cadence_qspi_apb.c 23.4 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
/*
 * Copyright (C) 2012 Altera Corporation <www.altera.com>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *  - Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *  - Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *  - Neither the name of the Altera Corporation nor the
 *    names of its contributors may be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED. IN NO EVENT SHALL ALTERA CORPORATION BE LIABLE FOR ANY
 * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#include <common.h>
#include <asm/io.h>
#include <asm/errno.h>
31
#include <wait_bit.h>
32
#include <spi.h>
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
#include "cadence_qspi.h"

#define CQSPI_REG_POLL_US			(1) /* 1us */
#define CQSPI_REG_RETRY				(10000)
#define CQSPI_POLL_IDLE_RETRY			(3)

#define CQSPI_FIFO_WIDTH			(4)

#define CQSPI_REG_SRAM_THRESHOLD_WORDS		(50)

/* Transfer mode */
#define CQSPI_INST_TYPE_SINGLE			(0)
#define CQSPI_INST_TYPE_DUAL			(1)
#define CQSPI_INST_TYPE_QUAD			(2)

#define CQSPI_STIG_DATA_LEN_MAX			(8)

#define CQSPI_DUMMY_CLKS_PER_BYTE		(8)
#define CQSPI_DUMMY_BYTES_MAX			(4)


#define CQSPI_REG_SRAM_FILL_THRESHOLD	\
	((CQSPI_REG_SRAM_SIZE_WORD / 2) * CQSPI_FIFO_WIDTH)
/****************************************************************************
 * Controller's configuration and status register (offset from QSPI_BASE)
 ****************************************************************************/
#define	CQSPI_REG_CONFIG			0x00
#define	CQSPI_REG_CONFIG_CLK_POL_LSB		1
#define	CQSPI_REG_CONFIG_CLK_PHA_LSB		2
62 63 64 65
#define	CQSPI_REG_CONFIG_ENABLE_MASK		BIT(0)
#define	CQSPI_REG_CONFIG_DIRECT_MASK		BIT(7)
#define	CQSPI_REG_CONFIG_DECODE_MASK		BIT(9)
#define	CQSPI_REG_CONFIG_XIP_IMM_MASK		BIT(18)
66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
#define	CQSPI_REG_CONFIG_CHIPSELECT_LSB		10
#define	CQSPI_REG_CONFIG_BAUD_LSB		19
#define	CQSPI_REG_CONFIG_IDLE_LSB		31
#define	CQSPI_REG_CONFIG_CHIPSELECT_MASK	0xF
#define	CQSPI_REG_CONFIG_BAUD_MASK		0xF

#define	CQSPI_REG_RD_INSTR			0x04
#define	CQSPI_REG_RD_INSTR_OPCODE_LSB		0
#define	CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB	8
#define	CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB	12
#define	CQSPI_REG_RD_INSTR_TYPE_DATA_LSB	16
#define	CQSPI_REG_RD_INSTR_MODE_EN_LSB		20
#define	CQSPI_REG_RD_INSTR_DUMMY_LSB		24
#define	CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK	0x3
#define	CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK	0x3
#define	CQSPI_REG_RD_INSTR_TYPE_DATA_MASK	0x3
#define	CQSPI_REG_RD_INSTR_DUMMY_MASK		0x1F

#define	CQSPI_REG_WR_INSTR			0x08
#define	CQSPI_REG_WR_INSTR_OPCODE_LSB		0

#define	CQSPI_REG_DELAY				0x0C
#define	CQSPI_REG_DELAY_TSLCH_LSB		0
#define	CQSPI_REG_DELAY_TCHSH_LSB		8
#define	CQSPI_REG_DELAY_TSD2D_LSB		16
#define	CQSPI_REG_DELAY_TSHSL_LSB		24
#define	CQSPI_REG_DELAY_TSLCH_MASK		0xFF
#define	CQSPI_REG_DELAY_TCHSH_MASK		0xFF
#define	CQSPI_REG_DELAY_TSD2D_MASK		0xFF
#define	CQSPI_REG_DELAY_TSHSL_MASK		0xFF

#define	CQSPI_READLCAPTURE			0x10
#define	CQSPI_READLCAPTURE_BYPASS_LSB		0
#define	CQSPI_READLCAPTURE_DELAY_LSB		1
#define	CQSPI_READLCAPTURE_DELAY_MASK		0xF

#define	CQSPI_REG_SIZE				0x14
#define	CQSPI_REG_SIZE_ADDRESS_LSB		0
#define	CQSPI_REG_SIZE_PAGE_LSB			4
#define	CQSPI_REG_SIZE_BLOCK_LSB		16
#define	CQSPI_REG_SIZE_ADDRESS_MASK		0xF
#define	CQSPI_REG_SIZE_PAGE_MASK		0xFFF
#define	CQSPI_REG_SIZE_BLOCK_MASK		0x3F

#define	CQSPI_REG_SRAMPARTITION			0x18
#define	CQSPI_REG_INDIRECTTRIGGER		0x1C

#define	CQSPI_REG_REMAP				0x24
#define	CQSPI_REG_MODE_BIT			0x28

#define	CQSPI_REG_SDRAMLEVEL			0x2C
#define	CQSPI_REG_SDRAMLEVEL_RD_LSB		0
#define	CQSPI_REG_SDRAMLEVEL_WR_LSB		16
#define	CQSPI_REG_SDRAMLEVEL_RD_MASK		0xFFFF
#define	CQSPI_REG_SDRAMLEVEL_WR_MASK		0xFFFF

#define	CQSPI_REG_IRQSTATUS			0x40
#define	CQSPI_REG_IRQMASK			0x44

#define	CQSPI_REG_INDIRECTRD			0x60
126 127 128 129
#define	CQSPI_REG_INDIRECTRD_START_MASK		BIT(0)
#define	CQSPI_REG_INDIRECTRD_CANCEL_MASK	BIT(1)
#define	CQSPI_REG_INDIRECTRD_INPROGRESS_MASK	BIT(2)
#define	CQSPI_REG_INDIRECTRD_DONE_MASK		BIT(5)
130 131 132 133 134 135

#define	CQSPI_REG_INDIRECTRDWATERMARK		0x64
#define	CQSPI_REG_INDIRECTRDSTARTADDR		0x68
#define	CQSPI_REG_INDIRECTRDBYTES		0x6C

#define	CQSPI_REG_CMDCTRL			0x90
136 137
#define	CQSPI_REG_CMDCTRL_EXECUTE_MASK		BIT(0)
#define	CQSPI_REG_CMDCTRL_INPROGRESS_MASK	BIT(1)
138 139 140 141 142 143 144 145 146 147 148 149 150 151 152
#define	CQSPI_REG_CMDCTRL_DUMMY_LSB		7
#define	CQSPI_REG_CMDCTRL_WR_BYTES_LSB		12
#define	CQSPI_REG_CMDCTRL_WR_EN_LSB		15
#define	CQSPI_REG_CMDCTRL_ADD_BYTES_LSB		16
#define	CQSPI_REG_CMDCTRL_ADDR_EN_LSB		19
#define	CQSPI_REG_CMDCTRL_RD_BYTES_LSB		20
#define	CQSPI_REG_CMDCTRL_RD_EN_LSB		23
#define	CQSPI_REG_CMDCTRL_OPCODE_LSB		24
#define	CQSPI_REG_CMDCTRL_DUMMY_MASK		0x1F
#define	CQSPI_REG_CMDCTRL_WR_BYTES_MASK		0x7
#define	CQSPI_REG_CMDCTRL_ADD_BYTES_MASK	0x3
#define	CQSPI_REG_CMDCTRL_RD_BYTES_MASK		0x7
#define	CQSPI_REG_CMDCTRL_OPCODE_MASK		0xFF

#define	CQSPI_REG_INDIRECTWR			0x70
153 154 155 156
#define	CQSPI_REG_INDIRECTWR_START_MASK		BIT(0)
#define	CQSPI_REG_INDIRECTWR_CANCEL_MASK	BIT(1)
#define	CQSPI_REG_INDIRECTWR_INPROGRESS_MASK	BIT(2)
#define	CQSPI_REG_INDIRECTWR_DONE_MASK		BIT(5)
157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295

#define	CQSPI_REG_INDIRECTWRWATERMARK		0x74
#define	CQSPI_REG_INDIRECTWRSTARTADDR		0x78
#define	CQSPI_REG_INDIRECTWRBYTES		0x7C

#define	CQSPI_REG_CMDADDRESS			0x94
#define	CQSPI_REG_CMDREADDATALOWER		0xA0
#define	CQSPI_REG_CMDREADDATAUPPER		0xA4
#define	CQSPI_REG_CMDWRITEDATALOWER		0xA8
#define	CQSPI_REG_CMDWRITEDATAUPPER		0xAC

#define CQSPI_REG_IS_IDLE(base)					\
	((readl(base + CQSPI_REG_CONFIG) >>		\
		CQSPI_REG_CONFIG_IDLE_LSB) & 0x1)

#define CQSPI_CAL_DELAY(tdelay_ns, tref_ns, tsclk_ns)		\
	((((tdelay_ns) - (tsclk_ns)) / (tref_ns)))

#define CQSPI_GET_RD_SRAM_LEVEL(reg_base)			\
	(((readl(reg_base + CQSPI_REG_SDRAMLEVEL)) >>	\
	CQSPI_REG_SDRAMLEVEL_RD_LSB) & CQSPI_REG_SDRAMLEVEL_RD_MASK)

#define CQSPI_GET_WR_SRAM_LEVEL(reg_base)			\
	(((readl(reg_base + CQSPI_REG_SDRAMLEVEL)) >>	\
	CQSPI_REG_SDRAMLEVEL_WR_LSB) & CQSPI_REG_SDRAMLEVEL_WR_MASK)

static unsigned int cadence_qspi_apb_cmd2addr(const unsigned char *addr_buf,
	unsigned int addr_width)
{
	unsigned int addr;

	addr = (addr_buf[0] << 16) | (addr_buf[1] << 8) | addr_buf[2];

	if (addr_width == 4)
		addr = (addr << 8) | addr_buf[3];

	return addr;
}

void cadence_qspi_apb_controller_enable(void *reg_base)
{
	unsigned int reg;
	reg = readl(reg_base + CQSPI_REG_CONFIG);
	reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
	writel(reg, reg_base + CQSPI_REG_CONFIG);
	return;
}

void cadence_qspi_apb_controller_disable(void *reg_base)
{
	unsigned int reg;
	reg = readl(reg_base + CQSPI_REG_CONFIG);
	reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
	writel(reg, reg_base + CQSPI_REG_CONFIG);
	return;
}

/* Return 1 if idle, otherwise return 0 (busy). */
static unsigned int cadence_qspi_wait_idle(void *reg_base)
{
	unsigned int start, count = 0;
	/* timeout in unit of ms */
	unsigned int timeout = 5000;

	start = get_timer(0);
	for ( ; get_timer(start) < timeout ; ) {
		if (CQSPI_REG_IS_IDLE(reg_base))
			count++;
		else
			count = 0;
		/*
		 * Ensure the QSPI controller is in true idle state after
		 * reading back the same idle status consecutively
		 */
		if (count >= CQSPI_POLL_IDLE_RETRY)
			return 1;
	}

	/* Timeout, still in busy mode. */
	printf("QSPI: QSPI is still busy after poll for %d times.\n",
	       CQSPI_REG_RETRY);
	return 0;
}

void cadence_qspi_apb_readdata_capture(void *reg_base,
				unsigned int bypass, unsigned int delay)
{
	unsigned int reg;
	cadence_qspi_apb_controller_disable(reg_base);

	reg = readl(reg_base + CQSPI_READLCAPTURE);

	if (bypass)
		reg |= (1 << CQSPI_READLCAPTURE_BYPASS_LSB);
	else
		reg &= ~(1 << CQSPI_READLCAPTURE_BYPASS_LSB);

	reg &= ~(CQSPI_READLCAPTURE_DELAY_MASK
		<< CQSPI_READLCAPTURE_DELAY_LSB);

	reg |= ((delay & CQSPI_READLCAPTURE_DELAY_MASK)
		<< CQSPI_READLCAPTURE_DELAY_LSB);

	writel(reg, reg_base + CQSPI_READLCAPTURE);

	cadence_qspi_apb_controller_enable(reg_base);
	return;
}

void cadence_qspi_apb_config_baudrate_div(void *reg_base,
	unsigned int ref_clk_hz, unsigned int sclk_hz)
{
	unsigned int reg;
	unsigned int div;

	cadence_qspi_apb_controller_disable(reg_base);
	reg = readl(reg_base + CQSPI_REG_CONFIG);
	reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB);

	div = ref_clk_hz / sclk_hz;

	if (div > 32)
		div = 32;

	/* Check if even number. */
	if ((div & 1)) {
		div = (div / 2);
	} else {
		if (ref_clk_hz % sclk_hz)
			/* ensure generated SCLK doesn't exceed user
			specified sclk_hz */
			div = (div / 2);
		else
			div = (div / 2) - 1;
	}

	debug("%s: ref_clk %dHz sclk %dHz Div 0x%x\n", __func__,
	      ref_clk_hz, sclk_hz, div);

296 297 298 299 300
	/* ensure the baud rate doesn't exceed the max value */
	if (div > CQSPI_REG_CONFIG_BAUD_MASK)
		div = CQSPI_REG_CONFIG_BAUD_MASK;

	reg |= (div << CQSPI_REG_CONFIG_BAUD_LSB);
301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416
	writel(reg, reg_base + CQSPI_REG_CONFIG);

	cadence_qspi_apb_controller_enable(reg_base);
	return;
}

void cadence_qspi_apb_set_clk_mode(void *reg_base,
	unsigned int clk_pol, unsigned int clk_pha)
{
	unsigned int reg;

	cadence_qspi_apb_controller_disable(reg_base);
	reg = readl(reg_base + CQSPI_REG_CONFIG);
	reg &= ~(1 <<
		(CQSPI_REG_CONFIG_CLK_POL_LSB | CQSPI_REG_CONFIG_CLK_PHA_LSB));

	reg |= ((clk_pol & 0x1) << CQSPI_REG_CONFIG_CLK_POL_LSB);
	reg |= ((clk_pha & 0x1) << CQSPI_REG_CONFIG_CLK_PHA_LSB);

	writel(reg, reg_base + CQSPI_REG_CONFIG);

	cadence_qspi_apb_controller_enable(reg_base);
	return;
}

void cadence_qspi_apb_chipselect(void *reg_base,
	unsigned int chip_select, unsigned int decoder_enable)
{
	unsigned int reg;

	cadence_qspi_apb_controller_disable(reg_base);

	debug("%s : chipselect %d decode %d\n", __func__, chip_select,
	      decoder_enable);

	reg = readl(reg_base + CQSPI_REG_CONFIG);
	/* docoder */
	if (decoder_enable) {
		reg |= CQSPI_REG_CONFIG_DECODE_MASK;
	} else {
		reg &= ~CQSPI_REG_CONFIG_DECODE_MASK;
		/* Convert CS if without decoder.
		 * CS0 to 4b'1110
		 * CS1 to 4b'1101
		 * CS2 to 4b'1011
		 * CS3 to 4b'0111
		 */
		chip_select = 0xF & ~(1 << chip_select);
	}

	reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK
			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB);
	reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK)
			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB;
	writel(reg, reg_base + CQSPI_REG_CONFIG);

	cadence_qspi_apb_controller_enable(reg_base);
	return;
}

void cadence_qspi_apb_delay(void *reg_base,
	unsigned int ref_clk, unsigned int sclk_hz,
	unsigned int tshsl_ns, unsigned int tsd2d_ns,
	unsigned int tchsh_ns, unsigned int tslch_ns)
{
	unsigned int ref_clk_ns;
	unsigned int sclk_ns;
	unsigned int tshsl, tchsh, tslch, tsd2d;
	unsigned int reg;

	cadence_qspi_apb_controller_disable(reg_base);

	/* Convert to ns. */
	ref_clk_ns = (1000000000) / ref_clk;

	/* Convert to ns. */
	sclk_ns = (1000000000) / sclk_hz;

	/* Plus 1 to round up 1 clock cycle. */
	tshsl = CQSPI_CAL_DELAY(tshsl_ns, ref_clk_ns, sclk_ns) + 1;
	tchsh = CQSPI_CAL_DELAY(tchsh_ns, ref_clk_ns, sclk_ns) + 1;
	tslch = CQSPI_CAL_DELAY(tslch_ns, ref_clk_ns, sclk_ns) + 1;
	tsd2d = CQSPI_CAL_DELAY(tsd2d_ns, ref_clk_ns, sclk_ns) + 1;

	reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
			<< CQSPI_REG_DELAY_TSHSL_LSB);
	reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
			<< CQSPI_REG_DELAY_TCHSH_LSB);
	reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
			<< CQSPI_REG_DELAY_TSLCH_LSB);
	reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
			<< CQSPI_REG_DELAY_TSD2D_LSB);
	writel(reg, reg_base + CQSPI_REG_DELAY);

	cadence_qspi_apb_controller_enable(reg_base);
	return;
}

void cadence_qspi_apb_controller_init(struct cadence_spi_platdata *plat)
{
	unsigned reg;

	cadence_qspi_apb_controller_disable(plat->regbase);

	/* Configure the device size and address bytes */
	reg = readl(plat->regbase + CQSPI_REG_SIZE);
	/* Clear the previous value */
	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
	reg |= (plat->page_size << CQSPI_REG_SIZE_PAGE_LSB);
	reg |= (plat->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
	writel(reg, plat->regbase + CQSPI_REG_SIZE);

	/* Configure the remap address register, no remap */
	writel(0, plat->regbase + CQSPI_REG_REMAP);

417
	/* Indirect mode configurations */
418
	writel((plat->sram_size/2), plat->regbase + CQSPI_REG_SRAMPARTITION);
419

420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554
	/* Disable all interrupts */
	writel(0, plat->regbase + CQSPI_REG_IRQMASK);

	cadence_qspi_apb_controller_enable(plat->regbase);
	return;
}

static int cadence_qspi_apb_exec_flash_cmd(void *reg_base,
	unsigned int reg)
{
	unsigned int retry = CQSPI_REG_RETRY;

	/* Write the CMDCTRL without start execution. */
	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
	/* Start execute */
	reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK;
	writel(reg, reg_base + CQSPI_REG_CMDCTRL);

	while (retry--) {
		reg = readl(reg_base + CQSPI_REG_CMDCTRL);
		if ((reg & CQSPI_REG_CMDCTRL_INPROGRESS_MASK) == 0)
			break;
		udelay(1);
	}

	if (!retry) {
		printf("QSPI: flash command execution timeout\n");
		return -EIO;
	}

	/* Polling QSPI idle status. */
	if (!cadence_qspi_wait_idle(reg_base))
		return -EIO;

	return 0;
}

/* For command RDID, RDSR. */
int cadence_qspi_apb_command_read(void *reg_base,
	unsigned int cmdlen, const u8 *cmdbuf, unsigned int rxlen,
	u8 *rxbuf)
{
	unsigned int reg;
	unsigned int read_len;
	int status;

	if (!cmdlen || rxlen > CQSPI_STIG_DATA_LEN_MAX || rxbuf == NULL) {
		printf("QSPI: Invalid input arguments cmdlen %d rxlen %d\n",
		       cmdlen, rxlen);
		return -EINVAL;
	}

	reg = cmdbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;

	reg |= (0x1 << CQSPI_REG_CMDCTRL_RD_EN_LSB);

	/* 0 means 1 byte. */
	reg |= (((rxlen - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK)
		<< CQSPI_REG_CMDCTRL_RD_BYTES_LSB);
	status = cadence_qspi_apb_exec_flash_cmd(reg_base, reg);
	if (status != 0)
		return status;

	reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER);

	/* Put the read value into rx_buf */
	read_len = (rxlen > 4) ? 4 : rxlen;
	memcpy(rxbuf, &reg, read_len);
	rxbuf += read_len;

	if (rxlen > 4) {
		reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER);

		read_len = rxlen - read_len;
		memcpy(rxbuf, &reg, read_len);
	}
	return 0;
}

/* For commands: WRSR, WREN, WRDI, CHIP_ERASE, BE, etc. */
int cadence_qspi_apb_command_write(void *reg_base, unsigned int cmdlen,
	const u8 *cmdbuf, unsigned int txlen,  const u8 *txbuf)
{
	unsigned int reg = 0;
	unsigned int addr_value;
	unsigned int wr_data;
	unsigned int wr_len;

	if (!cmdlen || cmdlen > 5 || txlen > 8 || cmdbuf == NULL) {
		printf("QSPI: Invalid input arguments cmdlen %d txlen %d\n",
		       cmdlen, txlen);
		return -EINVAL;
	}

	reg |= cmdbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;

	if (cmdlen == 4 || cmdlen == 5) {
		/* Command with address */
		reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
		/* Number of bytes to write. */
		reg |= ((cmdlen - 2) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
		/* Get address */
		addr_value = cadence_qspi_apb_cmd2addr(&cmdbuf[1],
			cmdlen >= 5 ? 4 : 3);

		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
	}

	if (txlen) {
		/* writing data = yes */
		reg |= (0x1 << CQSPI_REG_CMDCTRL_WR_EN_LSB);
		reg |= ((txlen - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
			<< CQSPI_REG_CMDCTRL_WR_BYTES_LSB;

		wr_len = txlen > 4 ? 4 : txlen;
		memcpy(&wr_data, txbuf, wr_len);
		writel(wr_data, reg_base +
			CQSPI_REG_CMDWRITEDATALOWER);

		if (txlen > 4) {
			txbuf += wr_len;
			wr_len = txlen - wr_len;
			memcpy(&wr_data, txbuf, wr_len);
			writel(wr_data, reg_base +
				CQSPI_REG_CMDWRITEDATAUPPER);
		}
	}

	/* Execute the command */
	return cadence_qspi_apb_exec_flash_cmd(reg_base, reg);
}

/* Opcode + Address (3/4 bytes) + dummy bytes (0-4 bytes) */
int cadence_qspi_apb_indirect_read_setup(struct cadence_spi_platdata *plat,
555
	unsigned int cmdlen, unsigned int rx_width, const u8 *cmdbuf)
556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578
{
	unsigned int reg;
	unsigned int rd_reg;
	unsigned int addr_value;
	unsigned int dummy_clk;
	unsigned int dummy_bytes;
	unsigned int addr_bytes;

	/*
	 * Identify addr_byte. All NOR flash device drivers are using fast read
	 * which always expecting 1 dummy byte, 1 cmd byte and 3/4 addr byte.
	 * With that, the length is in value of 5 or 6. Only FRAM chip from
	 * ramtron using normal read (which won't need dummy byte).
	 * Unlikely NOR flash using normal read due to performance issue.
	 */
	if (cmdlen >= 5)
		/* to cater fast read where cmd + addr + dummy */
		addr_bytes = cmdlen - 2;
	else
		/* for normal read (only ramtron as of now) */
		addr_bytes = cmdlen - 1;

	/* Setup the indirect trigger address */
579
	writel((u32)plat->ahbbase,
580 581 582 583 584
	       plat->regbase + CQSPI_REG_INDIRECTTRIGGER);

	/* Configure the opcode */
	rd_reg = cmdbuf[0] << CQSPI_REG_RD_INSTR_OPCODE_LSB;

585 586 587
	if (rx_width & SPI_RX_QUAD)
		/* Instruction and address at DQ0, data at DQ0-3. */
		rd_reg |= CQSPI_INST_TYPE_QUAD << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625

	/* Get address */
	addr_value = cadence_qspi_apb_cmd2addr(&cmdbuf[1], addr_bytes);
	writel(addr_value, plat->regbase + CQSPI_REG_INDIRECTRDSTARTADDR);

	/* The remaining lenght is dummy bytes. */
	dummy_bytes = cmdlen - addr_bytes - 1;
	if (dummy_bytes) {
		if (dummy_bytes > CQSPI_DUMMY_BYTES_MAX)
			dummy_bytes = CQSPI_DUMMY_BYTES_MAX;

		rd_reg |= (1 << CQSPI_REG_RD_INSTR_MODE_EN_LSB);
#if defined(CONFIG_SPL_SPI_XIP) && defined(CONFIG_SPL_BUILD)
		writel(0x0, plat->regbase + CQSPI_REG_MODE_BIT);
#else
		writel(0xFF, plat->regbase + CQSPI_REG_MODE_BIT);
#endif

		/* Convert to clock cycles. */
		dummy_clk = dummy_bytes * CQSPI_DUMMY_CLKS_PER_BYTE;
		/* Need to minus the mode byte (8 clocks). */
		dummy_clk -= CQSPI_DUMMY_CLKS_PER_BYTE;

		if (dummy_clk)
			rd_reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
				<< CQSPI_REG_RD_INSTR_DUMMY_LSB;
	}

	writel(rd_reg, plat->regbase + CQSPI_REG_RD_INSTR);

	/* set device size */
	reg = readl(plat->regbase + CQSPI_REG_SIZE);
	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
	reg |= (addr_bytes - 1);
	writel(reg, plat->regbase + CQSPI_REG_SIZE);
	return 0;
}

626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647
static u32 cadence_qspi_get_rd_sram_level(struct cadence_spi_platdata *plat)
{
	u32 reg = readl(plat->regbase + CQSPI_REG_SDRAMLEVEL);
	reg >>= CQSPI_REG_SDRAMLEVEL_RD_LSB;
	return reg & CQSPI_REG_SDRAMLEVEL_RD_MASK;
}

static int cadence_qspi_wait_for_data(struct cadence_spi_platdata *plat)
{
	unsigned int timeout = 10000;
	u32 reg;

	while (timeout--) {
		reg = cadence_qspi_get_rd_sram_level(plat);
		if (reg)
			return reg;
		udelay(1);
	}

	return -ETIMEDOUT;
}

648
int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat,
649
	unsigned int n_rx, u8 *rxbuf)
650
{
651 652 653
	unsigned int remaining = n_rx;
	unsigned int bytes_to_read = 0;
	int ret;
654

655
	writel(n_rx, plat->regbase + CQSPI_REG_INDIRECTRDBYTES);
656 657 658 659 660

	/* Start the indirect read transfer */
	writel(CQSPI_REG_INDIRECTRD_START_MASK,
	       plat->regbase + CQSPI_REG_INDIRECTRD);

661 662 663 664 665 666
	while (remaining > 0) {
		ret = cadence_qspi_wait_for_data(plat);
		if (ret < 0) {
			printf("Indirect write timed out (%i)\n", ret);
			goto failrd;
		}
667

668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689
		bytes_to_read = ret;

		while (bytes_to_read != 0) {
			bytes_to_read *= CQSPI_FIFO_WIDTH;
			bytes_to_read = bytes_to_read > remaining ?
					remaining : bytes_to_read;
			/* Handle non-4-byte aligned access to avoid data abort. */
			if (((uintptr_t)rxbuf % 4) || (bytes_to_read % 4))
				readsb(plat->ahbbase, rxbuf, bytes_to_read);
			else
				readsl(plat->ahbbase, rxbuf, bytes_to_read >> 2);
			rxbuf += bytes_to_read;
			remaining -= bytes_to_read;
			bytes_to_read = cadence_qspi_get_rd_sram_level(plat);
		}
	}

	/* Check indirect done status */
	ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_INDIRECTRD,
			   CQSPI_REG_INDIRECTRD_DONE_MASK, 1, 10, 0);
	if (ret) {
		printf("Indirect read completion error (%i)\n", ret);
690 691 692 693 694 695
		goto failrd;
	}

	/* Clear indirect completion status */
	writel(CQSPI_REG_INDIRECTRD_DONE_MASK,
	       plat->regbase + CQSPI_REG_INDIRECTRD);
696

697 698 699 700 701 702
	return 0;

failrd:
	/* Cancel the indirect read */
	writel(CQSPI_REG_INDIRECTRD_CANCEL_MASK,
	       plat->regbase + CQSPI_REG_INDIRECTRD);
703
	return ret;
704 705 706 707 708 709 710 711 712 713 714 715 716 717 718
}

/* Opcode + Address (3/4 bytes) */
int cadence_qspi_apb_indirect_write_setup(struct cadence_spi_platdata *plat,
	unsigned int cmdlen, const u8 *cmdbuf)
{
	unsigned int reg;
	unsigned int addr_bytes = cmdlen > 4 ? 4 : 3;

	if (cmdlen < 4 || cmdbuf == NULL) {
		printf("QSPI: iInvalid input argument, len %d cmdbuf 0x%08x\n",
		       cmdlen, (unsigned int)cmdbuf);
		return -EINVAL;
	}
	/* Setup the indirect trigger address */
719
	writel((u32)plat->ahbbase,
720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737
	       plat->regbase + CQSPI_REG_INDIRECTTRIGGER);

	/* Configure the opcode */
	reg = cmdbuf[0] << CQSPI_REG_WR_INSTR_OPCODE_LSB;
	writel(reg, plat->regbase + CQSPI_REG_WR_INSTR);

	/* Setup write address. */
	reg = cadence_qspi_apb_cmd2addr(&cmdbuf[1], addr_bytes);
	writel(reg, plat->regbase + CQSPI_REG_INDIRECTWRSTARTADDR);

	reg = readl(plat->regbase + CQSPI_REG_SIZE);
	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
	reg |= (addr_bytes - 1);
	writel(reg, plat->regbase + CQSPI_REG_SIZE);
	return 0;
}

int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
738
	unsigned int n_tx, const u8 *txbuf)
739
{
740 741 742 743
	unsigned int page_size = plat->page_size;
	unsigned int remaining = n_tx;
	unsigned int write_bytes;
	int ret;
744 745

	/* Configure the indirect read transfer bytes */
746
	writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES);
747 748 749 750 751

	/* Start the indirect write transfer */
	writel(CQSPI_REG_INDIRECTWR_START_MASK,
	       plat->regbase + CQSPI_REG_INDIRECTWR);

752 753 754 755 756 757 758 759 760 761 762 763 764 765 766
	while (remaining > 0) {
		write_bytes = remaining > page_size ? page_size : remaining;
		/* Handle non-4-byte aligned access to avoid data abort. */
		if (((uintptr_t)txbuf % 4) || (write_bytes % 4))
			writesb(plat->ahbbase, txbuf, write_bytes);
		else
			writesl(plat->ahbbase, txbuf, write_bytes >> 2);

		ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_SDRAMLEVEL,
				   CQSPI_REG_SDRAMLEVEL_WR_MASK <<
				   CQSPI_REG_SDRAMLEVEL_WR_LSB, 0, 10, 0);
		if (ret) {
			printf("Indirect write timed out (%i)\n", ret);
			goto failwr;
		}
767

768 769
		txbuf += write_bytes;
		remaining -= write_bytes;
770 771
	}

772 773 774 775 776
	/* Check indirect done status */
	ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_INDIRECTWR,
			   CQSPI_REG_INDIRECTWR_DONE_MASK, 1, 10, 0);
	if (ret) {
		printf("Indirect write completion error (%i)\n", ret);
777 778 779 780 781 782 783 784 785 786 787 788
		goto failwr;
	}

	/* Clear indirect completion status */
	writel(CQSPI_REG_INDIRECTWR_DONE_MASK,
	       plat->regbase + CQSPI_REG_INDIRECTWR);
	return 0;

failwr:
	/* Cancel the indirect write */
	writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
	       plat->regbase + CQSPI_REG_INDIRECTWR);
789
	return ret;
790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810
}

void cadence_qspi_apb_enter_xip(void *reg_base, char xip_dummy)
{
	unsigned int reg;

	/* enter XiP mode immediately and enable direct mode */
	reg = readl(reg_base + CQSPI_REG_CONFIG);
	reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
	reg |= CQSPI_REG_CONFIG_DIRECT_MASK;
	reg |= CQSPI_REG_CONFIG_XIP_IMM_MASK;
	writel(reg, reg_base + CQSPI_REG_CONFIG);

	/* keep the XiP mode */
	writel(xip_dummy, reg_base + CQSPI_REG_MODE_BIT);

	/* Enable mode bit at devrd */
	reg = readl(reg_base + CQSPI_REG_RD_INSTR);
	reg |= (1 << CQSPI_REG_RD_INSTR_MODE_EN_LSB);
	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
}