This fix will make the MAL burst disabling patch for the Linux
EMAC driver obsolete.

Signed-off-by: Stefan Roese <sr@denx.de>

This code will optimize the DDR2 controller setup on a board specific
basis.

Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.

Signed-off-by: Stefan Roese <sr@denx.de>

  - fix a typo in V38B config file
  - move watchdog initialisation earlier in the boot process
  - add "wdt=off" to default kernel command line (disables kernel watchdog)

Fix cfi failure with Spansion Flash (Spansion Flash Devices have a different offset to go into CFI mode)

Now 32MByte and 64MByte FLASH is know to work and other
configurations should work too.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

The soc node of the mpc52xx needs to be loaded with the IPB bus frequency,
not the XLB frequency.

This patch depends on the previous patches for MPC52xx device tree support

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>

This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".

Signed-off-by: Stefan Roese <sr@denx.de>

In the bootvx command the load address was only read from the env
variable "loadaddr" and not optionally passed as paramter as described
in the help. This is fixed with this patch. The behaviour is now the
same as in the bootelf command.

Signed-off-by: Stefan Roese <sr@denx.de>

Fixed include/ppc440.c for UIC address Bug

Corrects bug affecting the addresses for the universal interrupt
controller UIC2 and UIC3 on the PPC440 Epx, GRx, and SPE chips.

Signed-off-by: Jeff Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Timur Tabi <timur@freescale.com>

Signed-off-by: Timur Tabi <timur@freescale.com>

Dave for mpc8360emds, and me for mpc8349emds.

give initial values for reg_num, shift, p_cmxucr in ucc_set_clk_src
since they are passed by reference to ucc_get_cmxucr_reg and assigned.

Implement various code style fixes and similar changes.

Signed-off-by: Timur Tabi <timur@freescale.com>

This patch adds the code and configuration necessary to boot with an
arch/powerpc Linux kernel.

Signed-off-by: Grant Likely <grant.likely@gmail.com>
Acked-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Patch below corrects the setting of the zmiifer register, it was
overwritting the register rather than ORing the settings.

Signed-off-by: Neil Wilson <NWilson@airspan.com>
Signed-off-by: Stefan Roese <sr@denx.de>

The current NAND Bootloader setup forces the environment
variables to be in line with the bootloader. This change
enables the configuration to be made in the board include
file instead so that it can be individually enabled.

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>