Commit a9aa3926 authored by Wolfgang Denk's avatar Wolfgang Denk

Drop support for CONFIG_SYS_ARM_WITHOUT_RELOC

When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support.  However, other recent changes led to a different
implementation (ELF relocation), where this no longer works.  By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.

So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: default avatarWolfgang Denk <wd@denx.de>
Tested-by: default avatarHeiko Schocher <hs@denx.de>
Tested-by: default avatarReinhard Meyer <u-boot@emk-elektronik.de>
parent 2e5167cc
......@@ -33,9 +33,6 @@ STANDALONE_LOAD_ADDR = 0xc100000
endif
endif
ifdef CONFIG_SYS_ARM_WITHOUT_RELOC
PLATFORM_CPPFLAGS += -DCONFIG_SYS_ARM_WITHOUT_RELOC
endif
PLATFORM_CPPFLAGS += -DCONFIG_ARM -D__ARM__
# Explicitly specifiy 32-bit ARM ISA since toolchain default can be -mthumb:
......@@ -68,9 +65,7 @@ endif
endif
LDSCRIPT := $(SRCTREE)/$(CPUDIR)/u-boot.lds
ifndef CONFIG_SYS_ARM_WITHOUT_RELOC
# needed for relocation
ifndef CONFIG_NAND_SPL
PLATFORM_LDFLAGS += -pie
endif
endif
......@@ -132,14 +132,11 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
.word 0x0badc0de
#endif
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/*
* the actual reset code
*/
......@@ -318,112 +315,6 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
/*
* the actual reset code
*/
reset:
/*
* set the cpu to SVC32 mode
*/
mrs r0,cpsr
bic r0,r0,#0x1f
orr r0,r0,#0xd3
msr cpsr,r0
#ifdef CONFIG_OMAP2420H4
/* Copy vectors to mask ROM indirect addr */
adr r0, _start /* r0 <- current position of code */
add r0, r0, #4 /* skip reset vector */
mov r2, #64 /* r2 <- size to copy */
add r2, r0, r2 /* r2 <- source end address */
mov r1, #SRAM_OFFSET0 /* build vect addr */
mov r3, #SRAM_OFFSET1
add r1, r1, r3
mov r3, #SRAM_OFFSET2
add r1, r1, r3
next:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
bne next /* loop until equal */
bl cpy_clk_code /* put dpll adjust code behind vectors */
#endif
/* the mask ROM code should have PLL and others stable */
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_crit
#endif
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
#ifndef CONFIG_PRELOADER
beq stack_setup
#endif /* CONFIG_PRELOADER */
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
/* Set up the stack */
stack_setup:
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
#ifdef CONFIG_PRELOADER
sub sp, r0, #128 /* leave 32 words for abort-stack */
#else
sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
#ifdef CONFIG_USE_IRQ
sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
#endif
sub sp, r0, #12 /* leave 3 words for abort-stack */
#endif /* CONFIG_PRELOADER */
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
clear_bss:
adr r2, _start
ldr r0, _bss_start_ofs /* find start of bss segment */
add r0, r0, r2
ldr r1, _bss_end_ofs /* stop here */
add r1, r1, r2
mov r2, #0x00000000 /* clear */
#ifndef CONFIG_PRELOADER
clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
bne clbss_l
#endif
ldr r0, _start_armboot_ofs
adr r1, _start
add r0, r0, r1
ldr pc, r0
_start_armboot_ofs:
#ifdef CONFIG_NAND_SPL
.word nand_boot - _start
#else
#ifdef CONFIG_ONENAND_IPL
.word start_oneboot - _start
#else
.word start_armboot - _start
#endif /* CONFIG_ONENAND_IPL */
#endif /* CONFIG_NAND_SPL */
#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
/*
*************************************************************************
*
......@@ -508,13 +399,7 @@ cpu_init_crit:
sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort stack
#else
adr r2, _start
sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
#endif
ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs)
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
......@@ -545,13 +430,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter in banked mode)
#else
adr r13, _start @ setup our mode stack (enter in banked mode)
sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ move to reserved a couple spots for abort stack
#endif
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
......@@ -567,13 +446,7 @@ cpu_init_crit:
.macro get_bad_stack_swi
sub r13, r13, #4 @ space on current stack for scratch reg.
str r0, [r13] @ save R0's value.
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r0, IRQ_STACK_START_IN @ get data regions start
#else
ldr r0, _armboot_start @ get data regions start
sub r0, r0, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
sub r0, r0, #(GENERATED_GBL_DATA_SIZE+8) @ move past gbl and a couple spots for abort stack
#endif
str lr, [r0] @ save caller lr in position 0 of saved stack
mrs r0, spsr @ get the spsr
str lr, [r0, #4] @ save spsr in position 1 of saved stack
......
......@@ -108,12 +108,6 @@ _TEXT_BASE:
_TEXT_PHY_BASE:
.word CONFIG_SYS_PHY_UBOOT_BASE
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
.globl _armboot_start
_armboot_start:
.word _start
#endif
/*
* These are defined in the board-specific linker script.
* Subtracting _start from them lets the linker put their
......@@ -157,7 +151,6 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
......@@ -419,188 +412,6 @@ _board_init_r_ofs:
.word board_init_r - _start
#endif
#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
/*
* the actual reset code
*/
reset:
/*
* set the cpu to SVC32 mode
*/
mrs r0, cpsr
bic r0, r0, #0x3f
orr r0, r0, #0xd3
msr cpsr, r0
/*
*************************************************************************
*
* CPU_init_critical registers
*
* setup important registers
* setup memory timing
*
*************************************************************************
*/
/*
* we do sys-critical inits only at reboot,
* not when booting from ram!
*/
cpu_init_crit:
/*
* When booting from NAND - it has definitely been a reset, so, no need
* to flush caches and disable the MMU
*/
#ifndef CONFIG_NAND_SPL
/*
* flush v4 I/D caches
*/
mov r0, #0
mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */
mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
/*
* disable MMU stuff and caches
*/
mrc p15, 0, r0, c1, c0, 0
bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS)
bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM)
orr r0, r0, #0x00000002 @ set bit 2 (A) Align
orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache
/* Prepare to disable the MMU */
adr r2, mmu_disable_phys
sub r2, r2, #(CONFIG_SYS_PHY_UBOOT_BASE - CONFIG_SYS_TEXT_BASE)
b mmu_disable
.align 5
/* Run in a single cache-line */
mmu_disable:
mcr p15, 0, r0, c1, c0, 0
nop
nop
mov pc, r2
mmu_disable_phys:
#ifdef CONFIG_DISABLE_TCM
/*
* Disable the TCMs
*/
mrc p15, 0, r0, c0, c0, 2 /* Return TCM details */
cmp r0, #0
beq skip_tcmdisable
mov r1, #0
mov r2, #1
tst r0, r2
mcrne p15, 0, r1, c9, c1, 1 /* Disable Instruction TCM if present*/
tst r0, r2, LSL #16
mcrne p15, 0, r1, c9, c1, 0 /* Disable Data TCM if present*/
skip_tcmdisable:
#endif
#endif
#ifdef CONFIG_PERIPORT_REMAP
/* Peri port setup */
ldr r0, =CONFIG_PERIPORT_BASE
orr r0, r0, #CONFIG_PERIPORT_SIZE
mcr p15,0,r0,c15,c2,4
#endif
/*
* Go setup Memory and board specific bits prior to relocation.
*/
bl lowlevel_init /* go setup pll,mux,memory */
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
beq stack_setup
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
#ifdef CONFIG_ENABLE_MMU
enable_mmu:
/* enable domain access */
ldr r5, =0x0000ffff
mcr p15, 0, r5, c3, c0, 0 /* load domain access register */
/* Set the TTB register */
ldr r0, _mmu_table_base
ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE
ldr r2, =0xfff00000
bic r0, r0, r2
orr r1, r0, r1
mcr p15, 0, r1, c2, c0, 0
/* Enable the MMU */
mrc p15, 0, r0, c1, c0, 0
orr r0, r0, #1 /* Set CR_M to enable MMU */
/* Prepare to enable the MMU */
adr r1, skip_hw_init
and r1, r1, #0x3fc
ldr r2, _TEXT_BASE
ldr r3, =0xfff00000
and r2, r2, r3
orr r2, r2, r1
b mmu_enable
.align 5
/* Run in a single cache-line */
mmu_enable:
mcr p15, 0, r0, c1, c0, 0
nop
nop
mov pc, r2
skip_hw_init:
#endif
/* Set up the stack */
stack_setup:
ldr r0, =CONFIG_SYS_UBOOT_BASE /* base of copy in DRAM */
sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
sub sp, r0, #12 /* leave 3 words for abort-stack */
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
clear_bss:
ldr r0, _bss_start /* find start of bss segment */
ldr r1, _bss_end /* stop here */
mov r2, #0 /* clear */
clbss_l:
str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
blo clbss_l
#ifndef CONFIG_NAND_SPL
ldr pc, _start_armboot
_start_armboot:
.word start_armboot
#else
b nand_boot
/* .word nand_boot*/
#endif
#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
#ifdef CONFIG_ENABLE_MMU
_mmu_table_base:
.word mmu_table
......@@ -687,14 +498,7 @@ phy_last_jump:
/* Save user registers (now in svc mode) r0-r12 */
stmia sp, {r0 - r12}
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r2, _armboot_start
sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
/* set base 2 words into abort stack */
sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8)
#else
ldr r2, IRQ_STACK_START_IN
#endif
/* get values for "aborted" pc and cpsr (into parm regs) */
ldmia r2, {r2 - r3}
/* grab pointer to old stack */
......@@ -709,16 +513,7 @@ phy_last_jump:
.endm
.macro get_bad_stack
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* setup our mode stack (enter in banked mode) */
ldr r13, _armboot_start
/* move past malloc pool */
sub r13, r13, #(CONFIG_SYS_MALLOC_LEN)
/* move to reserved a couple spots for abort stack */
sub r13, r13, #(GENERATED_GBL_DATA_SIZE + 8)
#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
#endif
/* save caller lr in position 0 of saved stack */
str lr, [r13]
......@@ -743,16 +538,7 @@ phy_last_jump:
sub r13, r13, #4
/* save R0's value. */
str r0, [r13]
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* get data regions start */
ldr r0, _armboot_start
/* move past malloc pool */
sub r0, r0, #(CONFIG_SYS_MALLOC_LEN)
/* move past gbl and a couple spots for abort stack */
sub r0, r0, #(GENERATED_GBL_DATA_SIZE + 8)
#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
#endif
/* save caller lr in position 0 of saved stack */
str lr, [r0]
/* get the spsr */
......
......@@ -79,12 +79,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
.globl _armboot_start
_armboot_start:
.word _start
#endif
/*
* These are defined in the board-specific linker script.
*/
......@@ -108,7 +102,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
......@@ -264,92 +257,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
/*
* the actual reset code
*/
reset:
/*
* set the cpu to SVC32 mode
*/
mrs r0,cpsr
bic r0,r0,#0x1f
orr r0,r0,#0x13
msr cpsr,r0
/*
* we do sys-critical inits only at reboot,
* not when booting from ram!
*/
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_crit
#endif
#ifdef CONFIG_LPC2292
bl lowlevel_init
#endif
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
beq stack_setup
#if CONFIG_SYS_TEXT_BASE
#ifndef CONFIG_LPC2292 /* already done in lowlevel_init */
ldr r2, =0x0 /* Relocate the exception vectors */
cmp r1, r2 /* and associated data to address */
ldmneia r0!, {r3-r10} /* 0x0. Do nothing if CONFIG_SYS_TEXT_BASE is */
stmneia r2!, {r3-r10} /* 0x0. Copy the first 15 words. */
ldmneia r0, {r3-r9}
stmneia r2, {r3-r9}
adrne r0, _start /* restore r0 */
#endif /* !CONFIG_LPC2292 */
#endif
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
/* Set up the stack */
stack_setup:
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
#ifdef CONFIG_USE_IRQ
sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
#endif
sub sp, r0, #12 /* leave 3 words for abort-stack */
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
clear_bss:
ldr r0, _bss_start /* find start of bss segment */
ldr r1, _bss_end /* stop here */
mov r2, #0x00000000 /* clear */
clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
blo clbss_l
ldr pc, _start_armboot
_start_armboot: .word start_armboot
#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
/*
*************************************************************************
*
......@@ -606,13 +513,7 @@ lock_loop:
stmia sp, {r0 - r12} @ Calling r0-r12
add r8, sp, #S_PC
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r2, _armboot_start
sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
#else
ldr r2, IRQ_STACK_START_IN
#endif
ldmia r2, {r2 - r4} @ get pc, cpsr, old_r0
add r0, sp, #S_FRAME_SIZE @ restore sp_SVC
......@@ -643,13 +544,7 @@ lock_loop:
.endm
.macro get_bad_stack
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r13, _armboot_start @ setup our mode stack
sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
......
......@@ -75,12 +75,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
.globl _armboot_start
_armboot_start:
.word _start
#endif
/*
* These are defined in the board-specific linker script.
*/
......@@ -104,7 +98,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
......@@ -316,127 +309,6 @@ _nand_boot: .word nand_boot
_board_init_r: .word board_init_r
#endif
#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
/*
* the actual start code
*/
start_code:
/*
* set the cpu to SVC32 mode
*/
mrs r0, cpsr
bic r0, r0, #0x1f
orr r0, r0, #0xd3
msr cpsr, r0
bl coloured_LED_init
bl red_LED_on
#if defined(CONFIG_AT91RM9200DK) || defined(CONFIG_AT91RM9200EK)
/*
* relocate exception table
*/
ldr r0, =_start
ldr r1, =0x0
mov r2, #16
copyex:
subs r2, r2, #1
ldr r3, [r0], #4
str r3, [r1], #4
bne copyex
#endif
#ifdef CONFIG_S3C24X0
/* turn off the watchdog */
# if defined(CONFIG_S3C2400)
# define pWTCON 0x15300000
# define INTMSK 0x14400008 /* Interupt-Controller base addresses */
# define CLKDIVN 0x14800014 /* clock divisor register */
#else
# define pWTCON 0x53000000
# define INTMSK 0x4A000008 /* Interupt-Controller base addresses */
# define INTSUBMSK 0x4A00001C
# define CLKDIVN 0x4C000014 /* clock divisor register */
# endif
ldr r0, =pWTCON
mov r1, #0x0
str r1, [r0]
/*
* mask all IRQs by setting all bits in the INTMR - default
*/
mov r1, #0xffffffff
ldr r0, =INTMSK
str r1, [r0]
# if defined(CONFIG_S3C2410)
ldr r1, =0x3ff
ldr r0, =INTSUBMSK
str r1, [r0]
# endif
/* FCLK:HCLK:PCLK = 1:2:4 */
/* default FCLK is 120 MHz ! */
ldr r0, =CLKDIVN
mov r1, #3
str r1, [r0]
#endif /* CONFIG_S3C24X0 */
/*
* we do sys-critical inits only at reboot,
* not when booting from ram!
*/
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_crit
#endif
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
beq stack_setup
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
/* Set up the stack */
stack_setup:
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
#ifdef CONFIG_USE_IRQ