Commit 57897c13 authored by Vignesh R's avatar Vignesh R Committed by Jagan Teki

spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible

According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.

So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.

[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: default avatarVignesh R <vigneshr@ti.com>
Reviewed-by: default avatarMarek Vasut <marex@denx.de>
Reviewed-by: default avatarJagan Teki <jagan@openedev.com>
parent 87f5f541
......@@ -30,6 +30,7 @@
#include <linux/errno.h>
#include <wait_bit.h>
#include <spi.h>
#include <bouncebuf.h>
#include "cadence_qspi.h"
#define CQSPI_REG_POLL_US 1 /* 1us */
......@@ -724,6 +725,17 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
unsigned int remaining = n_tx;
unsigned int write_bytes;
int ret;
struct bounce_buffer bb;
u8 *bb_txbuf;
/*
* Handle non-4-byte aligned accesses via bounce buffer to
* avoid data abort.
*/
ret = bounce_buffer_start(&bb, (void *)txbuf, n_tx, GEN_BB_READ);
if (ret)
return ret;
bb_txbuf = bb.bounce_buffer;
/* Configure the indirect read transfer bytes */
writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES);
......@@ -734,11 +746,11 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
while (remaining > 0) {
write_bytes = remaining > page_size ? page_size : remaining;
/* Handle non-4-byte aligned access to avoid data abort. */
if (((uintptr_t)txbuf % 4) || (write_bytes % 4))
writesb(plat->ahbbase, txbuf, write_bytes);
else
writesl(plat->ahbbase, txbuf, write_bytes >> 2);
writesl(plat->ahbbase, bb_txbuf, write_bytes >> 2);
if (write_bytes % 4)
writesb(plat->ahbbase,
bb_txbuf + rounddown(write_bytes, 4),
write_bytes % 4);
ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_SDRAMLEVEL,
CQSPI_REG_SDRAMLEVEL_WR_MASK <<
......@@ -748,7 +760,7 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
goto failwr;
}
txbuf += write_bytes;
bb_txbuf += write_bytes;
remaining -= write_bytes;
}
......@@ -759,6 +771,7 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
printf("Indirect write completion error (%i)\n", ret);
goto failwr;
}
bounce_buffer_stop(&bb);
/* Clear indirect completion status */
writel(CQSPI_REG_INDIRECTWR_DONE,
......@@ -769,6 +782,7 @@ failwr:
/* Cancel the indirect write */
writel(CQSPI_REG_INDIRECTWR_CANCEL,
plat->regbase + CQSPI_REG_INDIRECTWR);
bounce_buffer_stop(&bb);
return ret;
}
......
......@@ -77,6 +77,7 @@
#define CONFIG_CADENCE_QSPI
#define CONFIG_CQSPI_REF_CLK 384000000
#define CONFIG_CQSPI_DECODER 0x0
#define CONFIG_BOUNCE_BUFFER
#endif
#endif /* __CONFIG_K2G_EVM_H */
......@@ -207,6 +207,7 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
#endif
#define CONFIG_CQSPI_DECODER 0
#define CONFIG_BOUNCE_BUFFER
/*
* Designware SPI support
......
......@@ -74,6 +74,7 @@
#ifdef CONFIG_OF_CONTROL /* QSPI is controlled via DT */
#define CONFIG_CQSPI_DECODER 0
#define CONFIG_CQSPI_REF_CLK ((30/4)/2)*1000*1000
#define CONFIG_BOUNCE_BUFFER
#endif
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment