Commit 23e1acaf authored by Shaohui Xie's avatar Shaohui Xie Committed by York Sun

net/fm: fix MDIO controller base on FMAN2

MDIO controller base on FMAN2 was defined as CONFIG_SYS_FSL_FM2_ADDR
plus offset, but CONFIG_SYS_FSL_FM2_ADDR only defined when there are two
FMANs, so we should only define MDIO controller base on FMAN2 when there
is FMAN2.
Signed-off-by: default avatarShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: default avatarMingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: default avatarGong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: default avatarYork Sun <yorksun@freescale.com>
parent bc24611c
......@@ -45,8 +45,10 @@ enum fm_eth_type {
#ifdef CONFIG_SYS_FMAN_V3
#define CONFIG_SYS_FM1_DTSEC_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xfc000)
#define CONFIG_SYS_FM1_TGEC_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xfd000)
#if (CONFIG_SYS_NUM_FMAN == 2)
#define CONFIG_SYS_FM2_DTSEC_MDIO_ADDR (CONFIG_SYS_FSL_FM2_ADDR + 0xfc000)
#define CONFIG_SYS_FM2_TGEC_MDIO_ADDR (CONFIG_SYS_FSL_FM2_ADDR + 0xfd000)
#endif
#else
#define CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xe1120)
#define CONFIG_SYS_FM1_TGEC_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xf1000)
......@@ -89,6 +91,7 @@ enum fm_eth_type {
offsetof(struct ccsr_fman, memac[n-1]),\
}
#else
#if (CONFIG_SYS_NUM_FMAN == 2)
#define FM_TGEC_INFO_INITIALIZER(idx, n) \
{ \
FM_ETH_INFO_INITIALIZER(idx, CONFIG_SYS_FM2_TGEC_MDIO_ADDR) \
......@@ -101,6 +104,20 @@ enum fm_eth_type {
.compat_offset = CONFIG_SYS_FSL_FM##idx##_OFFSET + \
offsetof(struct ccsr_fman, memac[n-1+8]),\
}
#else
#define FM_TGEC_INFO_INITIALIZER(idx, n) \
{ \
FM_ETH_INFO_INITIALIZER(idx, CONFIG_SYS_FM1_TGEC_MDIO_ADDR) \
.index = idx, \
.num = n - 1, \
.type = FM_ETH_10G_E, \
.port = FM##idx##_10GEC##n, \
.rx_port_id = RX_PORT_10G_BASE + n - 1, \
.tx_port_id = TX_PORT_10G_BASE + n - 1, \
.compat_offset = CONFIG_SYS_FSL_FM##idx##_OFFSET + \
offsetof(struct ccsr_fman, memac[n-1+8]),\
}
#endif
#endif
#if (CONFIG_SYS_NUM_FM1_10GEC >= 3)
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment