Commit 94ba26f2 authored by Tom Rini's avatar Tom Rini

Revert "arm: Remove unregister MACH_TYPE_xxx uses"

This reverts commit 70b26cd0.

This is not a strict revert as it is easier to fix
board/atmark-techno/armadillo-800eva/armadillo-800eva.c to now the
correct name (same value) than to revert that change too.
Signed-off-by: 's avatarTom Rini <trini@konsulko.com>
parent 539cb803
......@@ -92,6 +92,11 @@ int board_early_init_f(void)
int board_init(void)
{
/*
* arch number of board
*/
gd->bd->bi_arch_number = MACH_TYPE_GOFLEXHOME;
/* address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
......
......@@ -271,6 +271,8 @@ int board_early_init_f(void)
DECLARE_GLOBAL_DATA_PTR;
int board_init(void)
{
/* board id for linux */
gd->bd->bi_arch_number = MACH_TYPE_ARMADILLO800EVA;
/* adress of boot parameters */
gd->bd->bi_boot_params = ARMADILLO_800EVA_SDRAM_BASE + 0x100;
......
......@@ -256,6 +256,9 @@ int board_early_init_f(void)
int board_init(void)
{
/* arch number of AT91SAM9X5EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
......
......@@ -175,6 +175,9 @@ int board_init(void)
irq_init();
#endif
/* arch number of the board */
gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_LCDK;
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
......
......@@ -277,6 +277,9 @@ int overwrite_console(void)
int board_init(void)
{
/* arch number of the board */
gd->bd->bi_arch_number = MACH_TYPE_EA20;
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
......
......@@ -252,6 +252,8 @@ int board_early_init_f(void)
int board_init(void)
{
gd->bd->bi_arch_number = MACH_TYPE_PICOSAM9G45;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
......
......@@ -138,6 +138,7 @@ int usb_gadget_handle_interrupts(int index)
int board_init(void)
{
gpmc_init();
gd->bd->bi_arch_number = MACH_TYPE_OMAP5_SEVM;
gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */
tca642x_set_inital_state(CONFIG_SYS_I2C_TCA642X_ADDR, tca642x_init);
......
......@@ -25,6 +25,8 @@
#define CONFIG_TEGRA_ENABLE_UARTA
#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE
#define CONFIG_MACH_TYPE MACH_TYPE_CARDHU
/* I2C */
#define CONFIG_SYS_I2C_TEGRA
......
......@@ -19,6 +19,8 @@
#define CONFIG_TEGRA_UARTA_SDIO1
#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE
#define CONFIG_MACH_TYPE MACH_TYPE_COLIBRI_TEGRA2
/* I2C */
#define CONFIG_SYS_I2C_TEGRA
......
......@@ -16,6 +16,11 @@
#define CONFIG_KW88F6281 /* SOC Name */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
* Machine type
*/
#define CONFIG_MACH_TYPE MACH_TYPE_ICONNECT
/*
* Compression configuration
*/
......
......@@ -24,6 +24,21 @@
(&((struct bcm2835_timer_regs *)BCM2835_TIMER_PHYSADDR)->clo)
#endif
/*
* 2835 is a SKU in a series for which the 2708 is the first or primary SoC,
* so 2708 has historically been used rather than a dedicated 2835 ID.
*
* We don't define a machine type for bcm2709/bcm2836 since the RPi Foundation
* chose to use someone else's previously registered machine ID (3139, MX51_GGC)
* rather than obtaining a valid ID:-/
*
* For the bcm2837, hopefully a machine type is not needed, since everything
* is DT.
*/
#ifdef CONFIG_BCM2835
#define CONFIG_MACH_TYPE MACH_TYPE_BCM2708
#endif
/* Memory layout */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE 0x00000000
......
......@@ -51,6 +51,7 @@
#define CONFIG_SYS_MAXARGS 32
/* setting board specific options */
#define CONFIG_MACH_TYPE MACH_TYPE_SMARTWEB
#define CONFIG_AUTO_COMPLETE
#define CONFIG_ENV_OVERWRITE 1 /* Overwrite ethaddr / serial# */
#define CONFIG_AUTO_COMPLETE
......
......@@ -24,6 +24,7 @@
#define CONFIG_ARM_ERRATA_430973
#define CONFIG_ARM_ERRATA_621766
#define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
......
......@@ -21,6 +21,8 @@
#define CONFIG_HW_WATCHDOG
#define CONFIG_MACH_TYPE MACH_TYPE_TS48XX
/* text base address used when linking */
#define CONFIG_SYS_TEXT_BASE 0x90008000
......
......@@ -18,6 +18,8 @@
#define CONFIG_TEGRA_ENABLE_UARTD
#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE
#define CONFIG_MACH_TYPE MACH_TYPE_VENTANA
/* SD/MMC */
#define CONFIG_GENERIC_MMC
......
......@@ -19,6 +19,8 @@
#define CONFIG_TEGRA_UARTA_UAA_UAB
#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE
#define CONFIG_MACH_TYPE MACH_TYPE_WHISTLER
/* I2C */
#define CONFIG_SYS_I2C_TEGRA
......
......@@ -19,6 +19,7 @@
#define CONFIG_SYS_TIMER_COUNTER \
(&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
#define CONFIG_MACH_TYPE MACH_TYPE_ZMX25
/*
* Environment settings
*/
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment