Commit d7e8b2b9 authored by Simon Glass's avatar Simon Glass Committed by Tom Rini

arm: Remove da830evm board

This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: default avatarSimon Glass <sjg@chromium.org>
parent 05e682d4
......@@ -8,9 +8,6 @@ config TARGET_IPAM390
bool "IPAM390 board"
select SUPPORT_SPL
config TARGET_DA830EVM
bool "DA830 EVM board"
config TARGET_DA850EVM
bool "DA850 EVM board"
select SUPPORT_SPL
......
if TARGET_DA830EVM
config SYS_BOARD
default "da8xxevm"
config SYS_VENDOR
default "davinci"
config SYS_CONFIG_NAME
default "da830evm"
endif
if TARGET_DA850EVM
config SYS_BOARD
......
/*
* Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
*
* Base on code from TI. Original Notices follow:
*
* (C) Copyright 2008, Texas Instruments, Inc. http://www.ti.com/
*
* Modified for DA8xx EVM.
*
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*
* Parts are shamelessly stolen from various TI sources, original copyright
* follows:
* -----------------------------------------------------------------
*
* Copyright (C) 2004 Texas Instruments.
*
* ----------------------------------------------------------------------------
* SPDX-License-Identifier: GPL-2.0+
* ----------------------------------------------------------------------------
*/
#include <common.h>
#include <i2c.h>
#include <net.h>
#include <netdev.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emac_defs.h>
#include <asm/arch/pinmux_defs.h>
#include <asm/io.h>
#include <nand.h>
#include <asm/ti-common/davinci_nand.h>
#include <asm/arch/davinci_misc.h>
#ifdef CONFIG_DAVINCI_MMC
#include <mmc.h>
#include <asm/arch/sdmmc_defs.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
static const struct pinmux_resource pinmuxes[] = {
#ifdef CONFIG_SPI_FLASH
PINMUX_ITEM(spi0_pins_base),
PINMUX_ITEM(spi0_pins_scs0),
PINMUX_ITEM(spi0_pins_ena),
#endif
PINMUX_ITEM(uart2_pins_txrx),
PINMUX_ITEM(i2c0_pins),
#ifdef CONFIG_USB_DA8XX
PINMUX_ITEM(usb_pins),
#endif
#ifdef CONFIG_USE_NAND
PINMUX_ITEM(emifa_pins),
PINMUX_ITEM(emifa_pins_cs0),
PINMUX_ITEM(emifa_pins_cs2),
PINMUX_ITEM(emifa_pins_cs3),
#endif
#if defined(CONFIG_DRIVER_TI_EMAC)
PINMUX_ITEM(emac_pins_rmii),
PINMUX_ITEM(emac_pins_mdio),
PINMUX_ITEM(emac_pins_rmii_clk_source),
#endif
#ifdef CONFIG_DAVINCI_MMC
PINMUX_ITEM(mmc0_pins_8bit)
#endif
};
static const struct lpsc_resource lpsc[] = {
{ DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
{ DAVINCI_LPSC_SPI0 }, /* Serial Flash */
{ DAVINCI_LPSC_EMAC }, /* image download */
{ DAVINCI_LPSC_UART2 }, /* console */
{ DAVINCI_LPSC_GPIO },
#ifdef CONFIG_DAVINCI_MMC
{ DAVINCI_LPSC_MMC_SD },
#endif
};
#ifdef CONFIG_DAVINCI_MMC
static struct davinci_mmc mmc_sd0 = {
.reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
.host_caps = MMC_MODE_8BIT,
.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
.version = MMC_CTLR_VERSION_2,
};
int board_mmc_init(bd_t *bis)
{
mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID);
printf("%x\n", mmc_sd0.input_clk);
/* Add slot-0 to mmc subsystem */
return davinci_mmc_init(bis, &mmc_sd0);
}
#endif
int board_init(void)
{
#ifndef CONFIG_USE_IRQ
irq_init();
#endif
#ifdef CONFIG_NAND_DAVINCI
/* EMIFA 100MHz clock select */
writel(readl(&davinci_syscfg_regs->cfgchip3) & ~2,
&davinci_syscfg_regs->cfgchip3);
/* NAND CS setup */
writel((DAVINCI_ABCR_WSETUP(0) |
DAVINCI_ABCR_WSTROBE(2) |
DAVINCI_ABCR_WHOLD(0) |
DAVINCI_ABCR_RSETUP(0) |
DAVINCI_ABCR_RSTROBE(2) |
DAVINCI_ABCR_RHOLD(0) |
DAVINCI_ABCR_TA(2) |
DAVINCI_ABCR_ASIZE_8BIT),
&davinci_emif_regs->ab2cr);
#endif
/* arch number of the board */
gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA830_EVM;
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
/*
* Power on required peripherals
* ARM does not have access by default to PSC0 and PSC1
* assuming here that the DSP bootloader has set the IOPU
* such that PSC access is available to ARM
*/
if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
return 1;
/* setup the SUSPSRC for ARM to control emulation suspend */
writel(readl(&davinci_syscfg_regs->suspsrc) &
~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
DAVINCI_SYSCFG_SUSPSRC_SPI0 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
DAVINCI_SYSCFG_SUSPSRC_UART2),
&davinci_syscfg_regs->suspsrc);
/* configure pinmux settings */
if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
return 1;
/* enable the console UART */
writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
DAVINCI_UART_PWREMU_MGMT_UTRST),
&davinci_uart2_ctrl_regs->pwremu_mgmt);
return(0);
}
#ifdef CONFIG_NAND_DAVINCI
int board_nand_init(struct nand_chip *nand)
{
davinci_nand_init(nand);
return 0;
}
#endif
#if defined(CONFIG_DRIVER_TI_EMAC)
#define PHY_SW_I2C_ADDR 0x5f /* Address of PHY on i2c bus */
/*
* Initializes on-board ethernet controllers.
*/
int board_eth_init(bd_t *bis)
{
u_int8_t mac_addr[6];
u_int8_t switch_start_cmd[2] = { 0x01, 0x23 };
struct eth_device *dev;
/* Read Ethernet MAC address from EEPROM */
if (dvevm_read_mac_address(mac_addr))
/* set address env if not already set */
davinci_sync_env_enetaddr(mac_addr);
/* read the address back from env */
if (!eth_getenv_enetaddr("ethaddr", mac_addr))
return -1;
/* enable the Ethernet switch in the 3 port PHY */
if (i2c_write(PHY_SW_I2C_ADDR, 0, 0,
switch_start_cmd, sizeof(switch_start_cmd))) {
printf("Ethernet switch start failed!\n");
return -1;
}
/* finally, initialise the driver */
if (!davinci_emac_initialize()) {
printf("Error: Ethernet init failed!\n");
return -1;
}
dev = eth_get_dev();
/* provide the resulting addr to the driver */
memcpy(dev->enetaddr, mac_addr, 6);
dev->write_hwaddr(dev);
return 0;
}
#endif /* CONFIG_DRIVER_TI_EMAC */
CONFIG_ARM=y
CONFIG_ARCH_DAVINCI=y
CONFIG_TARGET_DA830EVM=y
CONFIG_SYS_PROMPT="U-Boot > "
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_SPI_FLASH=y
/*
* Copyright (C) 2008 Texas Instruments, Inc <www.ti.com>
*
* Based on davinci_dvevm.h. Original Copyrights follow:
*
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* Board
*/
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_USE_SPIFLASH
/*
* SoC Configuration
*/
#define CONFIG_MACH_DAVINCI_DA830_EVM
#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */
#define CONFIG_SOC_DA830 /* TI DA830 SoC */
#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_SYS_TEXT_BASE 0xc1080000
/*
* Memory Info
*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Start */
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
(32 << 20))
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
/*
* Serial Driver info
*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
/*
* I2C Configuration
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_DAVINCI
#define CONFIG_SYS_DAVINCI_I2C_SPEED 25000 /* 100Kbps won't work, H/W bug */
#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
/*
* I2C EEPROM definitions for catalyst 24W256 EEPROM chip
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/*
* Network & Ethernet Configuration
*/
#ifdef CONFIG_DRIVER_TI_EMAC
#define CONFIG_MII
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#endif
/*
* Flash & Environment
*/
#ifdef CONFIG_USE_NAND
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_NAND_DAVINCI
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_OFFSET (512 << 10)
#define CONFIG_ENV_SIZE (10 << 10) /* 10KB */
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_CS 3
#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_MASK_CLE 0x10
#define CONFIG_SYS_NAND_MASK_ALE 0x8
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#endif
#ifdef CONFIG_USE_NOR
#define CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
#define CONFIG_SYS_FLASH_SECT_SZ (64 << 10) /* 64KB */
#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3)
#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
#define PHYS_FLASH_SIZE (32 << 20) /* Flash size 32MB */
#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
#define CONFIG_SYS_FLASH_SPL_ACCESS
#endif
#ifdef CONFIG_USE_SPIFLASH
#undef CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE (16 << 10)
#define CONFIG_ENV_OFFSET (256 << 10)
#define CONFIG_ENV_SECT_SIZE 4096
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SPI
#define CONFIG_SPI_FLASH_WINBOND
#define CONFIG_DAVINCI_SPI
#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE
#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID)
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#endif
/*
* USB configuration
*/
#define CONFIG_USB_DA8XX /* Platform hookup to MUSB controller */
#define CONFIG_USB_MUSB_HCD
/*
* U-Boot general configuration
*/
#undef CONFIG_MISC_INIT_R
#undef CONFIG_BOOTDELAY
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
#define CONFIG_VERSION_VARIABLE
#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/*
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTARGS "mem=32M console=ttyS2,115200n8 root=/dev/mtdblock/2 rw noinitrd ip=dhcp"
#define CONFIG_BOOTCOMMAND ""
#define CONFIG_BOOTDELAY 3
/*
* U-Boot commands
*/
#define CONFIG_CMD_ENV
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#ifndef CONFIG_DRIVER_TI_EMAC
#undef CONFIG_CMD_DHCP
#undef CONFIG_CMD_MII
#undef CONFIG_CMD_PING
#endif
#ifdef CONFIG_USE_NAND
#define CONFIG_CMD_NAND
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#endif
#ifdef CONFIG_USE_SPIFLASH
#define CONFIG_CMD_SPI
#define CONFIG_CMD_SF
#endif
/* SD/MMC configuration */
#ifndef CONFIG_USE_NAND
#define CONFIG_MMC
#define CONFIG_DAVINCI_MMC_SD1
#define CONFIG_GENERIC_MMC
#define CONFIG_DAVINCI_MMC
#endif
/*
* Enable MMC commands only when
* MMC support is present
*/
#if defined(CONFIG_MMC) || defined(CONFIG_USB_DA8XX)
#define CONFIG_DOS_PARTITION /* include support for FAT/storage */
#define CONFIG_CMD_FAT /* include support for FAT cmd */
#endif
#ifdef CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_CMD_EXT2
#endif
#if !defined(CONFIG_USE_NAND) && \
!defined(CONFIG_USE_NOR) && \
!defined(CONFIG_USE_SPIFLASH)
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SIZE (16 << 10)
#undef CONFIG_CMD_ENV
#endif
#ifdef CONFIG_USB_DA8XX
#ifdef CONFIG_USB_MUSB_HCD /* include support for usb host */
#define CONFIG_CMD_USB /* include support for usb cmd */
#define CONFIG_USB_STORAGE /* MSC class support */
#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */
#ifdef CONFIG_USB_KEYBOARD /* HID class support */
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_PREBOOT "usb start"
#endif /* CONFIG_USB_KEYBOARD */
#endif /* CONFIG_USB_MUSB_HCD */
#ifdef CONFIG_USB_MUSB_UDC
/* USB device configuration */
#define CONFIG_USB_DEVICE 1
#define CONFIG_USB_TTY 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
/* Change these to suit your needs */
#define CONFIG_USBD_VENDORID 0x0451
#define CONFIG_USBD_PRODUCTID 0x5678
#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
#define CONFIG_USBD_PRODUCT_NAME "DA830EVM"
#endif /* CONFIG_USB_MUSB_UDC */
#endif /* CONFIG_USB_DA8XX */
#ifdef CONFIG_MTD_PARTITIONS
#define MTDIDS_DEFAULT "nand0=davinci_nand.1"
#define PART_BOOT "512k(bootloader)ro,"
#define PART_PARAMS "512k(params)ro,"
#define PART_KERNEL "4m(kernel),"
#define PART_REST "-(filesystem)"
#define MTDPARTS_DEFAULT \
"mtdparts=davinci_nand.1:" PART_BOOT PART_PARAMS PART_KERNEL PART_REST
#endif
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
#endif /* __CONFIG_H */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment