Commit e46fedfe authored by Timur Tabi's avatar Timur Tabi Committed by Kumar Gala
Browse files

powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros

Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. ...
parent b6c3722d
......@@ -2862,6 +2862,43 @@ Low Level (hardware related) configuration options:
and RPXsuper) to be able to adjust the position of
the IMMR register after a reset.
- CONFIG_SYS_CCSRBAR_DEFAULT:
Default (power-on reset) physical address of CCSR on Freescale
PowerPC SOCs.
- CONFIG_SYS_CCSRBAR:
Virtual address of CCSR. On a 32-bit build, this is typically
the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
for cross-platform code that uses that macro instead.
- CONFIG_SYS_CCSRBAR_PHYS:
Physical address of CCSR. CCSR can be relocated to a new
physical address, if desired. In this case, this macro should
be set to that address. Otherwise, it should be set to the
same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
is typically relocated on 36-bit builds. It is recommended
that this macro be defined via the _HIGH and _LOW macros:
#define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
* 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
- CONFIG_SYS_CCSRBAR_PHYS_HIGH:
Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
either 0 (32-bit build) or 0xF (36-bit build). This macro is
used in assembly code, so it must not contain typecasts or
integer size suffixes (e.g. "ULL").
- CONFIG_SYS_CCSRBAR_PHYS_LOW:
Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
used in assembly code, so it must not contain typecasts or
integer size suffixes (e.g. "ULL").
- CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
forced to a value that ensures that CCSR is not relocated.
- Floppy Disk Support:
CONFIG_SYS_FDC_DRIVE_NUMBER
......
......@@ -23,6 +23,10 @@
/* SoC specific defines for Freescale MPC85xx (PQ3) and QorIQ processors */
#ifdef CONFIG_SYS_CCSRBAR_DEFAULT
#error "Do not define CONFIG_SYS_CCSRBAR_DEFAULT in the board header file."
#endif
/* Number of TLB CAM entries we have on FSL Book-E chips */
#if defined(CONFIG_E500MC)
#define CONFIG_SYS_NUM_TLBCAMS 64
......@@ -34,34 +38,41 @@
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8540)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8541)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8544)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8548)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8555)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8560)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8568)
#define CONFIG_MAX_CPUS 1
......@@ -70,6 +81,7 @@
#define QE_MURAM_SIZE 0x10000UL
#define MAX_QE_RISC 2
#define QE_NUM_OF_SNUM 28
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8569)
#define CONFIG_MAX_CPUS 1
......@@ -78,11 +90,13 @@
#define QE_MURAM_SIZE 0x20000UL
#define MAX_QE_RISC 4
#define QE_NUM_OF_SNUM 46
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8572)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_DDR_115
#define CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134
......@@ -106,6 +120,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
......@@ -116,6 +131,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define QE_MURAM_SIZE 0x6000UL
......@@ -128,6 +144,7 @@
#define CONFIG_SYS_FSL_NUM_LAWS 12
#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_FSL_SATA_ERRATUM_A001
......@@ -151,6 +168,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
......@@ -166,6 +184,7 @@
#define QE_MURAM_SIZE 0x6000UL
#define MAX_QE_RISC 1
#define QE_NUM_OF_SNUM 28
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
/* P1017 is single core version of P1023 */
#elif defined(CONFIG_P1017)
......@@ -179,6 +198,7 @@
#define CONFIG_SYS_BMAN_NUM_PORTALS 3
#define CONFIG_SYS_FM_MURAM_SIZE 0x10000
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000
#elif defined(CONFIG_P1020)
#define CONFIG_MAX_CPUS 2
......@@ -186,6 +206,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
......@@ -195,6 +216,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define QE_MURAM_SIZE 0x6000UL
......@@ -206,6 +228,7 @@
#define CONFIG_SYS_FSL_NUM_LAWS 12
#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_FSL_SATA_ERRATUM_A001
......@@ -221,6 +244,7 @@
#define CONFIG_SYS_BMAN_NUM_PORTALS 3
#define CONFIG_SYS_FM_MURAM_SIZE 0x10000
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000
/* P1024 is lower end variant of P1020 */
#elif defined(CONFIG_P1024)
......@@ -229,6 +253,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
......@@ -239,6 +264,7 @@
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define QE_MURAM_SIZE 0x6000UL
......@@ -250,6 +276,7 @@
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
......@@ -257,6 +284,7 @@
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
......@@ -271,6 +299,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 32
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_USB1_PHY_ENABLE
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
......@@ -288,6 +317,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 32
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_USB1_PHY_ENABLE
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
......@@ -305,6 +335,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 32
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_USB1_PHY_ENABLE
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
......@@ -318,6 +349,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 16
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,p4080-pcie"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#elif defined(CONFIG_PPC_P4080)
#define CONFIG_MAX_CPUS 8
......@@ -333,6 +365,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 16
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,p4080-pcie"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_ERRATUM_CPC_A002
#define CONFIG_SYS_FSL_ERRATUM_CPC_A003
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003
......@@ -359,6 +392,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 32
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_USB1_PHY_ENABLE
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
......@@ -376,6 +410,7 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
#define CONFIG_SYS_FSL_TBCLK_DIV 32
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_USB1_PHY_ENABLE
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
......@@ -385,4 +420,8 @@
#error Processor type not defined for this platform
#endif
#ifndef CONFIG_SYS_CCSRBAR_DEFAULT
#error "CONFIG_SYS_CCSRBAR_DEFAULT is not defined for this platform."
#endif
#endif /* _ASM_MPC85xx_CONFIG_H_ */
......@@ -127,22 +127,11 @@
#define CONFIG_SYS_L2_SIZE (512 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
#endif
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR
#else
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* DDR Setup */
......
......@@ -89,15 +89,8 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR1
......
......@@ -62,14 +62,8 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR1
......
......@@ -74,14 +74,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR2
......
......@@ -77,14 +77,8 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR2
......
......@@ -62,14 +62,8 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR1
......
......@@ -86,15 +86,8 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR1
......
......@@ -71,14 +71,8 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR2
......
......@@ -105,20 +105,11 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_L2_SIZE (512 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
/* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
/* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR
#else
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* DDR Setup */
......
......@@ -112,22 +112,11 @@
#define CONFIG_SYS_L2_SIZE (512 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#endif
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR
#else
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* DDR Setup */
......
......@@ -64,18 +64,8 @@
#define CONFIG_SYS_MEMTEST_START 0x00000000
#define CONFIG_SYS_MEMTEST_END 0x7fffffff
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull
#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
#endif
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_DDR_SPD
......
......@@ -99,15 +99,6 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_LBC_LBCR 0x00000000 /* Implement conversion of
addresses in the LBC */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xff600000 /* relocated CCSRBAR */
/* physical addr of CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
......
......@@ -148,24 +148,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_SYS_L2_SIZE (512 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull
#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
#endif
/* CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */
/* CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR
#else
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* DDR Setup */
......
......@@ -118,18 +118,8 @@
#define CONFIG_SYS_L2_SIZE (512 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#endif
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
......
......@@ -138,20 +138,6 @@
#define CONFIG_SYS_L3_SIZE (1024 << 10)
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xfe000000 /* relocated CCSRBAR */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CCSRBAR_PHYS 0xffe000000ull
#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
#endif
/* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
......
......@@ -94,20 +94,6 @@
#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
#endif
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#if XXX
#define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
#else
#define CONFIG_SYS_CCSRBAR 0xff700000 /* default CCSRBAR */
#endif
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
/* DDR Setup */
......
......@@ -130,18 +130,12 @@
#define CONFIG_SYS_MEMTEST_START 0x00000000
#define CONFIG_SYS_MEMTEST_END 0x10000000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
#ifdef CONFIG_TQM_BIGFLASH
#define CONFIG_SYS_CCSRBAR 0xA0000000 /* relocated CCSRBAR */
#else /* !CONFIG_TQM_BIGFLASH */
#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
#endif /* CONFIG_TQM_BIGFLASH */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */