Commit 6d365ea0 authored by Lucas Stach's avatar Lucas Stach Committed by Tom Rini

tegra20: add USB ULPI init code

This adds the required code to set up a ULPI USB port. It is
mostly a port of the Linux ULPI setup code with some tweaks
added for more correctness, discovered along the way of
debugging this.

To use this both CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT
have to be set in the board configuration file.
Signed-off-by: default avatarLucas Stach <dev@lynxeye.de>
Acked-by: default avatarIgor Grinberg <grinberg@compulab.co.il>
parent 141288b3
......@@ -1268,6 +1268,9 @@ The following options need to be configured:
viewport is supported.
To enable the ULPI layer support, define CONFIG_USB_ULPI and
CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
If your ULPI phy needs a different reference clock than the
standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
the appropriate value in Hz.
- MMC Support:
The MMC controller on the Intel PXA is supported. To
......
......@@ -32,9 +32,17 @@
#include <asm/arch/sys_proto.h>
#include <asm/arch/uart.h>
#include <asm/arch/usb.h>
#include <usb/ulpi.h>
#include <libfdt.h>
#include <fdtdec.h>
#ifdef CONFIG_USB_ULPI
#ifndef CONFIG_USB_ULPI_VIEWPORT
#error "To use CONFIG_USB_ULPI on Tegra Boards you have to also \
define CONFIG_USB_ULPI_VIEWPORT"
#endif
#endif
enum {
USB_PORTS_MAX = 4, /* Maximum ports we allow */
};
......@@ -68,11 +76,13 @@ enum dr_mode {
struct fdt_usb {
struct usb_ctlr *reg; /* address of registers in physical memory */
unsigned utmi:1; /* 1 if port has external tranceiver, else 0 */
unsigned ulpi:1; /* 1 if port has external ULPI transceiver */
unsigned enabled:1; /* 1 to enable, 0 to disable */
unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */
enum dr_mode dr_mode; /* dual role mode */
enum periph_id periph_id;/* peripheral id */
struct fdt_gpio_state vbus_gpio; /* GPIO for vbus enable */
struct fdt_gpio_state phy_reset_gpio; /* GPIO to reset ULPI phy */
};
static struct fdt_usb port[USB_PORTS_MAX]; /* List of valid USB ports */
......@@ -187,8 +197,8 @@ void usbf_reset_controller(struct fdt_usb *config, struct usb_ctlr *usbctlr)
*/
}
/* set up the USB controller with the parameters provided */
static int init_usb_controller(struct fdt_usb *config,
/* set up the UTMI USB controller with the parameters provided */
static int init_utmi_usb_controller(struct fdt_usb *config,
struct usb_ctlr *usbctlr, const u32 timing[])
{
u32 val;
......@@ -297,17 +307,115 @@ static int init_usb_controller(struct fdt_usb *config,
if (!loop_count)
return -1;
return 0;
}
/* Disable ICUSB FS/LS transceiver */
clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);
/* Select UTMI parallel interface */
clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
PTS_UTMI << PTS_SHIFT);
clrbits_le32(&usbctlr->port_sc1, STS);
static void power_up_port(struct usb_ctlr *usbctlr)
{
/* Deassert power down state */
clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN |
UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN);
clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN |
UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN);
return 0;
}
#ifdef CONFIG_USB_ULPI
/* if board file does not set a ULPI reference frequency we default to 24MHz */
#ifndef CONFIG_ULPI_REF_CLK
#define CONFIG_ULPI_REF_CLK 24000000
#endif
/* set up the ULPI USB controller with the parameters provided */
static int init_ulpi_usb_controller(struct fdt_usb *config,
struct usb_ctlr *usbctlr)
{
u32 val;
int loop_count;
struct ulpi_viewport ulpi_vp;
/* set up ULPI reference clock on pllp_out4 */
clock_enable(PERIPH_ID_DEV2_OUT);
clock_set_pllout(CLOCK_ID_PERIPH, PLL_OUT4, CONFIG_ULPI_REF_CLK);
/* reset ULPI phy */
if (fdt_gpio_isvalid(&config->phy_reset_gpio)) {
fdtdec_setup_gpio(&config->phy_reset_gpio);
gpio_direction_output(config->phy_reset_gpio.gpio, 0);
mdelay(5);
gpio_set_value(config->phy_reset_gpio.gpio, 1);
}
/* Reset the usb controller */
clock_enable(config->periph_id);
usbf_reset_controller(config, usbctlr);
/* enable pinmux bypass */
setbits_le32(&usbctlr->ulpi_timing_ctrl_0,
ULPI_CLKOUT_PINMUX_BYP | ULPI_OUTPUT_PINMUX_BYP);
/* Select ULPI parallel interface */
clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, PTS_ULPI << PTS_SHIFT);
/* enable ULPI transceiver */
setbits_le32(&usbctlr->susp_ctrl, ULPI_PHY_ENB);
/* configure ULPI transceiver timings */
val = 0;
writel(val, &usbctlr->ulpi_timing_ctrl_1);
val |= ULPI_DATA_TRIMMER_SEL(4);
val |= ULPI_STPDIRNXT_TRIMMER_SEL(4);
val |= ULPI_DIR_TRIMMER_SEL(4);
writel(val, &usbctlr->ulpi_timing_ctrl_1);
udelay(10);
val |= ULPI_DATA_TRIMMER_LOAD;
val |= ULPI_STPDIRNXT_TRIMMER_LOAD;
val |= ULPI_DIR_TRIMMER_LOAD;
writel(val, &usbctlr->ulpi_timing_ctrl_1);
/* set up phy for host operation with external vbus supply */
ulpi_vp.port_num = 0;
ulpi_vp.viewport_addr = (u32)&usbctlr->ulpi_viewport;
if (ulpi_init(&ulpi_vp)) {
printf("Tegra ULPI viewport init failed\n");
return -1;
}
ulpi_set_vbus(&ulpi_vp, 1, 1);
ulpi_set_vbus_indicator(&ulpi_vp, 1, 1, 0);
/* enable wakeup events */
setbits_le32(&usbctlr->port_sc1, WKCN | WKDS | WKOC);
/* Enable and wait for the phy clock to become valid in 100 ms */
setbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);
for (loop_count = 100000; loop_count != 0; loop_count--) {
if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
break;
udelay(1);
}
if (!loop_count)
return -1;
clrbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);
return 0;
}
#else
static int init_ulpi_usb_controller(struct fdt_usb *config,
struct usb_ctlr *usbctlr)
{
printf("No code to set up ULPI controller, please enable"
"CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT");
return -1;
}
#endif
static void config_clock(const u32 timing[])
{
......@@ -327,24 +435,21 @@ static int add_port(struct fdt_usb *config, const u32 timing[])
struct usb_ctlr *usbctlr = config->reg;
if (port_count == USB_PORTS_MAX) {
debug("tegrausb: Cannot register more than %d ports\n",
printf("tegrausb: Cannot register more than %d ports\n",
USB_PORTS_MAX);
return -1;
}
if (init_usb_controller(config, usbctlr, timing)) {
debug("tegrausb: Cannot init port\n");
if (config->utmi && init_utmi_usb_controller(config, usbctlr, timing)) {
printf("tegrausb: Cannot init port\n");
return -1;
}
if (config->utmi) {
/* Disable ICUSB FS/LS transceiver */
clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);
/* Select UTMI parallel interface */
clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
PTS_UTMI << PTS_SHIFT);
clrbits_le32(&usbctlr->port_sc1, STS);
power_up_port(usbctlr);
if (config->ulpi && init_ulpi_usb_controller(config, usbctlr)) {
printf("tegrausb: Cannot init port\n");
return -1;
}
port[port_count++] = *config;
return 0;
......@@ -406,6 +511,7 @@ int fdt_decode_usb(const void *blob, int node, unsigned osc_frequency_mhz,
phy = fdt_getprop(blob, node, "phy_type", NULL);
config->utmi = phy && 0 == strcmp("utmi", phy);
config->ulpi = phy && 0 == strcmp("ulpi", phy);
config->enabled = fdtdec_get_is_enabled(blob, node);
config->has_legacy_mode = fdtdec_get_bool(blob, node,
"nvidia,has-legacy-mode");
......@@ -415,10 +521,13 @@ int fdt_decode_usb(const void *blob, int node, unsigned osc_frequency_mhz,
return -FDT_ERR_NOTFOUND;
}
fdtdec_decode_gpio(blob, node, "nvidia,vbus-gpio", &config->vbus_gpio);
debug("enabled=%d, legacy_mode=%d, utmi=%d, periph_id=%d, vbus=%d, "
"dr_mode=%d\n", config->enabled, config->has_legacy_mode,
config->utmi, config->periph_id, config->vbus_gpio.gpio,
config->dr_mode);
fdtdec_decode_gpio(blob, node, "nvidia,phy-reset-gpio",
&config->phy_reset_gpio);
debug("enabled=%d, legacy_mode=%d, utmi=%d, ulpi=%d, periph_id=%d, "
"vbus=%d, phy_reset=%d, dr_mode=%d\n",
config->enabled, config->has_legacy_mode, config->utmi,
config->ulpi, config->periph_id, config->vbus_gpio.gpio,
config->phy_reset_gpio.gpio, config->dr_mode);
return 0;
}
......
......@@ -100,10 +100,12 @@ struct usb_ctlr {
/* 0x410 */
uint usb1_legacy_ctrl;
uint reserved12[3];
uint reserved12[4];
/* 0x420 */
uint reserved13[56];
/* 0x424 */
uint ulpi_timing_ctrl_0;
uint ulpi_timing_ctrl_1;
uint reserved13[53];
/* 0x500 */
uint reserved14[64 * 3];
......@@ -144,10 +146,24 @@ struct usb_ctlr {
#define VBUS_SENSE_CTL_AB_SESS_VLD 2
#define VBUS_SENSE_CTL_A_SESS_VLD 3
/* USB2_IF_ULPI_TIMING_CTRL_0 */
#define ULPI_OUTPUT_PINMUX_BYP (1 << 10)
#define ULPI_CLKOUT_PINMUX_BYP (1 << 11)
/* USB2_IF_ULPI_TIMING_CTRL_1 */
#define ULPI_DATA_TRIMMER_LOAD (1 << 0)
#define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1)
#define ULPI_STPDIRNXT_TRIMMER_LOAD (1 << 16)
#define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17)
#define ULPI_DIR_TRIMMER_LOAD (1 << 24)
#define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25)
/* USBx_IF_USB_SUSP_CTRL_0 */
#define ULPI_PHY_ENB (1 << 13)
#define UTMIP_PHY_ENB (1 << 12)
#define UTMIP_RESET (1 << 11)
#define USB_PHY_CLK_VALID (1 << 7)
#define USB_SUSP_CLR (1 << 5)
/* USBx_UTMIP_MISC_CFG1 */
#define UTMIP_PLLU_STABLE_COUNT_SHIFT 6
......@@ -203,12 +219,15 @@ struct usb_ctlr {
/* SB2_CONTROLLER_2_USB2D_PORTSC1_0 */
#define PTS_SHIFT 30
#define PTS_MASK (3U << PTS_SHIFT)
#define PTS_UTMI 0
#define PTS_UTMI 0
#define PTS_RESERVED 1
#define PTS_ULP 2
#define PTS_ULPI 2
#define PTS_ICUSB_SER 3
#define STS (1 << 29)
#define WKOC (1 << 22)
#define WKDS (1 << 21)
#define WKCN (1 << 20)
/* USBx_UTMIP_XCVR_CFG0_0 */
#define UTMIP_FORCE_PD_POWERDOWN (1 << 14)
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment