Commit 0d8382ae authored by Jelle van der Waa's avatar Jelle van der Waa Committed by Hans de Goede

sunxi: power: add support for sy8106a driver

SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.

This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: default avatarJelle van der Waa <jelle@vdwaa.nl>
Tested-by: default avatarSiarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: default avatarSiarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
parent 595af9db
......@@ -372,11 +372,14 @@ config I2C3_ENABLE
See I2C0_ENABLE help text.
endif
if SUNXI_GEN_SUN6I
config R_I2C_ENABLE
bool "Enable the PRCM I2C/TWI controller"
default n
# This is used for the pmic on H3
default y if SY8106A_POWER
---help---
Set this to y to enable the I2C controller which is part of the PRCM.
endif
if MACH_SUN7I
config I2C4_ENABLE
......
......@@ -25,6 +25,7 @@
#include <asm/io.h>
#include <nand.h>
#include <net.h>
#include <sy8106a.h>
#if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
/* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */
......@@ -436,6 +437,10 @@ void sunxi_board_init(void)
int power_failed = 0;
unsigned long ramsize;
#ifdef CONFIG_SY8106A_POWER
power_failed = sy8106a_set_vout1(CONFIG_SY8106A_VOUT1_VOLT);
#endif
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
power_failed = axp_init();
......
......@@ -12,4 +12,4 @@ CONFIG_SPL=y
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_CMD_GPIO=y
CONFIG_R_I2C_ENABLE=y
CONFIG_SY8106A_POWER=y
......@@ -12,3 +12,4 @@ CONFIG_SPL=y
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_CMD_GPIO=y
CONFIG_SY8106A_POWER=y
......@@ -48,6 +48,13 @@ config AXP818_POWER
Say y here to enable support for the axp818 pmic found on
A83T dev board.
config SY8106A_POWER
boolean "SY8106A pmic support"
depends on MACH_SUN8I_H3
---help---
Select this to enable support for the SY8106A pmic found on some
H3 boards.
endchoice
config AXP_DCDC1_VOLT
......@@ -232,4 +239,13 @@ config AXP_ELDO3_VOLT
1.2V for the SSD2828 chip (converter of parallel LCD interface
into MIPI DSI).
config SY8106A_VOUT1_VOLT
int "SY8106A pmic VOUT1 voltage"
depends on SY8106A_POWER
default 1200
---help---
Set the voltage (mV) to program the SY8106A pmic VOUT1. This
is typically used to power the VDD-CPU and should be 1200mV.
Values can range from 680mV till 1950mV.
endmenu
......@@ -12,6 +12,7 @@ obj-$(CONFIG_AXP221_POWER) += axp221.o
obj-$(CONFIG_AXP818_POWER) += axp818.o
obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
obj-$(CONFIG_FTPMU010_POWER) += ftpmu010.o
obj-$(CONFIG_SY8106A_POWER) += sy8106a.o
obj-$(CONFIG_TPS6586X_POWER) += tps6586x.o
obj-$(CONFIG_TWL4030_POWER) += twl4030.o
obj-$(CONFIG_TWL6030_POWER) += twl6030.o
......
/*
* (C) Copyright 2016
* Jelle van der Waa <jelle@vdwaa.nl>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <sy8106a.h>
#define SY8106A_I2C_ADDR 0x65
#define SY8106A_VOUT1_SEL 1
#define SY8106A_VOUT1_SEL_ENABLE (1 << 7)
static u8 sy8106a_mvolt_to_cfg(int mvolt, int min, int max, int div)
{
if (mvolt < min)
mvolt = min;
else if (mvolt > max)
mvolt = max;
return (mvolt - min) / div;
}
int sy8106a_set_vout1(unsigned int mvolt)
{
u8 data = sy8106a_mvolt_to_cfg(mvolt, 680, 1950, 10) | SY8106A_VOUT1_SEL_ENABLE;
return i2c_write(SY8106A_I2C_ADDR, SY8106A_VOUT1_SEL, 1, &data, 1);
}
......@@ -206,7 +206,8 @@
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
/* I2C */
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
defined CONFIG_SY8106A_POWER
#define CONFIG_SPL_I2C_SUPPORT
#endif
......@@ -240,7 +241,8 @@ extern int soft_i2c_gpio_scl;
/* PMU */
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER || \
defined CONFIG_SY8106A_POWER
#define CONFIG_SPL_POWER_SUPPORT
#endif
......
/*
* (C) Copyright 2016
* Jelle van der Waa <jelle@vdwaa.nl>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SY8106A_PMIC_H_
int sy8106a_set_vout1(unsigned int mvolt);
#endif
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment