1. 13 Jul, 2010 1 commit
  2. 12 Jul, 2010 1 commit
    • Eric Bénard's avatar
      cpuat91: unbreak ethernet · 836cd453
      Eric Bénard authored
      
      
      * the following problems are met :
      config was set to use the new driver as a default but
      - RMII was not enabled for the new driver
      - the new driver didn't compile with RMII enabled
      - the new driver initialize a PHY at address O when the PHY of
      this board is at 1 thus we get "AT91 EMAC RMII: No PHY present"
      
      * to fix these problems, this patch :
      - enable RMII for the new driver
      - fix the wrong define used in the at91_emac.c
      - allow the config file to set a default phy address (and use
      0 as a default as in the actual at91_emac.c driver)
      Signed-off-by: default avatarEric Bénard <eric@eukrea.com>
      Signed-off-by: default avatarBen Warren <biggerbadderben@gmail.com>
      836cd453
  3. 04 Jul, 2010 1 commit
  4. 01 Jul, 2010 1 commit
  5. 29 Jun, 2010 3 commits
  6. 23 Jun, 2010 2 commits
    • Wolfgang Denk's avatar
      Remove AmigaOneG3SE board · 953b7e62
      Wolfgang Denk authored
      
      
      The AmigaOneG3SE board has been orphaned or a very long time, and
      broken for more than 12 releases resp. more than 3 years.  As nobody
      seems to be interested any more in this stuff we may as well ged rid
      of it, especially as it clutters many areas of the code so it is a
      continuous pain for all kinds of ongoing work.
      Signed-off-by: default avatarWolfgang Denk <wd@denx.de>
      953b7e62
    • Wolfgang Denk's avatar
      Get rid of bogus CONFIG_SYS_BUS_HZ and CONFIG_SYS_CONFIG_BUS_CLK definitions · ee80fa7b
      Wolfgang Denk authored
      
      
      CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
      redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
      bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
      funtionality.  Change all this to use CONFIG_SYS_BUS_CLK consistently.
      Signed-off-by: default avatarWolfgang Denk <wd@denx.de>
      Cc: Frank Gottschling <fgottschling@eltec.de>
      Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
      Cc: Eran Man <eran@nbase.co.il>
      Cc: Stefan Roese <sr@denx.de>
      Cc: Nye Liu <nyet@zumanetworks.com>
      Cc: Roy Zang <tie-fei.zang@freescale.com>
      ee80fa7b
  7. 22 Jun, 2010 1 commit
    • Prakash PM's avatar
      DaVinci: EMAC: Get EMAC_MDIO_PHY_NUM from config files · e6441c4f
      Prakash PM authored
      
      
      Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
      Because of this, EMAC does not work on EVMs which do not have phy
      connected at 1. Moving the macro to board config file makes this
      configurable depending on where the phy is connected on the MDIO bus.
      
      This patch fixes the board reset issue observed during network access
      on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
      but it is 0 on DM365EVM.
      
      This patch is verified on da830/omap-l137, dm365 and dm644x evms.
      Signed-off-by: default avatarPrakash PM <prakash.pm@ti.com>
      Signed-off-by: default avatarSandeep Paulraj <s-paulraj@ti.com>
      e6441c4f
  8. 17 Jun, 2010 2 commits
  9. 14 Jun, 2010 1 commit
  10. 10 Jun, 2010 1 commit
  11. 08 Jun, 2010 6 commits
  12. 07 Jun, 2010 6 commits
  13. 06 Jun, 2010 1 commit
    • Asen Dimov's avatar
      add new board pm9g45 · b5d289fc
      Asen Dimov authored
      
      
      Add the new board PM9G45 from Ronetix GmbH.
      * AT91SAM9G45 MCU at 400Mhz.
      * 128MB DDR2 SDRAM
      * 256MB NAND
      * 10/100 MBits Ethernet DP83848
      * Serial number chip DS2401
      
      The board is made as SODIMM200 module.
      For more info www.ronatix.at or info@ronetix.at.
      Signed-off-by: default avatarAsen Dimov <dimov@ronetix.at>
      b5d289fc
  14. 04 Jun, 2010 1 commit
  15. 28 May, 2010 2 commits
  16. 19 May, 2010 1 commit
  17. 17 May, 2010 1 commit
  18. 07 May, 2010 2 commits
  19. 05 May, 2010 6 commits