Commit 4d13b1b7 authored by Masahiro Yamada's avatar Masahiro Yamada

ARM: UniPhier: fix typos in comments

Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
parent def3feb8
......@@ -25,8 +25,8 @@ ENTRY(lowlevel_init)
* First we need to turn on MMU and Dcache again to get back
* data access to L2.
*/
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
#ifdef CONFIG_DEBUG_LL
......@@ -41,7 +41,7 @@ ENTRY(lowlevel_init)
ldr r3, =init_page_table @ page table must be 16KB aligned
/* Disable MMU and Dcache before switching Page Table */
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
bic r0, r0, #(CR_C | CR_M) @ disable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
......@@ -55,7 +55,7 @@ ENTRY(lowlevel_init)
* bit[7] EXCL (Exclusive cache bit)
* bit[6] SMP
* bit[3] Write full line of zeros mode
* bit[2] L1 Prefetch enable
* bit[2] L1 prefetch enable
* bit[1] L2 prefetch enable
* bit[0] FW (Cache and TLB maintenance broadcast)
*/
......@@ -81,7 +81,7 @@ primary_cpu:
ldr r0, =_start @ entry for the secondary CPU
str r0, [r1]
ldr r0, [r1] @ make sure str is complete before sev
sev @ kick the sedoncary CPU
sev @ kick the secondary CPU
mrc p15, 4, r1, c15, c0, 0 @ Configuration Base Address Register
bfc r1, #0, #13 @ clear bit 12-0
mov r0, #-1
......@@ -118,7 +118,7 @@ ENTRY(enable_mmu)
* TLBs was already invalidated in "../start.S"
* So, we don't need to invalidate it here.
*/
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
orr r0, r0, #(CR_C | CR_M) @ MMU and Dcache enable
mcr p15, 0, r0, c1, c0, 0
......@@ -155,7 +155,7 @@ ENTRY(setup_init_ram)
ldr r1, = SSCOPPQSEF
ldr r0, [r1]
cmp r0, #0 @ check if the command is successfully set
bne 0b @ try again if an error occurres
bne 0b @ try again if an error occurs
ldr r1, = SSCOLPQS
1:
......
/*
* Copyright (C) 2012-2014 Panasonic Corporation
* Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Copyright (C) 2012-2015 Panasonic Corporation
* Copyright (C) 2015 Socionext Inc.
* Author: Masahiro Yamada <yamada.masahiro@socionext.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
......@@ -94,7 +95,7 @@ void support_card_init(void)
/*
* After power on, we need to keep the LAN controller in reset state
* for a while. (200 usec)
* Fortunatelly, enough wait time is already inserted in pll_init()
* Fortunately, enough wait time is already inserted in pll_init()
* function. So we do not have to wait here.
*/
support_card_reset_deassert();
......@@ -213,11 +214,11 @@ static void detect_num_flash_banks(void)
debug("number of flash banks: %d\n", cfi_flash_num_flash_banks);
}
#else /* ONFIG_SYS_NO_FLASH */
#else /* CONFIG_SYS_NO_FLASH */
void detect_num_flash_banks(void)
{
};
#endif /* ONFIG_SYS_NO_FLASH */
#endif /* CONFIG_SYS_NO_FLASH */
void support_card_late_init(void)
{
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment