Commit 89ff5dbc authored by Paul Gortmaker's avatar Paul Gortmaker Committed by Tom Rix

sbc8548: use I/O accessors

Sweep throught the board specific file and replace the various
register proddings with the equivalent I/O accessors.
Signed-off-by: default avatarPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: default avatarKumar Gala <galak@kernel.crashing.org>
parent 8b23b608
......@@ -56,15 +56,15 @@ int checkboard (void)
volatile u_char *rev= (void *)CONFIG_SYS_BD_REV;
printf ("Board: Wind River SBC8548 Rev. 0x%01x\n",
(*rev) >> 4);
in_8(rev) >> 4);
/*
* Initialize local bus.
*/
local_bus_init ();
ecm->eedr = 0xffffffff; /* clear ecm errors */
ecm->eeer = 0xffffffff; /* enable ecm errors */
out_be32(&ecm->eedr, 0xffffffff); /* clear ecm errors */
out_be32(&ecm->eeer, 0xffffffff); /* enable ecm errors */
return 0;
}
......@@ -86,7 +86,7 @@ initdram(int board_type)
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
gur->ddrdllcr = 0x81000000;
out_be32(&gur->ddrdllcr, 0x81000000);
asm("sync;isync;msync");
udelay(200);
}
......@@ -123,24 +123,24 @@ local_bus_init(void)
sys_info_t sysinfo;
get_sys_info(&sysinfo);
clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
clkdiv = (in_be32(&lbc->lcrr) & LCRR_CLKDIV) * 2;
lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
gur->lbiuiplldcr1 = 0x00078080;
out_be32(&gur->lbiuiplldcr1, 0x00078080);
if (clkdiv == 16) {
gur->lbiuiplldcr0 = 0x7c0f1bf0;
out_be32(&gur->lbiuiplldcr0, 0x7c0f1bf0);
} else if (clkdiv == 8) {
gur->lbiuiplldcr0 = 0x6c0f1bf0;
out_be32(&gur->lbiuiplldcr0, 0x6c0f1bf0);
} else if (clkdiv == 4) {
gur->lbiuiplldcr0 = 0x5c0f1bf0;
out_be32(&gur->lbiuiplldcr0, 0x5c0f1bf0);
}
lbc->lcrr |= 0x00030000;
setbits_be32(&lbc->lcrr, 0x00030000);
asm("sync;isync;msync");
lbc->ltesr = 0xffffffff; /* Clear LBC error interrupts */
lbc->lteir = 0xffffffff; /* Enable LBC error interrupts */
out_be32(&lbc->ltesr, 0xffffffff); /* Clear LBC error IRQs */
out_be32(&lbc->lteir, 0xffffffff); /* Enable LBC error IRQs */
}
/*
......@@ -163,18 +163,18 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
lbc->or3 = CONFIG_SYS_OR3_PRELIM;
out_be32(&lbc->or3, CONFIG_SYS_OR3_PRELIM);
asm("msync");
lbc->br3 = CONFIG_SYS_BR3_PRELIM;
out_be32(&lbc->br3, CONFIG_SYS_BR3_PRELIM);
asm("msync");
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
asm("msync");
lbc->lsrt = CONFIG_SYS_LBC_LSRT;
lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
out_be32(&lbc->lsrt, CONFIG_SYS_LBC_LSRT);
out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
asm("msync");
/*
......@@ -186,7 +186,7 @@ sdram_init(void)
/*
* Issue PRECHARGE ALL command.
*/
lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_PCHALL);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
......@@ -196,7 +196,7 @@ sdram_init(void)
* Issue 8 AUTO REFRESH commands.
*/
for (idx = 0; idx < 8; idx++) {
lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_ARFRSH);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
......@@ -206,7 +206,7 @@ sdram_init(void)
/*
* Issue 8 MODE-set command.
*/
lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_MRW);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
......@@ -215,7 +215,7 @@ sdram_init(void)
/*
* Issue NORMAL OP command.
*/
lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_NORMAL);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
......@@ -263,45 +263,44 @@ testdram(void)
}
#endif
#if !defined(CONFIG_SPD_EEPROM)
#if !defined(CONFIG_SPD_EEPROM)
#define CONFIG_SYS_DDR_CONTROL 0xc300c000
/*************************************************************************
* fixed_sdram init -- doesn't use serial presence detect.
* assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
************************************************************************/
long int fixed_sdram (void)
{
#define CONFIG_SYS_DDR_CONTROL 0xc300c000
volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
ddr->cs0_bnds = 0x0000007f;
ddr->cs1_bnds = 0x008000ff;
ddr->cs2_bnds = 0x00000000;
ddr->cs3_bnds = 0x00000000;
ddr->cs0_config = 0x80010101;
ddr->cs1_config = 0x80010101;
ddr->cs2_config = 0x00000000;
ddr->cs3_config = 0x00000000;
ddr->timing_cfg_3 = 0x00000000;
ddr->timing_cfg_0 = 0x00220802;
ddr->timing_cfg_1 = 0x38377322;
ddr->timing_cfg_2 = 0x0fa044C7;
ddr->sdram_cfg = 0x4300C000;
ddr->sdram_cfg_2 = 0x24401000;
ddr->sdram_mode = 0x23C00542;
ddr->sdram_mode_2 = 0x00000000;
ddr->sdram_interval = 0x05080100;
ddr->sdram_md_cntl = 0x00000000;
ddr->sdram_data_init = 0x00000000;
ddr->sdram_clk_cntl = 0x03800000;
out_be32(&ddr->cs0_bnds, 0x0000007f);
out_be32(&ddr->cs1_bnds, 0x008000ff);
out_be32(&ddr->cs2_bnds, 0x00000000);
out_be32(&ddr->cs3_bnds, 0x00000000);
out_be32(&ddr->cs0_config, 0x80010101);
out_be32(&ddr->cs1_config, 0x80010101);
out_be32(&ddr->cs2_config, 0x00000000);
out_be32(&ddr->cs3_config, 0x00000000);
out_be32(&ddr->timing_cfg_3, 0x00000000);
out_be32(&ddr->timing_cfg_0, 0x00220802);
out_be32(&ddr->timing_cfg_1, 0x38377322);
out_be32(&ddr->timing_cfg_2, 0x0fa044C7);
out_be32(&ddr->sdram_cfg, 0x4300C000);
out_be32(&ddr->sdram_cfg_2, 0x24401000);
out_be32(&ddr->sdram_mode, 0x23C00542);
out_be32(&ddr->sdram_mode_2, 0x00000000);
out_be32(&ddr->sdram_interval, 0x05080100);
out_be32(&ddr->sdram_md_cntl, 0x00000000);
out_be32(&ddr->sdram_data_init, 0x00000000);
out_be32(&ddr->sdram_clk_cntl, 0x03800000);
asm("sync;isync;msync");
udelay(500);
#if defined (CONFIG_DDR_ECC)
/* Enable ECC checking */
ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
#else
ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
#endif
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment