Commit d7b6a754 authored by Paul Kocialkowski's avatar Paul Kocialkowski Committed by Tom Rini
Browse files

power: twl6030: Enable VAUX1 for eMMC power, depending on BOOT2 value



This enables the VAUX1 supply, used for eMMC power in standard configurations.
Its voltage is determined by the value of the BOOT2 pin of the TWL6030.

Note that the TWL6030 might already have enabled this regulator at startup
(depending on the value of the BOOT3 pin of the TWL6030), according to the
TWL6030 datasheet.
Signed-off-by: default avatarPaul Kocialkowski <contact@paulk.fr>
parent c5dbae7c
......@@ -214,6 +214,8 @@ void twl6030_init_battery_charging(void)
void twl6030_power_mmc_init()
{
u8 value = 0;
/* 3.0V voltage output for VMMC */
twl6030_i2c_write_u8(TWL6030_CHIP_PM, TWL6030_VMMC_CFG_VOLTAGE,
TWL6030_CFG_VOLTAGE_30);
......@@ -221,6 +223,23 @@ void twl6030_power_mmc_init()
/* Enable P1 output for VMMC */
twl6030_i2c_write_u8(TWL6030_CHIP_PM, TWL6030_VMMC_CFG_STATE,
TWL6030_CFG_STATE_P1 | TWL6030_CFG_STATE_ON);
twl6030_i2c_read_u8(TWL6030_CHIP_PM, TWL6030_PH_STS_BOOT, &value);
/* BOOT2 indicates 1.8V/2.8V VAUX1 for eMMC */
if (value & TWL6030_PH_STS_BOOT2) {
/* 1.8V voltage output for VAUX1 */
twl6030_i2c_write_u8(TWL6030_CHIP_PM, TWL6030_VAUX1_CFG_VOLTAGE,
TWL6030_CFG_VOLTAGE_18);
} else {
/* 2.8V voltage output for VAUX1 */
twl6030_i2c_write_u8(TWL6030_CHIP_PM, TWL6030_VAUX1_CFG_VOLTAGE,
TWL6030_CFG_VOLTAGE_28);
}
/* Enable P1 output for VAUX */
twl6030_i2c_write_u8(TWL6030_CHIP_PM, TWL6030_VAUX1_CFG_STATE,
TWL6030_CFG_STATE_P1 | TWL6030_CFG_STATE_ON);
}
void twl6030_usb_device_settings()
......
......@@ -20,6 +20,15 @@
#define TWL6030_CHIP_PWM 0x49
/* Slave Address 0x48 */
#define TWL6030_PH_STS_BOOT 0x29
#define TWL6030_PH_STS_BOOT0 (1 << 0)
#define TWL6030_PH_STS_BOOT1 (1 << 1)
#define TWL6030_PH_STS_BOOT2 (1 << 2)
#define TWL6030_PH_STS_BOOT3 (1 << 3)
#define TWL6030_VAUX1_CFG_STATE 0x86
#define TWL6030_VAUX1_CFG_VOLTAGE 0x87
#define TWL6030_VMMC_CFG_STATE 0x9A
#define TWL6030_VMMC_CFG_VOLTAGE 0x9B
#define TWL6030_VUSB_CFG_STATE 0xA2
......@@ -27,6 +36,8 @@
#define TWL6030_CFG_GRP_P1 (1 << 0)
#define TWL6030_CFG_STATE_ON (1 << 0)
#define TWL6030_CFG_STATE_P1 (TWL6030_CFG_GRP_P1 << 5)
#define TWL6030_CFG_VOLTAGE_18 0x09
#define TWL6030_CFG_VOLTAGE_28 0x13
#define TWL6030_CFG_VOLTAGE_30 0x15
#define MISC1 0xE4
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment