Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R
Signed-off-by: Tom Rini <trini@ti.com>

We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R
Signed-off-by: Tom Rini <trini@ti.com>

OMAP4/5 had an empty arch_cpu_init() so drop that along with
CONFIG_ARCH_CPU_INIT
Signed-off-by: Tom Rini <trini@ti.com>

This is only used on !CONFIG_GENERIC_MMC which is false here.
Signed-off-by: Tom Rini <trini@ti.com>

As ttyS0 is no longer valid for newer OMAP kernels, and pandora serial
cables are not widespread, simply drop console argument. This should
allow booting old and new kernels with default arguments, and those who
need serial can use a boot script on SD card.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>

Update pandora's GPIO setup code with these changes:
- convert to gpiolib
- set up dual voltage GPIOs to match supply of 1.8V by clearing VMODE1
- add GPIO_IO_PWRDNZ configuration for DM3730 variation of pandora
  (required to enable GPIO 126, 127, and 129 I/O cells in DM3730)
- add wifi reset pulse as recommended by wifi chip's manufacturer
- drop configuration of GPIOs that u-boot doesn't need
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>

DM3730 needs some additional pin mux configuration for GPIOs
126-129 to work, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>

This rule confirms that if we're on ARM and we have enabled THUMB builds
that we have a new enough toolchain to produce a working binary.

Changes in v2:
- Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F)
- Simplfy checkthumb test after doing the above
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Added from Linux - commit fde7d9049e55ab85a390be7f415d74c9f62dd0f9
Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>

Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.

Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: Aneesh V <aneesh@ti.com>

Enable -march=armv7-a for armv7 platforms if the tool-chain
supports it. This in turn results in Thumb-2 code generated
for these platforms if CONFIG_SYS_THUMB_BUILD is enabled.
Signed-off-by: Aneesh V <aneesh@ti.com>

Enable Thumb build and ARM-Thumb interworking based on the new
config flag CONFIG_SYS_THUMB_BUILD
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>

Warm reset is not functional in case of omap5430ES1.0.
So override the weak reset_cpu function to use
cold reset instead.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Save env to eMMC
Signed-off-by: Balaji T K <balajitk@ti.com>

Add omap5 pbias configuration for mmc1/sd lines
and set voltage for sd data i/o lines
Signed-off-by: Balaji T K <balajitk@ti.com>

palmas/TWL6035 is power IC for omap5 evm boards
Signed-off-by: Balaji T K <balajitk@ti.com>

In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The ddr part name used in OMAP5 ES1.0 soc is a SAMSUNG part and
not a ELPIDA part. So change this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Adding the nessecary changes for OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Add support to identify the device as GP/EMU/HS.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The break statement is missing in init_omap_revision function, resulting
in a wrong revision identification. So fixing this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.

Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
	http://lists.denx.de/pipermail/u-boot/2012-March/119151.htmlSigned-off-by: R Sricharan <r.sricharan@ti.com>

The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Adding the full pinmux data for OMAP5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>

This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.

On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.

More than 200 duplicated lines have been deleted.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>

OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.

As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.

With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.

NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>