Commit 602ad3b3 authored by Jon Loeliger's avatar Jon Loeliger Committed by Wolfgang Denk

README: Rewrite command line config to use CONFIG_CMD_* names.

Signed-off-by: default avatarJon Loeliger <jdl@freescale.com>
parent 72a074ce
......@@ -541,7 +541,7 @@ The following options need to be configured:
CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
CONFIG_CONSOLE_TIME display time/date info in
upper right corner
(requires CFG_CMD_DATE)
(requires CONFIG_CMD_DATE)
CONFIG_VIDEO_LOGO display Linux logo in
upper left corner
CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
......@@ -645,103 +645,96 @@ The following options need to be configured:
time on others. This setting #define's the initial
value of the "loads_echo" environment variable.
- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
CONFIG_KGDB_BAUDRATE
Select one of the baudrates listed in
CFG_BAUDRATE_TABLE, see below.
- Monitor Functions:
CONFIG_COMMANDS
Most monitor functions can be selected (or
de-selected) by adjusting the definition of
CONFIG_COMMANDS; to select individual functions,
#define CONFIG_COMMANDS by "OR"ing any of the
following values:
#define enables commands:
-------------------------
CFG_CMD_ASKENV * ask for env variable
CFG_CMD_AUTOSCRIPT Autoscript Support
CFG_CMD_BDI bdinfo
CFG_CMD_BEDBUG * Include BedBug Debugger
CFG_CMD_BMP * BMP support
CFG_CMD_BSP * Board specific commands
CFG_CMD_BOOTD bootd
CFG_CMD_CACHE * icache, dcache
CFG_CMD_CONSOLE coninfo
CFG_CMD_DATE * support for RTC, date/time...
CFG_CMD_DHCP * DHCP support
CFG_CMD_DIAG * Diagnostics
CFG_CMD_DOC * Disk-On-Chip Support
CFG_CMD_DTT * Digital Therm and Thermostat
CFG_CMD_ECHO echo arguments
CFG_CMD_EEPROM * EEPROM read/write support
CFG_CMD_ELF * bootelf, bootvx
CFG_CMD_ENV saveenv
CFG_CMD_FDC * Floppy Disk Support
CFG_CMD_FAT * FAT partition support
CFG_CMD_FDOS * Dos diskette Support
CFG_CMD_FLASH flinfo, erase, protect
CFG_CMD_FPGA FPGA device initialization support
CFG_CMD_HWFLOW * RTS/CTS hw flow control
CFG_CMD_I2C * I2C serial bus support
CFG_CMD_IDE * IDE harddisk support
CFG_CMD_IMI iminfo
CFG_CMD_IMLS List all found images
CFG_CMD_IMMAP * IMMR dump support
CFG_CMD_IRQ * irqinfo
CFG_CMD_ITEST Integer/string test of 2 values
CFG_CMD_JFFS2 * JFFS2 Support
CFG_CMD_KGDB * kgdb
CFG_CMD_LOADB loadb
CFG_CMD_LOADS loads
CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw, mtest
CFG_CMD_MISC Misc functions like sleep etc
CFG_CMD_MMC * MMC memory mapped support
CFG_CMD_MII * MII utility commands
CFG_CMD_NAND * NAND support
CFG_CMD_NET bootp, tftpboot, rarpboot
CFG_CMD_PCI * pciinfo
CFG_CMD_PCMCIA * PCMCIA support
CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
CFG_CMD_PORTIO * Port I/O
CFG_CMD_REGINFO * Register dump
CFG_CMD_RUN run command in env variable
CFG_CMD_SAVES * save S record dump
CFG_CMD_SCSI * SCSI Support
CFG_CMD_SDRAM * print SDRAM configuration information
(requires CFG_CMD_I2C)
CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
CFG_CMD_SPI * SPI serial bus support
CFG_CMD_USB * USB support
CFG_CMD_VFD * VFD support (TRAB)
CFG_CMD_BSP * Board SPecific functions
CFG_CMD_CDP * Cisco Discover Protocol support
CFG_CMD_FSL * Microblaze FSL support
-----------------------------------------------
CFG_CMD_ALL all
CONFIG_CMD_DFL Default configuration; at the moment
this is includes all commands, except
the ones marked with "*" in the list
above.
If you don't define CONFIG_COMMANDS it defaults to
CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
override the default settings in the respective
include file.
Monitor commands can be included or excluded
from the build by using the #include files
"config_cmd_all.h" and #undef'ing unwanted
commands, or using "config_cmd_default.h"
and augmenting with additional #define's
for wanted commands.
The default command configuration includes all commands
except those marked below with a "*".
CONFIG_CMD_ASKENV * ask for env variable
CONFIG_CMD_AUTOSCRIPT Autoscript Support
CONFIG_CMD_BDI bdinfo
CONFIG_CMD_BEDBUG * Include BedBug Debugger
CONFIG_CMD_BMP * BMP support
CONFIG_CMD_BSP * Board specific commands
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_DOC * Disk-On-Chip Support
CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
CONFIG_CMD_ENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT partition support
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all found images
CONFIG_CMD_IMMAP * IMMR dump support
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw, mtest
CONFIG_CMD_MISC Misc functions like sleep etc
CONFIG_CMD_MMC * MMC memory mapped support
CONFIG_CMD_MII * MII utility commands
CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
CONFIG_CMD_PCI * pciinfo
CONFIG_CMD_PCMCIA * PCMCIA support
CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
host
CONFIG_CMD_PORTIO * Port I/O
CONFIG_CMD_REGINFO * Register dump
CONFIG_CMD_RUN run command in env variable
CONFIG_CMD_SAVES * save S record dump
CONFIG_CMD_SCSI * SCSI Support
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_USB * USB support
CONFIG_CMD_VFD * VFD support (TRAB)
CONFIG_CMD_BSP * Board SPecific functions
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_FSL * Microblaze FSL support
EXAMPLE: If you want all functions except of network
support you can write:
#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
#include "config_cmd_all.h"
#undef CONFIG_CMD_NET
Other Commands:
fdt (flattened device tree) command: CONFIG_OF_LIBFDT
Note: Don't enable the "icache" and "dcache" commands
(configuration option CFG_CMD_CACHE) unless you know
(configuration option CONFIG_CMD_CACHE) unless you know
what you (and your U-Boot users) are doing. Data
cache cannot be enabled on systems like the 8xx or
8260 (where accesses to the IMMR region must be
......@@ -769,7 +762,7 @@ The following options need to be configured:
- Real-Time Clock:
When CFG_CMD_DATE is selected, the type of the RTC
When CONFIG_CMD_DATE is selected, the type of the RTC
has to be selected, too. Define exactly one of the
following options:
......@@ -790,14 +783,14 @@ The following options need to be configured:
When CONFIG_TIMESTAMP is selected, the timestamp
(date and time) of an image is printed by image
commands like bootm or iminfo. This option is
automatically enabled when you select CFG_CMD_DATE .
automatically enabled when you select CONFIG_CMD_DATE .
- Partition Support:
CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
and/or CONFIG_ISO_PARTITION
If IDE or SCSI support is enabled (CFG_CMD_IDE or
CFG_CMD_SCSI) you must configure support for at least
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
CONFIG_CMD_SCSI) you must configure support for at least
one partition type as well.
- IDE Reset method:
......@@ -907,8 +900,8 @@ The following options need to be configured:
enable this define CONFIG_MMC. The MMC can be
accessed from the boot prompt by mapping the device
to physical memory similar to flash. Command line is
enabled with CFG_CMD_MMC. The MMC driver also works with
the FAT fs. This is enabled with CFG_CMD_FAT.
enabled with CONFIG_CMD_MMC. The MMC driver also works with
the FAT fs. This is enabled with CONFIG_CMD_FAT.
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
......@@ -1220,7 +1213,7 @@ The following options need to be configured:
include the appropriate I2C driver for the selected cpu.
This will allow you to use i2c commands at the u-boot
command line (as long as you set CFG_CMD_I2C in
command line (as long as you set CONFIG_CMD_I2C in
CONFIG_COMMANDS) and communicate with i2c based realtime
clock chips. See common/cmd_i2c.c for a description of the
command line interface.
......@@ -2328,7 +2321,7 @@ Low Level (hardware related) configuration options:
- CONFIG_LOOPW
Add the "loopw" memory command. This only takes effect if
the memory commands are activated globally (CFG_CMD_MEM).
the memory commands are activated globally (CONFIG_CMD_MEM).
- CONFIG_MX_CYCLIC
Add the "mdc" and "mwc" memory commands. These are cyclic
......@@ -2342,7 +2335,7 @@ Low Level (hardware related) configuration options:
This command will write 12345678 to address 100 all 10 ms.
This only takes effect if the memory commands are activated
globally (CFG_CMD_MEM).
globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT
- CONFIG_SKIP_RELOCATE_UBOOT
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment