Commit 45219c46 authored by wdenk's avatar wdenk

Patch by Mathijs Haarman, 08 May 2003:

Add lan91c96 driver (tested on Lubbock and custom PXA250 board only)
parent f7de16ae
......@@ -2,6 +2,9 @@
Changes since U-Boot 0.3.1:
======================================================================
* Patch by Mathijs Haarman, 08 May 2003:
Add lan91c96 driver (tested on Lubbock and custom PXA250 board only)
* Fix problem with usage of "true" (undefined in current versions of bfd.h)
* Add support for Promess ATC board
......
......@@ -67,7 +67,7 @@ LIST_824x=" \
#########################################################################
LIST_8260=" \
ATC cogent_mpc8260 CPU86 ep8260 \
atc cogent_mpc8260 CPU86 ep8260 \
gw8260 hymod IPHASE4539 MPC8260ADS \
MPC8266ADS PM826 ppmc8260 RPXsuper \
rsdproto sacsng sbc8260 SCM \
......
......@@ -695,6 +695,18 @@ The following options need to be configured:
CONFIG_NS8382X
Support for National dp8382[01] gigabit chips.
- NETWORK Support (other):
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
CONFIG_LAN91C96_BASE
Define this to hold the physical address
of the LAN91C96's I/O space
CONFIG_LAN91C96_USE_32_BIT
Define this to enable 32 bit addressing
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405); define
......
......@@ -7,22 +7,32 @@ Installation Instructions:
------
|x |
| x|
|x |
| X|
|x |
| X|
------
Put the s3 switch into the following position:
1 0
1 0
------
| x |
| x |
| x|
| x|
------
Put the s4 switch into the following position:
1 0
------
|x |
|x |
|x |
|x |
|x |
|x |
| x|
| x|
|x |
|x |
------
2. Connect to the serial console and to the BDI. Power on. On the
......@@ -54,8 +64,8 @@ Installation Instructions:
------
| x|
| x|
|x |
| X|
|x |
| X|
------
Power on. U-Boot should come up.
......
......@@ -30,7 +30,7 @@ LIB = libdrivers.a
OBJS = 3c589.o 5701rls.o at91rm9200_ether.o \
bcm570x.o bcm570x_autoneg.o \
cfb_console.o cs8900.o ct69000.o dc2114x.o \
eepro100.o i8042.o inca-ip_sw.o \
eepro100.o i8042.o inca-ip_sw.o lan91c96.o\
natsemi.o ns16550.o ns8382x.o ns87308.o \
pci.o pci_auto.o pci_indirect.o \
pcnet.o plb2800_eth.o \
......
This diff is collapsed.
This diff is collapsed.
......@@ -53,6 +53,8 @@
/*
* Hardware drivers
*/
#define CONFIG_DRIVER_LAN91C96
#define CONFIG_LAN91C96_BASE 0x0C000000
/*
* select serial console configuration
......@@ -64,7 +66,7 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
......
......@@ -42,6 +42,9 @@ const char version_string[] =
extern void cs8900_get_enetaddr (uchar * addr);
#endif
#ifdef CONFIG_DRIVER_LAN91C96
#include "../drivers/lan91c96.h"
#endif
/*
* Begin and End of memory area for malloc(), and current "brk"
*/
......@@ -275,6 +278,13 @@ void start_armboot (void)
cs8900_get_enetaddr (gd->bd->bi_enetaddr);
#endif
#ifdef CONFIG_DRIVER_LAN91C96
if (getenv ("ethaddr")) {
smc_set_mac_addr(gd->bd->bi_enetaddr);
}
/* eth_hw_init(); */
#endif /* CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
if ((s = getenv ("loadaddr")) != NULL) {
load_addr = simple_strtoul (s, NULL, 16);
......
......@@ -50,10 +50,10 @@
#include <watchdog.h>
#include <i2c.h>
static int sysmon_temp_invalid = 0;
#if CONFIG_POST & CFG_POST_SYSMON
static int sysmon_temp_invalid = 0;
/* #define DEBUG */
#define RELOC(x) if (x != NULL) x = (void *) ((ulong) (x) + gd->reloc_off)
......
......@@ -73,7 +73,9 @@ static struct {
static char *ctlr_name[2] = { "SMC", "SCC" };
static int used_by_uart[2] = { -1, -1 };
#if defined(SCC_ENET)
static int used_by_ether[2] = { -1, -1 };
#endif
static int proff_smc[] = { PROFF_SMC1, PROFF_SMC2 };
static int proff_scc[] =
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment