1. 07 Feb, 2014 1 commit
    • Alexey Brodkin's avatar
      net/designware - switch driver to phylib usage · 92a190aa
      Alexey Brodkin authored
      
      
      With this change driver will benefit from existing phylib and thus
      custom phy functionality implemented in the driver will go away:
       * Instantiation of the driver is now much shorter - 2 parameters
      instead of 4.
       * Simplified phy management/functoinality in driver is replaced with
      rich functionality of phylib.
       * Support of custom phy initialization is now done with existing
      "board_phy_config".
      
      Note that after this change some previously used config options
      (driver-specific PHY configuration) will be obsolete and they are simply
      substituted with similar options of phylib.
      
      For example:
       * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
      by default.
       * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
      explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
      automatically the first discovered on MDIO bus phy will be used
      
      I believe there's no need now in "doc/README.designware_eth" because
      user only needs to instantiate the driver with "designware_initialize"
      whose prototype exists in "include/netdev.h".
      
      Cc: Joe Hershberger <joe.hershberger@ni.com>
      Cc: Vipin Kumar <vipin.kumar@st.com>
      Cc: Stefan Roese <sr@denx.de>
      Cc: Mischa Jonker <mjonker@synopsys.com>
      Cc: Shiraz Hashim <shiraz.hashim@st.com>
      Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
      Cc: Amit Virdi <amit.virdi@st.com>
      Cc: Sonic Zhang <sonic.zhang@analog.com>
      Signed-off-by: default avatarAlexey Brodkin <abrodkin@synopsys.com>
      92a190aa
  2. 24 Jul, 2013 1 commit
  3. 04 Oct, 2012 1 commit
    • Stefan Roese's avatar
      ARM: Add X600 board support (SPEAr600 based) · 995b72dd
      Stefan Roese authored
      
      
      This patch adds support for the X600 SPEAr600 based board. Its also
      the first SPEAr600 board that uses the newly introduced SPEAr600
      SPL support. Xloader is not necessary any more. By using the new
      "u-boot.spr" make target, one image will generated containing both,
      U-Boot SPL (with mkimage header as needed by the SPEAr BootROM, and
      the main U-Boot with mkimage header.
      Signed-off-by: default avatarStefan Roese <sr@denx.de>
      Cc: Amit Virdi <amit.virdi@st.com>
      Cc: Vipin Kumar <vipin.kumar@st.com>
      995b72dd
  4. 07 Jul, 2012 3 commits
  5. 21 Mar, 2010 1 commit
  6. 23 Jan, 2010 2 commits
  7. 01 Sep, 2009 2 commits
  8. 18 Oct, 2008 1 commit
  9. 23 Oct, 2007 1 commit
  10. 27 Nov, 2006 1 commit
  11. 30 May, 2006 1 commit
  12. 23 May, 2006 1 commit
  13. 10 Oct, 2004 1 commit
    • wdenk's avatar
      Patches by Scott McNutt, 24 Aug 2004: · 5c952cf0
      wdenk authored
      - Add support for Altera Nios-II processors.
      - Add support for Psyent PCI-5441 board.
      - Add support for Psyent PK1C20 board.
      5c952cf0
  14. 08 Dec, 2003 1 commit
  15. 07 Nov, 2003 1 commit
  16. 29 Oct, 2003 1 commit
    • wdenk's avatar
      * Prepare for release · 5fa66df6
      wdenk authored
      * Fix problems in memory test on some boards (which was not
        non-destructive as intended)
      
      * Patch by Gary Jennejohn, 28 Oct 2003:
        Change fs/fat/fat.c to put I/O buffers in BSS instead on the stack
        to prevent stack overflow on ARM systems
      5fa66df6
  17. 11 Sep, 2003 1 commit
    • wdenk's avatar
      * Patch by Gary Jennejohn, 11 Sep 2003: · a43278a4
      wdenk authored
        - allow for longer timeouts for USB mass storage devices
      
      * Patch by Denis Peter, 11 Sep 2003:
        - fix USB data pointer assignment for bulk only transfer.
        - prevent to display erased directories in FAT filesystem.
      
      * Change output format for NAND flash - make it look like for other
        memory, too
      a43278a4
  18. 31 Aug, 2003 1 commit
    • wdenk's avatar
      Patch by Yuli Barcohen, 7 Aug 2003: · 326428cc
      wdenk authored
      According to the MPC8260 User's Manual, PCI_MODE signal should be
      reflected in SCCR register, and local bus pins configuration is taken
      from HRCW and appears in SIUMCR. For some reason it does not work
      this way, so the only possibility to detect if the board is
      configured in PCI mode is to check the BCSR. This patch sets SCCR and
      SIUMCR according to the BCSR.
      326428cc
  19. 28 Aug, 2003 1 commit
  20. 17 Aug, 2003 1 commit
    • wdenk's avatar
      * Make Ethernet autonegotiation on INCA-IP work for all clock rates; · e0ac62d7
      wdenk authored
        allow selection of clock frequency as "make" target
      
      * Implement memory autosizing code for IceCube boards
      
      * Configure network port on INCA-IP for autonegotiation
      
      * Fix overflow problem in network timeout code
      
      * Patch by Richard Woodruff, 8 Aug 2003:
        Allow crc32 to be used at address 0x000 (crc32_no_comp, too).
      e0ac62d7
  21. 17 Jul, 2003 1 commit
    • wdenk's avatar
      * Patch by Martin Krause, 17 Jul 2003: · 2535d602
      wdenk authored
        add delay to get I2C working with "imm" command and s3c24x0_i2c.c
      
      * Patch by Richard Woodruff, 17 July 03:
        - Fixed bug in OMAP1510 baud rate divisor settings.
      
      * Patch by Nye Liu, 16 July 2003:
        MPC860FADS fixes:
        - add MPC86xADS support (uses MPC86xADS.h)
        - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
          o PLPRCR changes
          o BRG changes (EXTAL/XTAL restricted to 10MHz)
          o don't trust gclk() software measurement by default, depend on
            CONFIG_8xx_GCLK_FREQ
        - add DRAM SIMM not installed detection
        - use more "correct" SDRAM initialization sequence
        - allow different SDRAM sizes (8xxADS has 8M)
        - default DER is 0
        - remove unused MAMR defines from FADS860T.h (all done in fads.c)
        - rename MAMR/MBMR defines to be more consistent. Should eventually
          be merged into MxMR to better reflect the PowerQUICC datasheet.
      
      * Patch by Yuli Barcohen, 16 Jul 2003:
        support new Motorola PQ2FADS-ZU evaluation board which replaced
        MPC8260ADS and MPC8266ADS
      2535d602
  22. 16 Jul, 2003 1 commit
  23. 14 Jul, 2003 1 commit
    • wdenk's avatar
      * Patches by Yuli Barcohen, 13 Jul 2003: · 8564acf9
      wdenk authored
        - Correct flash and JFFS2 support for MPC8260ADS
        - fix PVR values and clock generation for PowerQUICC II family
          (8270/8275/8280)
      
      * Patch by Bernhard Kuhn, 08 Jul 2003:
        - add support for M68K targets
      
      * Patch by Ken Chou, 3 Jul:
        - Fix PCI config table for A3000
        - Fix iobase for natsemi.c
          (PCI_BASE_ADDRESS_0 is the IO base register for DP83815)
      
      * Allow to enable "slow" POST routines by key press on power-on
      * Fix temperature dependend switching of LCD backlight on LWMON
      * Tweak output format for LWMON
      8564acf9
  24. 30 Jun, 2003 1 commit
    • wdenk's avatar
      * Patch by Seb James, 30 Jun 2003: · b37c7e5e
      wdenk authored
        Improve documentation of I2C configuration in README
      
      * Fix problems with previous log buffer "fixes"
      
      * Fix minor help text issues
      
      * "log append" did not append a newline
      b37c7e5e
  25. 27 Jun, 2003 1 commit
    • wdenk's avatar
      * Code cleanup: · 8bde7f77
      wdenk authored
        - remove trailing white space, trailing empty lines, C++ comments, etc.
        - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
      
      * Patches by Kenneth Johansson, 25 Jun 2003:
        - major rework of command structure
          (work done mostly by Michal Cendrowski and Joakim Kristiansen)
      8bde7f77
  26. 26 Jun, 2003 1 commit
  27. 27 Apr, 2003 1 commit
    • wdenk's avatar
      * LWMON extensions: · 4532cb69
      wdenk authored
        - Splashscreen support
        - modem support
        - sysmon support
        - temperature dependend enabling of LCD
      
      * Allow booting from old "PPCBoot" disk partitions
      
      * Add support for TQM8255 Board / MPC8255 CPU
      4532cb69
  28. 10 Apr, 2003 1 commit
  29. 08 Apr, 2003 1 commit
    • wdenk's avatar
      Prepare for 0.3.0 release · 60fbe254
      wdenk authored
      * Add support for Purple Board (MIPS64 5Kc)
      
      * Add support for MIPS64 5Kc CPUs
      60fbe254
  30. 28 Feb, 2003 1 commit
    • wdenk's avatar
      * Add support for 16 MB flash configuration of TRAB board · 6069ff26
      wdenk authored
      * Patch by Erwin Rol, 27 Feb 2003:
        Add support for RTEMS
      
      * Add image information to README
      
      * Fix dual PCMCIA slot support (when running with just one
        slot populated)
      
      * Add VFD type detection to trab board
      
      * extend drivers/cs8900.c driver to synchronize  ethaddr  environment
        variable with value in the EEPROM
      
      * Start adding MIPS support files
      6069ff26
  31. 13 Jan, 2003 1 commit
  32. 20 Dec, 2002 1 commit
  33. 17 Dec, 2002 1 commit
  34. 03 Nov, 2002 2 commits
  35. 14 Dec, 2000 1 commit