Commit d145878d authored by Fabio Estevam's avatar Fabio Estevam Committed by Stefano Babic

mx6sxsabresd: Add Ethernet support

mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.

Add support for one FEC port initially.
Signed-off-by: default avatarFabio Estevam <fabio.estevam@freescale.com>
parent 5c045cdd
......@@ -981,6 +981,7 @@ struct mxc_ccm_reg {
#define BM_ANADIG_PLL_ENET_RSVD1 0x7FE00000
#define BF_ANADIG_PLL_ENET_RSVD1(v) \
(((v) << 21) & BM_ANADIG_PLL_ENET_RSVD1)
#define BM_ANADIG_PLL_ENET_REF_25M_ENABLE 0x00200000
#define BM_ANADIG_PLL_ENET_ENABLE_SATA 0x00100000
#define BM_ANADIG_PLL_ENET_ENABLE_PCIE 0x00080000
#define BM_ANADIG_PLL_ENET_PFD_OFFSET_EN 0x00040000
......
......@@ -65,6 +65,16 @@
#define IOMUX_GPR1_FEC_MASK (IOMUX_GPR1_FEC_CLOCK_MUX1_SEL_MASK \
| IOMUX_GPR1_FEC_CLOCK_MUX2_SEL_MASK)
#define IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK (0x1 << 17)
#define IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK (0x1 << 13)
#define IOMUX_GPR1_FEC1_MASK (IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK \
| IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK)
#define IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK (0x1 << 18)
#define IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK (0x1 << 14)
#define IOMUX_GPR1_FEC2_MASK (IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK \
| IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK)
#define IOMUXC_GPR13_SATA_PHY_8_RXEQ_0P5DB (0<<24)
#define IOMUXC_GPR13_SATA_PHY_8_RXEQ_1P0DB (1<<24)
#define IOMUXC_GPR13_SATA_PHY_8_RXEQ_1P5DB (2<<24)
......
......@@ -7,6 +7,7 @@
*/
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx6-pins.h>
......@@ -20,6 +21,8 @@
#include <fsl_esdhc.h>
#include <mmc.h>
#include <i2c.h>
#include <miiphy.h>
#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
......@@ -38,6 +41,21 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
PAD_CTL_SPEED_HIGH | \
PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE)
int dram_init(void)
{
gd->ram_size = PHYS_SDRAM_SIZE;
......@@ -60,11 +78,83 @@ static iomux_v3_cfg_t const usdhc4_pads[] = {
MX6_PAD_SD4_DATA7__GPIO6_IO_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const fec1_pads[] = {
MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII1_RD2__ENET1_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII1_RD3__ENET1_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII1_RXC__ENET1_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII1_TD2__ENET1_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII1_TD3__ENET1_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII1_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
};
static iomux_v3_cfg_t const peri_3v3_pads[] = {
MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const phy_control_pads[] = {
/* 25MHz Ethernet PHY Clock */
MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
/* ENET PHY Power */
MX6_PAD_ENET2_COL__GPIO2_IO_6 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* AR8031 PHY Reset */
MX6_PAD_ENET2_CRS__GPIO2_IO_7 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
static int setup_fec(void)
{
struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
int ret;
int reg;
/* Use 125MHz anatop loopback REF_CLK1 for ENET1 */
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, 0);
imx_iomux_v3_setup_multiple_pads(phy_control_pads,
ARRAY_SIZE(phy_control_pads));
/* Enable the ENET power, active low */
gpio_direction_output(IMX_GPIO_NR(2, 6) , 0);
/* Reset AR8031 PHY */
gpio_direction_output(IMX_GPIO_NR(2, 7) , 0);
udelay(500);
gpio_set_value(IMX_GPIO_NR(2, 7), 1);
reg = readl(&anatop->pll_enet);
reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE;
writel(reg, &anatop->pll_enet);
ret = enable_fec_anatop_clock(ENET_125MHz);
if (ret)
return ret;
return 0;
}
int board_eth_init(bd_t *bis)
{
imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
setup_fec();
return cpu_eth_init(bis);
}
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/* I2C1 for PMIC */
struct i2c_pads_info i2c_pad_info1 = {
......@@ -131,11 +221,37 @@ static int pfuze_init(void)
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
/*
* Enable 1.8V(SEL_1P5_1P8_POS_REG) on
* Phy control debug reg 0
*/
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
/* rgmii tx clock delay enable */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
int board_early_init_f(void)
{
setup_iomux_uart();
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
/* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */
imx_iomux_v3_setup_multiple_pads(peri_3v3_pads,
ARRAY_SIZE(peri_3v3_pads));
/* Active high for ncp692 */
gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
return 0;
}
......
......@@ -181,6 +181,23 @@
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
/* Network */
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment