1. 22 Jul, 2009 2 commits
  2. 04 Apr, 2009 2 commits
  3. 17 Feb, 2009 1 commit
    • Peter Tyser's avatar
      86xx: Reset update · 4ef630df
      Peter Tyser authored
      Update the 86xx reset sequence to try executing a board-specific reset
      function.  If the board-specific reset is not implemented or does not
      succeed, then assert #HRESET_REQ.  Using #HRESET_REQ is a more standard
      reset procedure than the previous method and allows all board
      peripherals to be reset if needed.
      Signed-off-by: default avatarPeter Tyser <ptyser@xes-inc.com>
  4. 13 Jan, 2009 1 commit
  5. 03 Nov, 2008 1 commit
  6. 02 Nov, 2008 1 commit
  7. 30 Oct, 2008 1 commit
  8. 24 Oct, 2008 1 commit
  9. 18 Oct, 2008 1 commit
  10. 03 Sep, 2008 1 commit
  11. 27 Aug, 2008 2 commits
  12. 10 Jul, 2008 1 commit
  13. 19 Jun, 2008 1 commit
  14. 12 Jun, 2008 1 commit
    • Becky Bruce's avatar
      Change initdram() return type to phys_size_t · 9973e3c6
      Becky Bruce authored
      This patch changes the return type of initdram() from long int to phys_size_t.
      This is required for a couple of reasons: long int limits the amount of dram
      to 2GB, and u-boot in general is moving over to phys_size_t to represent the
      size of physical memory.  phys_size_t is defined as an unsigned long on almost
      all current platforms.
      This patch *only* changes the return type of the initdram function (in
      include/common.h, as well as in each board's implementation of initdram).  It
      does not actually modify the code inside the function on any of the platforms;
      platforms which wish to support more than 2GB of DRAM will need to modify
      their initdram() function code.
      Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
      Signed-off-by: default avatarBecky Bruce <becky.bruce@freescale.com>
  15. 19 May, 2008 1 commit
  16. 29 Apr, 2008 1 commit
  17. 04 Mar, 2008 1 commit
  18. 20 Feb, 2008 1 commit
    • Jon Loeliger's avatar
      86xx: Fix GUR PCI config registers properly. · a551cee9
      Jon Loeliger authored
      Back in commit 975a083a
      I tried to "8610HPCD: Fix typos in two PCI setup registers", I
      botched it due to not realizing that 8610 and 8641 had different
      Global Utility Register defintions, one of which was like 85xx,
      and the other wasn't.  Correct this problem by introducing two
      symbols, one for each 86xx SoC, but neither of which is named
      anything like 85xx.
      My bad.  Lovely Wednesday with git bisect.  You know.
      Signed-off-by: default avatarJon Loeliger <jdl@freescale.com>
  19. 19 Feb, 2008 1 commit
  20. 09 Jan, 2008 2 commits
  21. 07 Nov, 2007 1 commit
    • York Sun's avatar
      8610: Add 8610 DIU display driver · a877880c
      York Sun authored
      1280x1024 and 1024x768 @ 32 bpp are supported now.
      DVI, Single-link LVDS, Double-link LVDS are all supported.
      Environmental variable "monitor" is used to specify monitor port.
      A new command "diufb" is introduced to reinitialize monitor
      and display a BMP file in the memory. So far, 1-bit, 4-bit,
      8-bit and 24-bit BMP formats are supported.
          diufb init
              - initialize the diu driver
          Enable the port specified in the environmental variable "monitor"
          diufb addr
              - display bmp file in memory.
          The bmp image should be no bigger than the resolution, 1280x1024
          for DVI and double-link LVDS, 1024x768 for single-link LVDS.
      Note, this driver allocate memory but doesn't free it after use
      It is written on purpose -- to avoid a failure of reallocation
      due to memory fragement.
      ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
      Signed-off-by: default avatarYork Sun <yorksun@freescale.com>
      Signed-off-by: default avatarJon loeliger <jdl@freescale.com>
  22. 17 Oct, 2007 1 commit