1. 12 Mar, 2012 5 commits
  2. 06 Mar, 2012 17 commits
  3. 04 Mar, 2012 3 commits
    • Thomas Weber's avatar
      b199c6e2
    • Linus Walleij's avatar
      integrator: remove fragile delay loop from PCI code · fca94c3f
      Linus Walleij authored
      
      
      The reference implementation of the PCI initialization code almost
      everywhere contain this fragile loop of "a few usecs", and its
      use of volatile variables to delay a number of bus cycles is indeed
      uncertain.
      
      Reading the manual "Integrator/AP Users Guide", page 5-15 it is
      clearly stated:
      
      "Wait until 230ms after the end of the reset period before
      accessing V360EPC internal registers. The V360EPC supports the
      use of a serial configuration PROM and the software must wait for
      the device to detect the absence of this PROM before accessing any
      registers. The required delay is a function of the PCI Clock, but
      at the lower frequency (25MHz) is 230ms".
      
      So let's simply wait 230ms per the spec.
      
      This solves the compilation error that looked like this:
      pci.c: In function ‘pci_init_board’:
      pci.c:286:18: warning: variable ‘j’ set but not used
      Reported-by: default avatarWolfgang Denk <wd@denx.de>
      Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
      fca94c3f
    • Linus Walleij's avatar
      pci: move pciauto_config_init() to pci.h · a1e47b66
      Linus Walleij authored
      
      
      Fixing build regressions for the Integrator I get find that a few
      boards try to work around the missing declaration of
      pciauto_config_init() by declaring it in the local scope. This
      does not make sense when the sibling functions are in <pci.h>
      so move the function to the header, ridding the build error
      in the Integrator and getting rid of the local declarations
      here and there.
      Reported-by: default avatarWolfgang Denk <wd@denx.de>
      Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
      a1e47b66
  4. 03 Mar, 2012 13 commits
  5. 29 Feb, 2012 1 commit
    • prabhakar.csengg@gmail.com's avatar
      Ethernut 5: fix build error · 2271e7c6
      prabhakar.csengg@gmail.com authored
      
      
      Fix build error for ethernut5 board due to prototype change
      for function board_mmc_getcd().
      ethernut5.c:238: error: conflicting types for 'board_mmc_getcd'
      u-boot/include/mmc.h:318: note: previous declaration of 'board_mmc_getcd'
      was here
      make[2]: *** [ethernut5.o] Error 1
      Signed-off-by: default avatarPrabhakar Lad <prabhakar.csengg@gmail.com>
      Cc: Tim Schendekehl <tim.schendekehl@egnite.de>
      Cc: Thierry Reding <thierry.reding@avionic-design.de>
      Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
      Cc: egnite GmbH <info@egnite.de>
      2271e7c6
  6. 28 Feb, 2012 1 commit
    • Tom Rini's avatar
      cmd_nand.c: Fix 'nand dump' after latest MTD resync · cfdae12f
      Tom Rini authored
      With 2a8e0fc8
      
       nand_do_read_ops changed in behavior slightly (keeping in sync
      with the kernel which did this change in b64d39d8) such that the OOB data is
      always copied into oobbuf and never appended to datbuf.  Within U-Boot only
      the nand_dump function (for the dump nand subcommand) was expecting the OOB
      data to only be appended to datbuf.  So we now change nand_dump to not
      malloc extra space, correct the comment about datbuf and OOB data and switch
      the pointer to oobbuf before printing.
      
      Cc: Scott Wood <scottwood@freescale.com>
      Signed-off-by: default avatarTom Rini <trini@ti.com>
      Signed-off-by: default avatarScott Wood <scottwood@freescale.com>
      cfdae12f