host_broken(void); ...@@ -646,7 +646,7 @@ extern int board_pci_host_broken(void);
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
...@@ -656,7 +656,7 @@ extern int board_pci_host_broken(void); ...@@ -656,7 +656,7 @@ extern int board_pci_host_broken(void);
"consoledev=ttyS0\0" \ "consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \ "ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \ "ramdiskfile=ramfs.83xx\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=mpc8379_mds.dtb\0" \ "fdtfile=mpc8379_mds.dtb\0" \
"" ""
......
...@@ -190,8 +190,8 @@ ...@@ -190,8 +190,8 @@
/* 0x3937d322 */ /* 0x3937d322 */
#define CONFIG_SYS_DDR_TIMING_2 0x02984cc8 #define CONFIG_SYS_DDR_TIMING_2 0x02984cc8
#define CONFIG_SYS_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \ #define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (256 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) | (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x06090100 */ /* 0x06090100 */
#if defined(CONFIG_DDR_2T_TIMING) #if defined(CONFIG_DDR_2T_TIMING)
...@@ -205,7 +205,7 @@ ...@@ -205,7 +205,7 @@
/* 0x43000000 */ /* 0x43000000 */
#endif #endif
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ #define CONFIG_SYS_DDR_MODE ((0x0406 << SDRAM_MODE_ESD_SHIFT) \
| (0x0442 << SDRAM_MODE_SD_SHIFT)) | (0x0442 << SDRAM_MODE_SD_SHIFT))
/* 0x04400442 */ /* DDR400 */ /* 0x04400442 */ /* DDR400 */
#define CONFIG_SYS_DDR_MODE2 0x00000000 #define CONFIG_SYS_DDR_MODE2 0x00000000
...@@ -668,7 +668,7 @@ ...@@ -668,7 +668,7 @@
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8379_rdb.dtb #define CONFIG_FDTFILE mpc8379_rdb.dtb
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200 #define CONFIG_BAUDRATE 115200
...@@ -684,7 +684,7 @@ ...@@ -684,7 +684,7 @@
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"ramdiskaddr=1000000\0" \ "ramdiskaddr=1000000\0" \
"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \ "ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \
......
...@@ -250,7 +250,7 @@ extern int tqm834x_num_flash_banks; ...@@ -250,7 +250,7 @@ extern int tqm834x_num_flash_banks;
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI1 host bridge */ /* PCI1 host bridge */
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 #define CONFIG_SYS_PCI1_MEM_BASE 0x90000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE) #define CONFIG_SYS_PCI1_MMIO_BASE (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
......
...@@ -40,24 +40,28 @@ ...@@ -40,24 +40,28 @@
#define CONFIG_MPC8349 1 /* MPC8349 specific */ #define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */ #define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */
#undef CONFIG_PCI
/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */ /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ #undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
#define PCI_66M /*
#ifdef PCI_66M * The default if PCI isn't enabled, or if no PCI clk setting is given
#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ * is 66MHz; this is what the board defaults to when the PCI slot is
#else * physically empty. The board will automatically (i.e w/o jumpers)
* clock down to 33MHz if you insert a 33MHz PCI card.
*/
#ifdef PCI_33M
#define CONFIG_83XX_CLKIN 33000000 /* in Hz */ #define CONFIG_83XX_CLKIN 33000000 /* in Hz */
#else /* 66M */
#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
#endif #endif
#ifndef CONFIG_SYS_CLK_FREQ #ifndef CONFIG_SYS_CLK_FREQ
#ifdef PCI_66M #ifdef PCI_33M
#define CONFIG_SYS_CLK_FREQ 66000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
#else
#define CONFIG_SYS_CLK_FREQ 33000000 #define CONFIG_SYS_CLK_FREQ 33000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
#else /* 66M */
#define CONFIG_SYS_CLK_FREQ 66000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
#endif #endif
#endif #endif
...@@ -153,7 +157,6 @@ ...@@ -153,7 +157,6 @@
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
...@@ -627,7 +630,7 @@ ...@@ -627,7 +630,7 @@
#define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0 #define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
...@@ -654,7 +657,7 @@ ...@@ -654,7 +657,7 @@
"update=protect off ff800000 ff83ffff; " \ "update=protect off ff800000 ff83ffff; " \
"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \ "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
"upd=run load update\0" \ "upd=run load update\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=sbc8349.dtb\0" \ "fdtfile=sbc8349.dtb\0" \
"" ""
......
...@@ -152,7 +152,6 @@ ...@@ -152,7 +152,6 @@
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */
#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
...@@ -555,7 +554,7 @@ ...@@ -555,7 +554,7 @@
#define CONFIG_ROOTPATH /tftpboot/rootfs #define CONFIG_ROOTPATH /tftpboot/rootfs
#define CONFIG_BOOTFILE uImage #define CONFIG_BOOTFILE uImage
#define CONFIG_LOADADDR 500000 /* def location for tftp and bootm */ #define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* boot command will set bootargs */ #undef CONFIG_BOOTARGS /* boot command will set bootargs */
...@@ -582,7 +581,7 @@ ...@@ -582,7 +581,7 @@
"update=protect off fff00000 fff3ffff; " \ "update=protect off fff00000 fff3ffff; " \
"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \ "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
"upd=run load update\0" \ "upd=run load update\0" \
"fdtaddr=400000\0" \ "fdtaddr=780000\0" \
"fdtfile=vme8349.dtb\0" \ "fdtfile=vme8349.dtb\0" \
"" ""
......
...@@ -837,6 +837,9 @@ ...@@ -837,6 +837,9 @@
#define CSCONFIG_EN 0x80000000 #define CSCONFIG_EN 0x80000000
#define CSCONFIG_AP 0x00800000 #define CSCONFIG_AP 0x00800000
#define CSCONFIG_ODT_WR_ACS 0x00010000 #define CSCONFIG_ODT_WR_ACS 0x00010000
#if defined(CONFIG_MPC832x)
#define CSCONFIG_ODT_WR_CFG 0x00040000
#endif
#define CSCONFIG_BANK_BIT_3 0x00004000 #define CSCONFIG_BANK_BIT_3 0x00004000
#define CSCONFIG_ROW_BIT 0x00000700 #define CSCONFIG_ROW_BIT 0x00000700
#define CSCONFIG_ROW_BIT_12 0x00000000 #define CSCONFIG_ROW_BIT_12 0x00000000
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment