Commit a5ab44f6 authored by Fabien Parent's avatar Fabien Parent Committed by Tom Rini

davinci: omapl138_lcdk: configure ddr2

The SPL is unable to load u-boot because the DDR2 is not configured.
Configure the DDR2.
Signed-off-by: default avatarFabien Parent <fparent@baylibre.com>
Reviewed-by: default avatarTom Rini <trini@konsulko.com>
parent cd895dcb
......@@ -23,6 +23,7 @@ config TARGET_OMAPL138_LCDK
bool "OMAPL138 LCDK"
select SUPPORT_SPL
select SYS_DA850_PLL_INIT
select SYS_DA850_DDR_INIT
config TARGET_CALIMAIN
bool "Calimain board"
......
......@@ -78,6 +78,47 @@
#define CONFIG_SYS_DA850_PLL0_PLLM 24
#define CONFIG_SYS_DA850_PLL1_PLLM 21
/*
* DDR2 memory configuration
*/
#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
DV_DDR_PHY_EXT_STRBEN | \
(0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
(1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \
(1 << DV_DDR_SDCR_DDREN_SHIFT) | \
(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \
(4 << DV_DDR_SDCR_CL_SHIFT) | \
(3 << DV_DDR_SDCR_IBANK_SHIFT) | \
(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
(19 << DV_DDR_SDTMR1_RFC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RP_SHIFT) | \
(1 << DV_DDR_SDTMR1_RCD_SHIFT) | \
(2 << DV_DDR_SDTMR1_WR_SHIFT) | \
(6 << DV_DDR_SDTMR1_RAS_SHIFT) | \
(8 << DV_DDR_SDTMR1_RC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
(1 << DV_DDR_SDTMR1_WTR_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
(2 << DV_DDR_SDTMR2_XP_SHIFT) | \
(0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
(10 << DV_DDR_SDTMR2_XSNR_SHIFT) | \
(199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \
(1 << DV_DDR_SDTMR2_RTP_SHIFT) | \
(2 << DV_DDR_SDTMR2_CKE_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000492
#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
/*
* Serial Driver info
*/
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment