Commit fa8a485d authored by Hans de Goede's avatar Hans de Goede

sunxi: Sync sun8i-h3-orangepi-plus.dts with upstream

This enables extra USB controllers which enable use of the 3rd USB
port on the new Orange Pi Plus 2E variant.
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Acked-by: default avatarIan Campbell <ijc@hellion.org.uk>
parent 74fcc927
......@@ -40,26 +40,13 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/* The Orange Pi Plus is an extended version of the Orange Pi 2 */
#include "sun8i-h3-orangepi-2.dts"
/ {
model = "Xunlong Orange Pi Plus";
model = "Xunlong Orange Pi Plus / Plus 2 / Plus 2E";
compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
......@@ -71,75 +58,42 @@
enable-active-high;
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&leds_opc>;
status_led {
label = "status:red:user";
gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
};
};
r_leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&leds_r_opc>;
tx {
label = "pwr:green:user";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
r_gpio_keys {
compatible = "gpio-keys";
input-name = "sw4";
pinctrl-names = "default";
pinctrl-0 = <&sw_r_opc>;
&ehci2 {
status = "okay";
};
sw4@0 {
label = "sw4";
linux,code = <BTN_0>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
};
&ehci3 {
status = "okay";
};
&pio {
leds_opc: led_pins@0 {
allwinner,pins = "PA15";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&r_pio {
leds_r_opc: led_pins@0 {
allwinner,pins = "PL10";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
&mmc2_8bit_pins {
/* Increase drive strength for DDR modes */
allwinner,drive = <SUN4I_PINCTRL_40_MA>;
/* eMMC is missing pull-ups */
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
sw_r_opc: key_pins@0 {
allwinner,pins = "PL03";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
&ohci1 {
status = "okay";
};
&ehci1 {
&ohci2 {
status = "okay";
};
&ehci3 {
&ohci3 {
status = "okay";
};
......@@ -152,33 +106,6 @@
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
status = "okay";
};
&reg_usb1_vbus {
gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usb1_vbus_pin_a {
allwinner,pins = "PG13";
};
&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb3_vbus-supply = <&reg_usb3_vbus>;
status = "okay";
};
......@@ -541,6 +541,16 @@
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc2_8bit_pins: mmc2_8bit {
allwinner,pins = "PC5", "PC6", "PC8",
"PC9", "PC10", "PC11",
"PC12", "PC13", "PC14",
"PC15", "PC16";
allwinner,function = "mmc2";
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
ahb_rst: reset@01c202c0 {
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment