Commit c0efc314 authored by Masahiro Yamada's avatar Masahiro Yamada

ARM: uniphier: change CONFIG_SPL_PAD_TO to 128KB

The Boot ROM supports authentication feature to prevent malformed
software from being run on products.  The signature is added at the
tail of the second stage loader (= SPL in U-boot terminology).

The size of the second stage loader was 64KB, and it was consistent
across SoCs.  The situation changed when LD20 SoC appeared; it loads
80KB second stage loader, and it is the only exception.

Currently, CONFIG_SPL_PAD_TO is set to 64KB and U-Boot proper is
loaded from the 64KB offset of non-volatile devices.  This means the
signature of LD20 SoC (located at 80KB offset) corrupts the U-Boot
proper image.

Let's move the U-Boot proper image to 128KB offset.  It uses 48KB
for nothing but padding, and we could actually locate the U-Boot
proper at 80KB offset.  However, the power of 2 generally seems a
better choice for the offset address.
Signed-off-by: 's avatarMasahiro Yamada <yamada.masahiro@socionext.com>
parent 0b93e3de
......@@ -86,9 +86,8 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
default 0x50 if ARCH_SUNXI
default 0x75 if ARCH_DAVINCI
default 0x80 if ARCH_UNIPHIER
default 0x8a if ARCH_MX6
default 0x100 if ARCH_ROCKCHIP
default 0x100 if ARCH_ROCKCHIP || ARCH_UNIPHIER
default 0x140 if ARCH_MVEBU
default 0x200 if ARCH_SOCFPGA || ARCH_AT91
default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \
......
......@@ -230,19 +230,19 @@
"nor_base=0x42000000\0" \
"sramupdate=setexpr tmp_addr $nor_base + 0x50000 &&" \
"tftpboot $tmp_addr u-boot-spl.bin &&" \
"setexpr tmp_addr $nor_base + 0x60000 &&" \
"setexpr tmp_addr $nor_base + 0x70000 && " \
"tftpboot $tmp_addr u-boot.bin\0" \
"emmcupdate=mmcsetn &&" \
"mmc partconf $mmc_first_dev 0 1 1 &&" \
"tftpboot u-boot-spl.bin &&" \
"mmc write $loadaddr 0 80 &&" \
"mmc write $loadaddr 0 100 && " \
"tftpboot u-boot.bin &&" \
"mmc write $loadaddr 80 780\0" \
"mmc write $loadaddr 100 700\0" \
"nandupdate=nand erase 0 0x00100000 &&" \
"tftpboot u-boot-spl.bin &&" \
"nand write $loadaddr 0 0x00010000 &&" \
"nand write $loadaddr 0 0x00020000 && " \
"tftpboot u-boot.bin &&" \
"nand write $loadaddr 0x00010000 0x000f0000\0" \
"nand write $loadaddr 0x00020000 0x000e0000\0" \
LINUXBOOT_ENV_SETTINGS
#define CONFIG_SYS_BOOTMAPSZ 0x20000000
......@@ -282,14 +282,18 @@
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000
/* subtract sizeof(struct image_header) */
#define CONFIG_SYS_UBOOT_BASE (0x60000 - 0x40)
#define CONFIG_SYS_UBOOT_BASE (0x70000 - 0x40)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_MAX_FOOTPRINT 0x10000
#if defined(CONFIG_ARCH_UNIPHIER_LD20)
#define CONFIG_SPL_MAX_SIZE 0x14000
#else
#define CONFIG_SPL_MAX_SIZE 0x10000
#endif
#if defined(CONFIG_ARCH_UNIPHIER_LD11)
#define CONFIG_SPL_BSS_START_ADDR 0x30012000
#elif defined(CONFIG_ARCH_UNIPHIER_LD20)
......@@ -297,4 +301,6 @@
#endif
#define CONFIG_SPL_BSS_MAX_SIZE 0x2000
#define CONFIG_SPL_PAD_TO 0x20000
#endif /* __CONFIG_UNIPHIER_COMMON_H__ */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment